Nissan Murano. Manual - part 323

DAS-182

< SYMPTOM DIAGNOSIS >

[BSW]

BSW WARNING LAMP DOES NOT TURNED ON

BSW WARNING LAMP DOES NOT TURNED ON

Description

INFOID:0000000009723387

The BSW warning lamp in the combination meter does not turn ON when turning on the ignition switch

Diagnosis Procedure

INFOID:0000000009723388

1.

CHECK COMBINATION METER

Turn the ignition switch from OFF to ON to check that “BSW W/L” included in “DATA MONITOR” in “METER/
M&A” operates normally.
Is the inspection result normal?

YES

>> Replace the combination meter. Refer to 

MWI-105, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK SELF-DIAGNOSIS RESULTS OF COMBINATION METER

1.

Perform “All DTC Reading” with CONSULT.

2.

Check if the DTC is detected in self-diagnosis results of “METER/M&A”. Refer to 

MWI-77, "DTC Index"

.

Is any DTC detected?

YES

>> Repair or replace malfunctioning parts.

NO

>> GO TO 3.

3.

CHECK SELF-DIAGNOSIS RESULTS OF CAMERA CONTROL UNIT

Check if the DTC is detected in self-diagnosis results of “AVM” Refer to 

DAS-128, "DTC Index"

.

Is any DTC detected?

YES

>> Repair or replace malfunctioning parts.

NO

>> Replace the camera control unit. Refer to 

DAS-187, "Removal and Installation"

.

DAS

BSW ON INDICATOR DOES NOT TURNED ON

DAS-183

< SYMPTOM DIAGNOSIS >

[BSW]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

BSW ON INDICATOR DOES NOT TURNED ON

Description

INFOID:0000000009723389

The BSW ON indicator lamp in the combination meter does not turn ON when turning on the ignition switch

Diagnosis Procedure

INFOID:0000000009723390

1.

CHECK COMBINATION METER

Turn the ignition switch from OFF to ON to check that “BSW IND” included in “DATA MONITOR” in “METER/
M&A” operates normally.
Is the inspection result normal?

YES

>> Replace the combination meter. Refer to 

MWI-105, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK SELF-DIAGNOSIS RESULTS OF COMBINATION METER

1.

Perform “All DTC Reading” with CONSULT.

2.

Check if the DTC is detected in self-diagnosis results of “METER/M&A” Refer to 

MWI-77, "DTC Index"

.

Is any DTC detected?

YES

>> Repair or replace malfunctioning parts.

NO

>> GO TO 3.

3.

CHECK SELF-DIAGNOSIS RESULTS OF CAMERA CONTROL UNIT

Check if the DTC is detected in self-diagnosis results of “AVM” Refer to 

DAS-128, "DTC Index"

.

Is any DTC detected?

YES

>> Repair or replace malfunctioning parts.

NO

>> Replace the camera control unit. Refer to 

DAS-187, "Removal and Installation"

.

DAS-184

< SYMPTOM DIAGNOSIS >

[BSW]

SYSTEM SETTINGS CANNOT BE TURNED ON/OFF ON THE NAVIGATION 

SCREEN

SYSTEM SETTINGS CANNOT BE TURNED ON/OFF ON THE NAVIGATION
SCREEN

Description

INFOID:0000000009723391

• BSW system setting is not selectable on the navigation screen.

NOTE:
When the ignition switch is in ACC position, Blind Spot Warning system settings cannot be changed.

- “Blind Spot Warning” is not indicated on the navigation screen.
- The switching between ON and OFF cannot be performed by operating the navigation system.
- The item “Blind Spot Warning” on the navigation screen is not active.
• The Blind Spot Warning or system setting differs from the one set at the previous driving. 

NOTE:
Turn OFF the ignition switch and wait for 5 seconds or more.

Diagnosis Procedure

INFOID:0000000009723392

1.

CHECK BSW SYSTEM SETTING

1.

Start the engine.

2.

Check that the Blind Spot Warning system settings is selectable on the navigation screen.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

PERFORM THE SELF-DIAGNOSIS

1.

Perform self-diagnosis with CONSULT. 

2.

Check if the DTC is detected in self-diagnosis results of “AVM” and “MULTI AV”. Refer to the following.

-

AVM: 

DAS-128, "DTC Index"

-

MULTI AV: 

AV-340, "DTC Index"

Is any DTC detected?

YES

>> Repair or replace malfunctioning parts.

NO

>> INSPECTION END

3.

CHECK MULTIFUNCTION SWITCH

Operate the multifunction switch to check that the audio, navigation system, and air conditioner operate prop-
erly.

Is the inspection result normal?

YES

>> Replace the camera control unit. Refer to 

DAS-187, "Removal and Installation"

.

NO

>> Repair or replace malfunctioning parts.

DAS

NORMAL OPERATING CONDITION

DAS-185

< SYMPTOM DIAGNOSIS >

[BSW]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

NORMAL OPERATING CONDITION

Description

INFOID:0000000009723393

PRECAUTIONS FOR BLIND SPOT WARNING (BSW)

• The BSW system is not a replacement for proper driving procedure and is not designed to prevent contact

with vehicles or objects. When changing lanes, always use the side and rear mirrors and turn and look in the
direction you will move to ensure it is safe to change lanes. Never rely solely on the BSW system.

• The rear view camera may not detect properly under the following conditions:
- When towing a trailer.
- When strong light enters the rear view camera. (For example, direct sunlight or headlight from the rear)
- When ambient brightness changes instantly. (For example, when the vehicle enters or exits a tunnel or

passes under a bridge.)

• Automatic washer and blower may not be able to secure detection capability when excessive dirt adheres on

the camera lens. 

• The camera unit may not be able to detect when certain objects are present such as:
- Pedestrians, bicycles, animals
- Several types of vehicles such as motorcycles
- Oncoming vehicles
- A vehicle approaching rapidly from behind.
- A vehicle which your vehicle overtakes rapidly.
• The rear view camera may not be able to detect property when your vehicle travels beside the middle sec-

tion of a vehicle with long wheelbase(e.g. trailer truck, semi-trailer, tractor).

• The rear view camera detection zone is designed based on a standard lane width. When driving in a wider

lane, the camera unit may not detect vehicles in an adjacent lane. When driving in a narrow lane, the camera
unit may detect vehicles driving two lanes away.

• The rear view camera is designed to ignore most stationary objects, however objects such as guardrails,

walls, foliage and parked vehicles may occasionally be detected. This is a normal operating condition.

• The rear view camera may detect reflection image of vehicles or roadside objects that are not actually in the

detection zone, especially when the road is wet.