Content .. 11 12 13 14 ..

Frelander 2. Manual - part 13

DTC

Description

Possible Cause

Action

B1A07-49 Speaker #7

Internal electronic
failure

Install a new module, refer to the new module/component
installation note at the top of the DTC Index

B1A08-11 Speaker #8

Rear Right Surround
Speaker circuit - short
to ground

Refer to electrical circuit diagrams and check Rear Right
Surround Speaker circuit for short to ground

B1A08-12 Speaker #8

Rear Right Surround
Speaker circuit - short
to power

Refer to electrical circuit diagrams and check Rear Right
Surround Speaker circuit for short to power

B1A08-13 Speaker #8

Rear Right Surround
Speaker circuit - open
circuit

Refer to electrical circuit diagrams and check Rear Right
Surround Speaker circuit for open circuit

B1A08-1A Speaker #8

Rear Right Surround
Speaker circuit -
resistance below
threshold

Refer to electrical circuit diagrams and check Rear right
surround speaker connection for crossload

B1A08-49 Speaker #8

Internal electronic
failure

Install a new module, refer to the new module/component
installation note at the top of the DTC Index

B1A09-11 Speaker #9

Center Speaker circuit -
short to ground

Refer to electrical circuit diagrams and check Center Speaker
circuit for short to ground

B1A09-12 Speaker #9

Center Speaker circuit -
short to power

Refer to electrical circuit diagrams and check Center Speaker
circuit for short to power

B1A09-13 Speaker #9

Center Speaker circuit -
open circuit

Refer to electrical circuit diagrams and check Center Speaker
circuit for open circuit

B1A09-1A Speaker #9

Center Speaker circuit -
resistance below
threshold

Refer to electrical circuit diagrams and check Center speaker
connection for crossload

B1A09-49 Speaker #9

Internal electronic
failure

Install a new module, refer to the new module/component
installation note at the top of the DTC Index

B1A10-11 Speaker #10

Left Subwoofer Speaker
circuit - short to
ground

Refer to electrical circuit diagrams and check Left Subwoofer
Speaker circuit for short to ground

B1A10-12 Speaker #10

Left Subwoofer Speaker
circuit - short to power

Refer to electrical circuit diagrams and check Left Subwoofer
Speaker circuit for short to power

B1A10-13 Speaker #10

Left Subwoofer Speaker
circuit - open circuit

Refer to electrical circuit diagrams and check Left Subwoofer
Speaker circuit for open circuit

B1A10-1A Speaker #10

Left Subwoofer Speaker
circuit - resistance
below threshold

Refer to electrical circuit diagrams and check Left subwoofer
speaker connection for crossload

B1A10-49 Speaker #10

Internal electronic
failure

Install a new module, refer to the new module/component
installation note at the top of the DTC Index

B1A11-11 Speaker #11

Right Subwoofer
Speaker circuit - short
to ground

Refer to electrical circuit diagrams and check Right Subwoofer
Speaker circuit for short to ground

B1A11-12 Speaker #11

Right Subwoofer
Speaker circuit - short
to power

Refer to electrical circuit diagrams and check Right Subwoofer
Speaker circuit for short to power

B1A11-13 Speaker #11

Right Subwoofer
Speaker circuit - open
circuit

Refer to electrical circuit diagrams and check Right Subwoofer
Speaker circuit for open circuit

B1A11-1A Speaker #11

Right Subwoofer
Speaker circuit -
resistance below
threshold

Refer to electrical circuit diagrams and check Right subwoofer
speaker connection for crossload

B1A11-49 Speaker #11

Internal electronic
failure

Install a new module, refer to the new module/component
installation note at the top of the DTC Index

B1D84-11 Headphone panel

Headphone panel 1 left
or right signal circuit -
short to ground

Refer to electrical circuit diagrams and check headphone panel
1 left or right signal circuit for short to ground

B1D84-13 Headphone panel

Headphone panel 1 left
or right signal circuit -
open circuit

Refer to electrical circuit diagrams and check headphone panel
1 left or right signal circuit for open circuit

DTC

Description

Possible Cause

Action

B1D84-23 Headphone panel

Headphone panel 1
control line circuit -
signal stuck low

Refer to electrical circuit diagrams and check headphone panel
1 control line for short to ground. Check for stuck switch/button

B1D85-11 Headphone panel

Headphone panel 2 left
or right signal circuit -
short to ground

Refer to electrical circuit diagrams and check headphone panel
2 left or right signal circuit for short to ground

B1D85-13 Headphone panel

Headphone panel 2 left
or right signal circuit -
open circuit

Refer to electrical circuit diagrams and check headphone panel
2 left or right signal circuit for open circuit

B1D85-23 Headphone panel

Headphone panel 2
control line circuit -
signal stuck low

Refer to electrical circuit diagrams and check headphone panel
2 control line for short to ground. Check for stuck switch/button

B1D86-11 Headphone panel

Headphone panel 3 left
or right signal circuit -
short to ground

Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system

B1D86-13 Headphone panel

Headphone panel 3 left
or right signal circuit -
open circuit

Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system

B1D86-23 Headphone panel

Headphone panel 3
control line circuit -
signal stuck low

Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system

B1D87-11 Headphone panel

Headphone panel 4 left
or right signal circuit -
short to ground

Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system

B1D87-13 Headphone panel

Headphone panel 4 left
or right signal circuit -
open circuit

Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system

B1D87-23 Headphone panel

Headphone panel 4
control line circuit -
signal stuck low

Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system

U3000-05 Control module -

system
programming
failures

Software
incompatibility
The version of the
Local Configuration file
does not match that
expected

