Index Manuals Jeep Grand Cherokee (2023 year). Manual in english

Search copyright infringement

Content .. 1 2 ..

Jeep Grand Cherokee (2023 year). Manual in english - page 1

12

VEHICLE MODIFICATIONS/ALTERATIONS

SYMBOL GLOSSARY

Some car components have colored labels with symbols indicating

precautions to be observed when using this component. It is important to

follow all warnings when operating your vehicle. See below for the definition of

each symbol

NOTE:

Warning and Indicator lights are different based upon equipment options and

current vehicle status. Some telltales are optional and may not appear.

WARNING!

Any modifications or alterations to this vehicle could seriously affect its

roadworthiness and safety and may lead to a collision resulting in serious

injury or death.

Red Warning Lights

Active Driving Assist - Driver Inattentiveness Warning Light

Air Bag Warning Light

Brake Warning Light

Battery Charge Warning Light

Door Open Warning Light

Electric Power Steering (EPS) Fault Warning Light

Electronic Throttle Control (ETC) Warning Light

Engine Coolant Temperature Warning Light

Hood Open Warning Light

Liftgate Open Warning Light

Night Vision Animal Warning Light

Red Warning Lights

13

Night Vision Pedestrian Warning Light

Oil Pressure Warning Light

Oil Temperature Warning Light

Rear Seat Belt Reminder Warning Light

Seat Belt Reminder Warning Light

Transmission Temperature Warning Light

Vehicle Security Warning Light

Red Warning Lights

Yellow Warning Lights

Active Driving Assist - Driver Inattentiveness Warning Light

Active Driving Assist Fault Warning Light

Active Lane Management Warning Light

Air Suspension Fault Warning Light

Anti-Lock Brake System (ABS) Warning Light

Electric Park Brake Fault Warning Light

Electronic Stability Control (ESC) Active Warning Light

1

14

Electronic Stability Control (ESC) OFF Warning Light

Engine Check/Malfunction Indicator Warning Light (MIL)

