Range Rover Body Repair Manual - part 9

 

  Index      Land Rover     Range Rover - Body Repair Manual 1996 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  7  8  9  10   ..

 

 

Range Rover Body Repair Manual - part 9

 

 

GENERAL SPECIFICATION DATA

9

SEALING AND CORROSION PROTECTION

APPLICATION EQUIPMENT

SATA Schutz Gun Model UBE

Specifications:
Air consumption

200 litres/min. (7cu/ft. min.) @ 45PSI

...............................................................

Weight

660grams (23.3oz)

..............................................................................

Manufactured and supplied by:
Sata Gmbh
Minden Industrial Ltd.
16 Greyfriars Road
Moreton Hall
Bury St. Edmunds
Suffolk IP32 7DX
Tel. (01284) 760791

The Sata Schutz Gun is approved for the re-treatment
of vehicle underbody areas with protective coatings as
supplied in 1-litre (1.76pt.), purpose-designed,
’one-way’ containers. The screw thread fitting (female
on the gun) will fit most Schutz-type packs.

Full operating details are supplied with the equipment.

NOTE: Always clean gun after use with the
appropriate solvent.

Sata HKD1 Wax Injection Equipment
The Sata HKD1 is approved by Rover for use in all
cavity wax re-treatment operations. The equipment
comprises a high quality forged gun with 1-litre
capacity pressure feed container, a flexible nylon
lance, 1100mm (43.3in.) straight steel lance and
hooked wand lance. A quick-change coupling is a
standard fitting to enable lances to be easily
interchanged. The lances each have their own spray
pattern characteristics to suit the type of box section
to be treated.

The Sata HKD1 is covered by a 12 month warranty.
All replacement parts and service are obtainable from
the suppliers.

04

GENERAL SPECIFICATION DATA

NEW RANGE ROVER

10

SEALING AND CORROSION PROTECTION

Cooper Pegler Falcon Junior Pneumatic (Airless)
Manufacturer and supplier:
Cooper Pegler & Co. Ltd.
Burgess Hill
Sussex RH15 9LA
Tel. 04 446 42526

Intended primarily for applying transit wax, the Falcon
Junior pneumatic sprayer has a 5-litre (1 gal.)
container with integral hand pump. This high quality
unit provides a simple and effective means of wax
spraying without the need for compressed air or
additional services.

A selection of nozzles, lances and hoses together with
a trigger valve assembly incorporating a filter enable
the sprayer to be used in a variety of applications.
These include general maintenance, wax injection and
paint application. All parts are fully replaceable and
include a wide range of nozzle configurations.

The Falcon Junior is fitted with Viton seals and is
guaranteed for 12 months.

3M Application Equipment
Manufacturer:
3M UK PLC
Automotive Trades Group
3M House
PO Box 1
Market Place
Bracknell
Berks. RG12 1JU
Tel. (01344) 858611

All 3M equipment is available from local trade factors
or 3M refinishing factors.

3M Caulking Gun 08002
A lightweight, robust metal skeleton gun designed to
accommodate 325mm (12.8in.) cartridge for
dispensing sealants etc. This gun facilitates rapid
cartridge loading and features a quick-release lever
for accurate material ejection and cut-off control.

3M Pneumatic Cartridge Gun 08012
An air line fed gun for application of 3M cartridge
products. Excellent ease of application for a smooth
sealant bead, and incorporates a regulator valve for
additional control.

Other 3m applicator equipment available:

3M Pneumatic Applicator Guns
Air line fed gun for application of 3M sachet sealers
(Part No. 08006 for 200ml [6fl/oz.] and 310ml [9fl/oz.]
sachets, and Part No. 08007 for all size sachets
including 600ml [18fl/oz.]).

3M Applicator Gun 08190
For application of 3M Structural Adhesive 08120.

3M Inner Cavity Wax Applicator Gun
Features 750mm (29.6in.) flexible tube and using
1-litre (1.76pt.) canisters, this approved equipment is
available from all 3M refinishing factors.

Other 3m applicator equipment available:

Heavy Duty Manual Gun.

GENERAL SPECIFICATION DATA

11

SEALING AND CORROSION PROTECTION

MATERIALS GUIDE

3M Automotive Structural Adhesive 08120
a two-part epoxy structural adhesive, with ’automix’
twin-cartridge dispenser. For doorskin and for bonding
panel stiffeners. Supplied as twin pack for use in small
trigger gun (No. 08190).