Re-configure the audio amplifier as an existing control module,
using the manufacturer approved diagnostic system

U3000-42 Control module -

general memory
failure

General memory failure Re-configure the audio amplifier as an existing control module,

using the manufacturer approved diagnostic system. Clear DTC,
cycle ignition and read DTCs. If DTC returns, suspect audio
amplifier module and install a new module. Refer to the new
module/component installation note at the top of the DTC
Index

U3000-44 Control module -

data memory
failure

Data memory failure

Re-configure the audio amplifier as an existing control module,
using the manufacturer approved diagnostic system. Clear DTC,
cycle ignition and read DTCs. If DTC returns, suspect audio
amplifier module and install a new module. Refer to the new
module/component installation note at the top of the DTC
Index

U3000-55 Control Module

Incorrect car
configuration data
received

Check/up-date Car Configuration File using manufacturer
approved diagnostic system

U3000-87 Control Module

Missing message

Check CJB for DTCs and refer to DTC Index.
For additional information, refer to:

Communications Network

(418-00 Module Communications Network, Diagnosis and
Testing).
Check information and entertainment module for Car
Configuration File and MOST network DTCs and refer to relevant
DTC Index. Carry out MOST/CAN network tests using the
manufacturer approved diagnostic system

U3003-16 Battery Voltage

Circuit voltage below
threshold

Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system

U3003-17 Battery Voltage

Circuit voltage above
threshold

Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system

General Information - Diagnostic Trouble Code (DTC) IndexDTC: Anti-Lock
Braking System (ABS)

Description and Operation

• NOTE: If a control module or component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, before
the replacement of a component.

• NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan
tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).

• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal
places, and with an up-to-date calibration certificate. W hen testing resistance always take the resistance of the DMM
leads into account.

• NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.

• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.

• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may
be the cause. Always check for loose connections and corroded terminals.

Description And Operation

For a detailed description of the anti lock breaking system, refer to the relevant Description and Operation section in the
workshop manual.
For additional information, refer to:

Anti-Lock Control - Stability Assist

(206-09C Anti-Lock Control - Stability Assist,

Description and Operation).

DTC

Description

Possible Cause

Action

B10DF-46 Master cylinder isolation

valve - calibration /
parameter memory failure

Valve not calibrated

- Internal ABS
module failure

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C0001-01 Master Cylinder Isolation

Valve 1 - electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C0002-01 Master Cylinder Isolation

Valve 2 - electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C0003-01 Low Pressure Feed Valve 1

- electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C0004-01 Low Pressure Feed Valve 2

- electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C0010-01 Left Front Inlet Control -

General electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C0011-01 Left Front Outlet Control -

General electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C0014-01 Right Front Inlet Control -

General electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C0015-01 Right Front Outlet Control -

General electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C0018-01 Left Rear Inlet Control -

General electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

DTC

Description

Possible Cause

Action

C0019-01 Left Rear Outlet Control -

General electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C001C-01 Right Rear Inlet Control -

General electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C001D-01 Right Rear Outlet Control -

General electrical failure

Internal ABS module
fault

Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index

C0020-01 ABS Pump Motor Control -

General electrical failure

Power supply to
pump motor - short
circuit
Power supply to
pump motor -
incorrect voltage
Pump ground circuit
fault
Mechanical pump
fault

Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new ABS module. Refer to the new
module/component installation note at the top
of the DTC Index

C0020-1C ABS Pump Motor Control -

Circuit voltage out of range

Power supply to
pump motor - short
circuit, high
resistance
Pump ground circuit
fault
Internal ABS module
fault

C0020-71 ABS pump motor control -

actuator stuck

Power supply to
pump motor - short
circuit, high
resistance
Mechanical pump
fault

C0030-07 Left Front Tone Wheel -

Mechanical Failure

Bearing encoder
damaged

Install a new left front wheel bearing.
For additional information, refer to:

Front Wheel

Bearing

(204-01 Front Suspension, Removal and

Installation).

C0031-01 Left Front W heel Speed

Sensor - General electrical
failure

Wheel speed sensor
circuit - short to
ground, short to
power, open circuit
Wheel speed sensor
failure

Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new wheel speed sensor as required.
For additional information, refer to:

Front Wheel

Speed Sensor

(206-09A Anti-Lock Control,

Removal and Installation).

C0031-07 Left Front W heel Speed

Sensor - Mechanical Failure

Wheel speed sensor
faulty/incorrectly
installed

Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Check sensor for correct installation. Install a
new wheel speed sensor as required.
For additional information, refer to:

Front Wheel

Speed Sensor

(206-09A Anti-Lock Control,

Removal and Installation).

C0033-07 Right Front Tone Wheel -

Mechanical Failure

Bearing encoder
damaged

Install a new right front wheel bearing.
For additional information, refer to:

Front Wheel

Bearing

(204-01 Front Suspension, Removal and

Installation).

C0034-01 Right Front Wheel Speed

Sensor - General electrical
failure

Wheel speed sensor
circuit - short to
ground, short to
power, open circuit
Wheel speed sensor
failure

Front Wheel

Speed Sensor

(206-09A Anti-Lock Control,

Removal and Installation).

C0034-07 Right Front Wheel Speed

Sensor - Mechanical Failure

Wheel speed sensor
faulty/incorrectly
installed

Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check sensor for correct installation.
Clear DTC and retest if DTC returns. Install a
new wheel speed sensor as required.
For additional information, refer to:

Front Wheel

Speed Sensor

(206-09A Anti-Lock Control,

Content .. 11 12 13 14 ..