Fuel Level Sensor Failure Warning Light

Low Fuel Warning Light

Low Washer Fluid Warning Light

Night Vision Animal Warning Light

Night Vision Pedestrian Warning Light

Yellow Warning Lights

Service 4WD Warning Light

Service Active Lane Management Warning Light

Service Adaptive Cruise Control (ACC) Warning Light

Service Forward Collision Warning (FCW) Or Pedestrian

Emergency Braking (PEB) Warning Light

Service Stop/Start System Warning Light

Sway Bar Fault Warning Light

Tire Pressure Monitoring System (TPMS) Warning Light

Yellow Warning Lights

15

Yellow Indicator Lights

4WD Low Indicator Light

Air Suspension Active Indicator Light

Air Suspension Aerodynamic Height Indicator Light

Air Suspension Entry/Exit Indicator Light

Air Suspension Off-Road 1 Indicator Light

Air Suspension Off-Road 2 Indicator Light

Auto HOLD! Fault Indicator Light

Forward Collision Warning (FCW) Or Pedestrian Emergency

Braking (PEB) OFF Indicator Light

Max Payload Exceeded Indicator Light

NEUTRAL Indicator Light

Sway Bar Indicator Light

Green Indicator Lights

Active Driving Assist - Driver Attentive Indicator Light

Active Lane Management Indicator Light

Yellow Indicator Lights

1

16

Adaptive Cruise Control (ACC) Set With Target Indicator Light

Adaptive Cruise Control (ACC) Set With No Target Detected

Indicator Light

Auto HOLD Indicator Light

Cruise Control SET Indicator Light

Front Fog Indicator Light

Night Vision Active Indicator Light

Green Indicator Lights

Parking/Headlights On Indicator Light

Rear Seat Belt Fastened Indicator Light

Selec-Speed Control Indicator Light

Sport Mode Indicator Light

Stop/Start Active Indicator Light

Turn Signal/Hazard Indicator Lights

Green Indicator Lights

17

White Indicator Lights

Active Driving Assist On Indicator Light

Adaptive Cruise Control (ACC) Ready Indicator Light

Cruise Control Ready Indicator Light

Hill Descent Control (HDC) Indicator Light

Rear Seat Unoccupied Indicator Light

Blue Indicator Lights

High Beam Indicator Light

Gray Indicator Lights

Night Vision Suppressed Indicator Light

1

18

GETTING TO KNOW YOUR VEHICLE

KEYS

K

EY

F

OB

Your vehicle is equipped with a key fob which

supports Passive Entry, Remote Keyless Entry

(RKE), Keyless Enter ‘n Go™ (if equipped), Remote

Start (if equipped), and remote power liftgate (if

equipped) operation. The key fob allows you to lock

or unlock all doors and liftgate, as well as activate

the Panic Alarm from distances up to

approximately 66 ft (20 m). The key fob does not

need to be pointed at the vehicle to activate the

system. The key fob also contains an emergency

key, which is stored in the rear of the key fob.

NOTE:

In vehicles equipped with Remote Start, the key

fob will operate at distances up to 328 ft (100 m).

NOTE:



The key fob’s wireless signal may be blocked if

the key fob is located next to a mobile phone,

laptop, or other electronic device. This may

result in poor performance.



If your vehicle is equipped with a Wireless

Charging Pad, the key fob may not be detected

if it is placed within 6 inches (15 cm) of the pad



With the ignition in the ON position and the

vehicle moving at 2 mph (4 km/h), all RKE

commands are disabled.

Key Fob

In case the ignition switch does not change

positions with the push of a button, the key fob

may have a low or fully depleted battery. A low key

fob battery can be verified by referring to the

instrument cluster, which will display directions to

follow.
For more information on ignition positions, see

NOTE:

A low key fob battery condition may be indicated by

a message in the instrument cluster display, or by

the LED light on the key fob. If the LED key fob light

no longer illuminates after a key fob button is

pushed, then the key fob battery requires

replacement

To Lock/Unlock The Doors And Liftgate

Push and release the unlock button on the key fob

once to unlock the driver’s door, or twice within five

seconds to unlock all the doors and the liftgate. To

lock all the doors and the liftgate, push the lock

button once.
If enabled within the Uconnect system, the turn

signals will flash and other illuminated entry

features will be activated when the doors are

unlocked. When the doors are locked, the turn

signals will flash and the horn will chirp.

1 — LED Indicator
2 — Unlock
3 — Lock
4 — Remote Start
5 — Power Liftgate
6 — Panic
7 — Emergency Key

GETTING TO KNOW YOUR VEHICLE

19

NOTE:



If the vehicle is equipped with the Auto Relock

feature, and is unlocked with the key fob, and

no door is opened within 60 seconds, the

vehicle will relock and the Vehicle Security

system will arm (if equipped). This feature can

be enabled/disabled within Uconnect Settings.



If one or more doors are open, or the liftgate is

open, the doors will lock. The doors will unlock

again automatically if the key fob is left inside

the passenger compartment, otherwise the

doors will stay locked.

All doors can be programmed to unlock on the first

push of the unlock button through Uconnect

Settings

Using The Panic Feature

To turn the Panic feature on or off, push the Panic

button on the key fob. When the Panic feature is

activated, the turn signals will flash, the horn may

pulse on and off (if equipped with horn alarm), and

the interior lights will turn on.
The Panic feature will stay on for three minutes

unless you turn it off by either pushing the Panic

button a second time or drive the vehicle at a

speed of 15 mph (24 km/h) or greater.

NOTE:



The interior lights will turn off if you place the

ignition in the ON/RUN position while the Panic

feature is activated. However, the exterior lights

and horn (if equipped with horn alarm) will

remain on.



You may need to be closer than 66 ft (20 m)

from the vehicle when using the key fob to turn

off the Panic feature due to the radio frequency

noises emitted by the system.

Key Left Vehicle Feature

If a valid key fob is no longer detected inside the

vehicle while the vehicle’s ignition system is in the

ON/RUN or START position, the message “Key Fob

Has Left The Vehicle” will be shown in the

instrument cluster display along with an interior

chime. An exterior audible and visual alert will also

be activated to warn the driver.
The vehicle’s horn will rapidly chirp three times

along with a single flash of the vehicle’s exterior

lights.

