Juke F15 (2012 year). Service Repair Manual - part 336

 

  Index      Manuals     Juke F15 (2012 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     334      335      336      337     ..

 

 

Juke F15 (2012 year). Service Repair Manual - part 336

 

 

SRC-48

< DTC/CIRCUIT DIAGNOSIS >

B1050, B1055 DRIVER AIR BAG MODULE

Is DTC detected?

YES

>> GO TO 5.

NO

>> INSPECTION END

5.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to 

SR-13, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-47, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

B1051, B1056 DRIVER AIR BAG MODULE

SRC-49

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1051, B1056 DRIVER AIR BAG MODULE

DTC Logic

INFOID:0000000006439888

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-49, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006439889

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK SPIRAL CABLE CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.

3.

Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1051
B1056

DRIVER AIRBAG 
MODULE 
[GND-SHORT]

Driver air bag module circuit is shorted to ground
(including the spiral cable)

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit

SRC-50

< DTC/CIRCUIT DIAGNOSIS >

B1051, B1056 DRIVER AIR BAG MODULE

4.

Check continuity between driver air bag module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-16, "Removal and Installation"

.

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-49, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 5.

NO

>> INSPECTION END

5.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to 

SR-13, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-49, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Driver air bag module

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Connector

Terminal

M301

10

M32

28

Existed

11

30

Driver side air bag module

Ground

Continuity 

Connector

Terminal

M301

10

Not existed

11

B1052, B1057 DRIVER AIR BAG MODULE

SRC-51

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1052, B1057 DRIVER AIR BAG MODULE

DTC Logic

INFOID:0000000006439890

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-51, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006439891

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK SPIRAL CABLE CIRCUIT-I

1.

Turn ignition switch OFF.

2.

Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.

3.

Check continuity between combination switch (spiral cable) terminals.

Is the inspection result normal?

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1052
B1057

DRIVER AIRBAG 
MODULE 
[SHORT]

Driver air bag module circuit are shorted to each 
other
(including the spiral cable)

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Terminal

M301

10

11

Not existed

SRC-52

< DTC/CIRCUIT DIAGNOSIS >

B1052, B1057 DRIVER AIR BAG MODULE

YES

>> GO TO 4.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-16, "Removal and Installation"

.

4.

CHECK SPIRAL CABLE CIRCUIT-II

Check continuity between combination switch (spiral cable) terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-16, "Removal and Installation"

.

5.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-51, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 6.

NO

>> INSPECTION END

6.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to 

SR-13, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-51, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Terminal

M32

28

30

Not existed

B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT

SRC-53

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000006439892

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-53, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006439893

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-53, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1058
B1059
B1060
B1061
B1062
B1063

CONTROL UNIT 

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

SRC-54

< DTC/CIRCUIT DIAGNOSIS >

B1065, B1070 PASSENGER AIR BAG MODULE

B1065, B1070 PASSENGER AIR BAG MODULE

DTC Logic

INFOID:0000000006439894

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-54, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006439895

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-54, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE PASSENGER AIR BAG MODULE

1.

Replace passenger air bag module. Refer to 

SR-19, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-54, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1065
B1070

ASSIST A/B MODULE 
[OPEN]

Passenger air bag module circuit is open

• Harness or connectors

(The module circuit is open.)

• Malfunction in passenger air bag module
• Malfunction in air bag diagnosis sensor unit

B1065, B1070 PASSENGER AIR BAG MODULE

SRC-55

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1.

NO

>> INSPECTION END

SRC-56

< DTC/CIRCUIT DIAGNOSIS >

B1066, B1071 PASSENGER AIR BAG MODULE

B1066, B1071 PASSENGER AIR BAG MODULE

DTC Logic

INFOID:0000000006439896

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-56, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006439897

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-56, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE PASSENGER AIR BAG MODULE

1.

Replace passenger air bag module. Refer to 

SR-19, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-56, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of CON-

SULT-III

DTC detecting condition

Possible cause

B1066
B1071

ASSIST A/B MODULE 
[VB-SHORT]

Passenger air bag module circuit is 
shorted to power supply circuit

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in passenger air bag module
• Malfunction in air bag diagnosis sensor unit

B1066, B1071 PASSENGER AIR BAG MODULE

SRC-57

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1.

NO

>> INSPECTION END

SRC-58

< DTC/CIRCUIT DIAGNOSIS >

B1067, B1072 PASSENGER AIR BAG MODULE

B1067, B1072 PASSENGER AIR BAG MODULE

DTC Logic

INFOID:0000000006439898

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-58, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006439899

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-58, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE PASSENGER AIR BAG MODULE

1.

Replace passenger air bag module. Refer to 

SR-19, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-58, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1067
B1072

ASSIST A/B MODULE 
[GND-SHORT]

Passenger air bag module circuit is 
shorted to ground

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in passenger air bag module
• Malfunction in air bag diagnosis sensor unit

B1067, B1072 PASSENGER AIR BAG MODULE

SRC-59

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1.

NO

>> INSPECTION END

SRC-60

< DTC/CIRCUIT DIAGNOSIS >

B1068, B1073 PASSENGER AIR BAG MODULE

B1068, B1073 PASSENGER AIR BAG MODULE

DTC Logic

INFOID:0000000006439900

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-60, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006439901

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-60, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE PASSENGER AIR BAG MODULE

1.

Replace passenger air bag module. Refer to 

SR-19, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-60, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1068
B1073

ASSIST A/B MODULE 
[SHORT]

Passenger air bag module circuits   are 
shorted to each other

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in passenger air bag module
• Malfunction in air bag diagnosis sensor unit

B1068, B1073 PASSENGER AIR BAG MODULE

SRC-61

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1.

NO

>> INSPECTION END

SRC-62

< DTC/CIRCUIT DIAGNOSIS >

B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT

B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000006439902

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-62, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006439903

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-62, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1074
B1075
B1076
B1077
B1078
B1079

CONTROL UNIT 

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

B1080, B1096 DRIVER AIR BAG MODULE

SRC-63

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1080, B1096 DRIVER AIR BAG MODULE

DTC Logic

INFOID:0000000006439904

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-63, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006439905

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK SPIRAL CABLE CIRCUIT-I

1.

Turn ignition switch OFF.

2.

Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.

3.

Check continuity between combination switch (spiral cable) terminals.

Is the inspection result normal?

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1080
B1096

DRIVER AIRBAG 
MODULE 
[SHORT]

Driver air bag module circuit are shorted to each 
other
(including the spiral cable)

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Connector

Terminal

M301

10

M319

11

Not existed

 

 

 

 

 

 

 

Content      ..     334      335      336      337     ..