Mitsubishi Outlander (2013+). Manual - part 639

 

  Index      Mitsubishi     Mitsubishi Outlander - service repair manual 2013 year

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  637  638  639  640   ..

 

 

Mitsubishi Outlander (2013+). Manual - part 639

 

 

COMBINATION METER

CHASSIS ELECTRICAL

54A-41

YES : 

Go to Step 6.

NO : 

Repair the connector(s) or wiring harness, 
and then go to Step 7.

STEP 6. M.U.T.-III actuator test

• Item 03: Fuel gauge (target value): 0 →100%

OK: The fuel gauge operates.

Q: Is the check result normal?

YES : 

Go to Step 7.

NO : 

Replace the combination meter.

STEP 7. Check whether the diagnosis code is 
reset.
Check again if the diagnosis code is set to the combi-
nation meter.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from "LOCK" (OFF) 

position to "ON" position.

(3) Check if diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the combination meter.

NO : 

The diagnosis is complete.

Code No.B1209 Test mode

TROUBLE JUDGMENT

When the mode is changed to the meter test mode 
(supplier mode) with the ignition switch at the ON 
position and the diagnosis code No. U1190 is not 
stored, the combination meter stores the diagnosis 
code No. B1209.

PROBABLE CAUSES

Malfunction of combination meter

Code No.B2463 Rheostat switch sticking

TROUBLE JUDGMENT

If the combination meter detects the meter informa-
tion switch <Standard meter> or rheostat illumination 
switch <High contrast meter> pressed state for 60 
seconds or more continuously with the ignition switch 
at the ON position and the diagnosis code No. U1190 
is not stored, the diagnosis code No. B2463 is 
stored.

PROBABLE CAUSES

• Malfunction of combination meter

• Malfunction of meter information switch <Stand-

ard meter> or rheostat illumination switch <High 
contrast meter>

DIAGNOSIS PROCEDURE

STEP 1. Switch check
Check whether the meter information switch <Stand-
ard meter> or the rheostat illumination switch <High 
contrast meter> on the combination meter is stuck 
too hard to turn on.

Q: Is the check result normal?

YES : 

Go to Step 2.

NO : 

Replace the combination meter, and then go 
to Step 2.

STEP 2. M.U.T.-III diagnosis code
Check again if the diagnosis code is set to the combi-
nation meter.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from "LOCK" (OFF) 

position to "ON" position.

(3) Check if diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the combination meter, and then 

go to Step 3.

NO : 

The diagnosis is complete.

STEP 3. Check whether the diagnosis code is 
reset.
Check again if the diagnosis code is set to the combi-
nation meter.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from "LOCK" (OFF) 

position to "ON" position.

(3) Check if diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Go to Step 1.

NO : 

The diagnosis is complete.

COMBINATION METER

CHASSIS ELECTRICAL

54A-42

Code No.B2464 Meter information SW sticking <High contrast meter>

CAUTION

Before replacing the combination meter, ensure 
that the power supply circuit, the earth circuit 
and the communication circuit are normal.

TROUBLE JUDGMENT

If the combination meter detects the meter informa-
tion switch pressed state for 60 seconds or more 
continuously with the ignition switch at the ON posi-
tion and the diagnosis code No. U1190 is not stored, 
the diagnosis code No. B2464 is stored.

PROBABLE CAUSES

• Damaged harness wires and connectors

• Malfunction of meter information switch

• Malfunction of combination meter

DIAGNOSIS PROCEDURE

STEP 1. Meter information switch check
Check the meter information switch. Refer to 

P.54A-83

.

Q: Is the check result normal?

YES : 

Go to Step 2.

NO : 

Replace the meter information switch.

STEP 2. Resistance measurement at the meter 
information switch connector
(1) Disconnect the meter information switch 

connector, the measure at the harness side.

(2) Measure the resistance between the meter 

information switch connector (earth terminal) and 

the body earth.