NOTE:



The doors have to be open and then closed in

order for the vehicle to check for the presence of

a key fob; the Key Left Vehicle feature will not

activate until all of the doors are closed.



These alerts will not be activated in situations

where the vehicle’s engine is left running with

the key fob inside.

Using The Key Fob To Open Vehicle

Windows — If Equipped

From outside of the vehicle, push and release the

unlock button on the key fob, and within five

seconds push and hold the unlock button for up to

seven seconds. All vehicle door windows will open.

NOTE:



This feature is enabled through Uconnect

Settings



Vehicle must be equipped with front and rear

auto up/down windows.

Replacing The Battery In The Key Fob

The replacement battery model is one CR2450

battery.

NOTE:



Customers are recommended to use a battery

obtained from Mopar®. Aftermarket coin

battery specifications may not meet the original

OEM coin battery specifications.



Perchlorate Material — special handling may

apply. See

www.dtsc.ca.gov/hazard

ouswaste/perchlorate

for further information.



Do not touch the battery terminals that are on

the back housing or the printed circuit board.

2

20

GETTING TO KNOW YOUR VEHICLE



Do not replace the coin battery if the LED on the

key fob above the top row buttons blinks when

a button is pressed. The coin battery should last

a minimum of three years with normal vehicle

usage.

1. Remove the emergency key (2) by pushing

the emergency key release button (1) on the

side of the key fob, and pulling the emergency

key out with the other hand.

Emergency Key Removal

Emergency Key Removed

2. Hold the key fob with the button side facing

down, and locate the small rectangular gap on

the left side between the housing and the back

cover of the key fob. Use a small flat-bladed

tool to pry apart the two halves of the key fob.

Make sure not to damage the seal during

removal.

Pry Apart Key Fob Halves

3. Next, locate the gap on the right side of the key

fob, which is positioned farther to the edge

than the left side gap. Pry open the right side,

and remove the back cover.

4. Remove the battery by using your thumb to

slide the battery downward and back toward

the key ring.

Key Fob Battery Location

NOTE:

You can also insert a screwdriver or similar tool

into the battery removal pocket to pry the battery

out.

1 — Emergency Key Release Button
2 — Emergency Key

GETTING TO KNOW YOUR VEHICLE

21

Battery Removal Pocket

NOTE:

When replacing the battery, ensure the (+) sign on

the battery is facing upward. Avoid touching the

new battery with your fingers. Skin oils may cause

battery deterioration. If you touch a battery, clean

it with rubbing alcohol.
5. Replace the battery by using your thumb to

push down and slide the battery under the

small lip on the top edge of the opening.

Key Fob Battery Replacement

6. To assemble the key fob case, line up the top

edge of the back cover with the top of the fob,

and press the edges into the interlocking

hinges until all edges snap together with no

large visual gaps.

7. Reinsert the emergency key until it locks into

place.

NOTE:

The key fob battery should only be replaced by

qualified technicians. If the battery requires

replacement, see an authorized dealer.

Programming And Requesting Additional

Key Fobs

Programming the key fob may be performed by an

authorized dealer.

NOTE:



Once a key fob is programmed to a vehicle, it

cannot be repurposed and reprogrammed to

another vehicle.



Only key fobs that are programmed to the

vehicle electronics can be used to start and

operate the vehicle. Once a key fob is

programmed to a vehicle, it cannot be

programmed to any other vehicle.

WARNING!



The integrated key fob contains a coin cell

battery. Do not ingest the battery; there is a

chemical burn hazard. If the coin cell battery is

swallowed, it can cause severe internal burns

in just two hours and can lead to death.



If you think a battery may have been swal

-

lowed or placed inside any part of the body,

seek immediate medical attention.



Keep new and used batteries away from chil

-

dren. If the battery compartment does not

close securely, stop using the product and

keep it away from children.