3M Bolted Panel Sealer 08572
Preformed strip 20mm (0.8in.) wide x 2mm (0.08in.)
thick supplied in 4.6 metre (81.2in.) reels.
Permanently flexible with good adhesion, for sealing
wing to body joints and other bolted or riveted panels.

3M Body Caulking 08568
Thumb-applied sealing compound supplied in
60-packs of preformed strips 300mm (11.8in.) long x
6mm (0.24in.) wide. For sealing large openings and
fissures. Non-hardening, does not dry out or crack,
can be overpainted immediately.

3M Drip-Chek Sealer Heavy 08531

For use on vertical fissures and seams up to 3mm
(0.12in.) wide for a firm but flexible seal which will not
harden or shrink. Self-levelling, will not sag on vertical
surfaces. May be worked with a tool or smoothed with
a wet finger.

Supplied in 150ml (4.5fl/oz.) tubes.

3M Drip-Chek Sealer Clear 08401
An easily flowing sealer similar to Drip-Chek Heavy
but of clear consistency. Ideal for an almost invisible
spot weal over finished paintwork. Can be overpainted
or even mixed with paint colour to form a self-coloured
sealant.

Supplied in 150ml (4.5fl/oz.) tubes.

3M Super Seam Sealer 08537
A brushable sealer designed to simulate original
factory-applied sealer on all overlap joints such as
floor pans, wheel arches, boot and load space seams
and fuel filler cap surrounds. Resistant to oil, petrol
and water. Should be brushed on in ONE direction
only for best results.

WARNING: Must be stored under
conditions applicable to highly flammable
materials.

3M Flexseal 08684, 08689 AND 08694
A high solid, non-shrinking, polyurethane body sealer
for use in either a hand gun or pneumatic applicator
gun. Excellent adhesion and sealing properties.
Resistant to oil, petrol and water. Supplied in 310ml
(9fl/oz.) cartridges and in a choice of black, white or
grey.

3M Polyurethane Sachet Sealer 08703, 08783,
08788
Similar to Flexseal polyurethane but available in
collapsible foil sachets in 310ml (9fl/oz.) and 600ml
(18fl/oz.) sizes with a choice of three colours: black,
grey or white.

3M Windscreen Sealer 08509
Non-hardening sealant for dry-glazed,
weatherstrip-type windscreens. Applied with applicator
gun.

Supplied in 310ml (9fl/oz.) cartridges.

3M Spray Schutz 08877, Body Schutz 08861
Flexible, rubberised, fast-drying coating which dries to
a black textured finish.

Spray Schutz supplied in 600ml (18fl/oz.) aerosols.
Spray Schutz and Body Schutz also supplied in 1-litre
(1.76pt.) cartridges to fit Schutz Gun.

04

GENERAL SPECIFICATION DATA

NEW RANGE ROVER

12

SEALING AND CORROSION PROTECTION

3M Flexible Parts Repair Material 05900
A fast-curing, two-part system for repairing minor
damage to plastic bumpers, spoilers, valances etc.
Dries in 30 mins.

Supplied as two-pack 320ml (10fl/oz.) kit.

3M Weld Thru’ SEALER 08625
For anti-corrosion protection between spot welded
panels. Brush application.

Supplied in 1-litre (1.76pt.) canisters.

3M Bodygard
Rubber-based, stone chip protective coating for
panels. Fast drying, low bake compatible and may be
overpainted. Varying textures obtainable depending
on type of finish required. Available in black (1-litre
[1.76pt.] pack 08858, aerosol 08158) or grey (1-litre
[1.76pt.] pack 08859, aerosol 08159).

3M Inner Cavity Wax
For protective coating on inner panels. Excellent
anti-corrosion properties. Available in transparent or
amber consistencies, and 1-litre (1.76pt.) canister or
500ml (0.88pt.) aerosol packs.

3M Zinc Spray 09113
Anti-corrosive coating for spot welding applications on
joints and seams. Supplied in 500ml (0.88pt.) aerosol
packs.

3M Waterproof Cloth Tape YS3998
Black waterproof tape for sealing door apertures and
body box section access holes. Long-lasting,
moisture-resistant adhesive will withstand immersion
in water.

Supplied in 50-metre (164.2ft.) rolls in a variety of
widths.

3M Adhesive Cleaner and Wax Remover 08984
For surface preparation before application of most
types of adhesive, coating and sealant, also for
removal of tar, silicone polish, wax, grease and oil.
Non-staining. May also be used for cleaning adhesive
remnants from sander disc backing pads.

Supplied in 1-litre (1.76pt.) canisters.

 

 

 

 

 

 

 

Content   ..  7  8  9  10   ..