OK: Continuity exists (2 

Ω or less)

Q: Is the check result normal?

YES : 

Go to Step 4.

NO : 

Go to Step 3.

STEP 3. Check of open circuit in body earth line 
between meter information switch connector and 
body earth.

Q: Is the check result normal?

YES : 

Go to Step 4.

NO : 

Repair the connector(s) or wiring harness.

STEP 4. Check of open circuit in MODE line 
between combination meter connector and meter 
information switch connector. 

Q: Is the check result normal?

YES : 

Go to Step 5.

NO : 

Repair the connector(s) or wiring harness.

STEP 5. Check whether the diagnosis code is 
reset.
Check again if the diagnosis code is set to the combi-
nation meter.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from "LOCK" (OFF) 

position to "ON" position.

(3) Check if diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the combination meter.

NO : 

The diagnosis is complete.

Code No.U0100 Engine CAN timeout

CAUTION

• If the diagnosis code No. U0100 is set, be sure 

to diagnose the CAN bus line.

• Before replacing the ECU or combination 

meter, ensure that the power supply circuit, 
the earth circuit and the communication cir-
cuit are normal.

DIAGNOSTIC FUNCTION

The combination meter sets diagnosis code 
No.U0100 when it cannot receive signals from the 
engine-ECU.

JUDGEMENT CRITERIA

With the ignition switch is at ON position, the diagno-
sis code No. U1190 is not stored, if the communica-
tion with engine-ECU cannot be established for 5000 
ms or more, the combination meter determines that a 
problem has occurred.

PROBABLE CAUSES

• Malfunction of CAN bus line

• Malfunction of engine-ECU

• Malfunction of combination meter

COMBINATION METER

CHASSIS ELECTRICAL

54A-43

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.

Q: Is the check result normal?

YES : 

Go to Step 2.

NO : 

Repair the CAN bus line (Refer to GROUP 
54C 

− Troubleshooting ).

STEP 2. M.U.T.-III other system diagnosis code
Check if diagnosis code is set to the engine-ECU.

Q: Is the diagnosis code set?

YES : 

Troubleshoot the engine (Refer to GROUP 

13A 

− Diagnosis Code Chart .)

NO : 

Go to Step 3.

STEP 3. Check the M.U.T.-III Diagnosis code for 
other systems
Check if the diagnosis code No. U0100 is set to 
ETACS-ECU.

Q: Is the diagnosis code set?

YES : 

Go to Step 4.

NO : 

Go to Step 5.

STEP 4. Diagnosis code recheck
Check again if the diagnosis code is set to the combi-
nation meter.
(1) Erase the diagnosis code.

(2) Turn the ignition switch from the LOCK (OFF) 

position to the ON position.

(3) Check if the diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the engine-ECU.

NO : 

A poor connection, open circuit, or other 
intermittent malfunction in the CAN bus line 
between the combination meter and the 
engine-ECU. (Refer to GROUP 00 

− How to 

Use Troubleshooting/Inspection Service 
Points - How to Cope with Intermittent 
Malfunction .)

STEP 5. Diagnosis code recheck
Check again if the diagnosis code is set to the combi-
nation meter.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the LOCK (OFF) 

position to the ON position.

(3) Check if the diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the combination meter.

NO : 

A poor connection, open circuit, or other 
intermittent malfunction in the CAN bus line 
between the combination meter and the 
engine-ECU. (Refer to GROUP 00 

− How to 

Use Troubleshooting/Inspection Service 
Points - How to Cope with Intermittent 
Malfunction .)

Code No.U0141 ETACS CAN timeout

CAUTION

• If the diagnosis code No. U0141 is set, be sure 

to diagnose the CAN bus line.

• Before replacing the ECU or combination 

meter, ensure that the power supply circuit, 
the earth circuit and the communication cir-
cuit are normal.

• When the ETACS-ECU of vehicles without 

KOS is replaced, the encrypted code of the 
ignition key needs to be registered to the 
ETACS-ECU. (If the encrypted code is not reg-
istered, the engine cannot be started. Regis-
ter the encrypted code as described in 
Immobilizer System 

− How to Register Key ID 

P.54A-33

.)

DIAGNOSTIC FUNCTION

If the signal from ETACS-ECU cannot be received, 
the combination meter sets the diagnosis code No. 

U0141.

JUDGEMENT CRITERIA

With the ignition switch is at ON position, the diagno-
sis code No. U1190 is not stored and the diagnosis 
code No. U1195 is not stored, if the communication 
with ETACS-ECU cannot be established for 2500 ms 
or more, the combination meter determines that a 
problem has occurred.

PROBABLE CAUSES

• Malfunction of CAN bus line

• Malfunction of the combination meter

• Malfunction of the ETACS-ECU

COMBINATION METER

CHASSIS ELECTRICAL

54A-44

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.

Q: Is the check result normal?

YES : 

Go to Step 2.

NO : 

Repair the CAN bus line (Refer to GROUP 
54C 

− Troubleshooting ). Repair the CAN 

bus line and go to Step 5.

STEP 2. M.U.T.-III other system diagnosis code
Check if a diagnosis code, which relates to CAN 
communication-linked systems below, is set.
engine-ECU

• Code No.U0141: ETACS CAN timeout

Q: Is the diagnosis code set?

YES : 

Go to Step 3.

NO : 

Go to Step 4.

STEP 3. Check whether the diagnosis code is 
reset.
Recheck if the diagnosis code is set.
(1) Erase the diagnosis code.
(2) Turn the ignition switch to "ON" position.
(3) On completion, check that the diagnosis code is 

not reset.

Q: Is the diagnosis code set?

YES : 

Replace ETACS-ECU and then go to Step 

5.

NO : 

A poor connection, open circuit or other 
intermittent malfunction is present in the 
CAN bus lines between the ETACS-ECU 
and the combination meter (Refer to 
GROUP 00 

− How to use 

troubleshooting/Inspection Service Points ).

STEP 4. Check whether the diagnosis code is 
reset.
Recheck if the diagnosis code is set.
(1) Erase the diagnosis code.
(2) Turn the ignition switch to "ON" position.
(3) On completion, check that the diagnosis code is 

not reset.

Q: Is the diagnosis code set?

YES : 

Replace combination meter and then go to 

Step 5.

NO : 

A poor connection, open circuit or other 
intermittent malfunction is present in the 
CAN bus lines between the ETACS-ECU 
and the combination meter (Refer to 
GROUP 00 

− How to use 

troubleshooting/Inspection Service Points ).

STEP 5. Check whether the diagnosis code is 
reset.
Recheck if the diagnosis code is set.
(1) Erase the diagnosis code.
(2) Turn the ignition switch to "ON" position.
(3) On completion, check that the diagnosis code is 

not reset.

Q: Is the diagnosis code set?

YES : 

Go to Step 1.

NO : 

The procedure is complete.

Code No.U0164 A/C CAN timeout/Not equipped

CAUTION

• If the diagnosis code No. U0164 is set, be sure 

to diagnose the CAN bus line.

• Before replacing the ECU or combination 

meter, ensure that the power supply circuit, 
the earth circuit and the communication cir-
cuit are normal.

DIAGNOSTIC FUNCTION

If the signal from A/C-ECU cannot be received, the 
combination meter sets the diagnosis code No. 
U0164.

JUDGEMENT CRITERIA

With the ignition switch is at ON position, the diagno-
sis code No. U1190 is not stored and the diagnosis 
code No. U1195 is not stored, if the communication 
with A/C-ECU cannot be established for 2500 ms or 
more, the combination meter determines that a prob-
lem has occurred.

PROBABLE CAUSES

• Malfunction of CAN bus line

• Malfunction of the A/C-ECU

• Malfunction of combination meter

 

 

 

 

 

 

 

Content   ..  637  638  639  640   ..