2

22

GETTING TO KNOW YOUR VEHICLE

Duplication of key fobs may be performed at an

authorized dealer. This procedure consists of

programming a blank key fob to the vehicle

electronics. A blank key fob is one that has never

been programmed.

NOTE:



When having the Sentry Key Immobilizer system

serviced, bring all vehicle keys with you to an

authorized dealer.



Keys must be ordered to the correct key cut to

match the vehicle locks.

SENTRY KEY

The Sentry Key Immobilizer system prevents

unauthorized vehicle operation by disabling the

engine. The system does not need to be armed or

activated. Operation is automatic, regardless of

whether the vehicle is locked or unlocked.

The system uses a key fob, keyless push button

ignition and a Radio Frequency (RF) receiver to

prevent unauthorized vehicle operation. Therefore,

only key fobs that are programmed to the vehicle

can be used to start and operate the vehicle. The

system cannot reprogram a key fob obtained from

another vehicle.
After placing the ignition in the ON/RUN position,

the Vehicle Security Light will turn on for three

seconds for a bulb check. If the light remains on

after the bulb check, it indicates that there is a

problem with the electronics. In addition, if the light

begins to flash after the bulb check, it indicates

that someone attempted to start the engine with

an invalid key fob. In the event that a valid key fob

is used to start the engine but there is an issue

with the vehicle electronics, the engine will start

and shut off after two seconds.
If the Vehicle Security Light turns on during normal

vehicle operation (vehicle running for longer than

10 seconds), it indicates that there is a fault in the

electronics. Should this occur, have the vehicle

serviced as soon as possible by an authorized

dealer.

All of the key fobs provided with your new vehicle

have been programmed to the vehicle electronics

NOTE:

A key fob that has not been programmed is also

considered an invalid key.

IGNITION SWITCH

K

EYLESS

E

NTER

‘

N

G

O

™ I

GNITION

This feature allows the driver to operate the

ignition switch with the push of a button as long as

the key fob is in the passenger compartment.
The START/STOP ignition button has several

operating modes that are labeled and will

illuminate when in position. These modes are OFF,

ON/RUN, and START.

WARNING!



Always remove the key fobs from the vehicle

and lock all doors when leaving the vehicle

unattended.



Always remember to place the Keyless

Enter ‘n Go™ Ignition in the OFF position when

exiting the vehicle.

CAUTION!

The Sentry Key Immobilizer system is not

compatible with some aftermarket remote

starting systems. Use of these systems may

result in vehicle starting problems and loss of

security protection.

GETTING TO KNOW YOUR VEHICLE

23

START/STOP Ignition Button

The push button ignition can be placed in the

following modes:
OFF



The engine is stopped



Some electrical devices (e.g. power locks,

alarm, etc.) are still available

ON/RUN



Driving position



All electrical devices are available (e.g. climate

controls, heated seats, etc.)

START



The engine will start (when foot is on the brake

pedal)

NOTE:



If the ignition position does not change with a

push of the ignition button, and the instrument

cluster displays a message such as “Key Fob

Not Detected”, the key fob may have a low or

depleted battery. In this situation, a backup

method can be used to operate the ignition

switch. Put the nose side of the key fob (side

opposite of the emergency key) against the

START/STOP ignition button and push to

operate the ignition switch.



Replacement of the key fob battery is recom

-

mended.

Depleted Key Fob Battery Procedure

1 — OFF
2 — ON/RUN

WARNING!



When exiting the vehicle, always place the

ignition in the OFF position, remove the key

fob from the vehicle, and lock your vehicle.



Never leave children alone in a vehicle, or with

access to an unlocked vehicle.



Allowing children to be in a vehicle unattended

is dangerous for a number of reasons. A child

or others could be seriously or fatally injured.

Children should be warned not to touch the

parking brake, brake pedal or the gear

selector.



Do not leave the key fob in or near the vehicle,

or in a location accessible to children, and do

not leave Keyless Enter ‘n Go™ Ignition in the

ON/RUN position. A child could operate power

windows, other controls, or move the vehicle.



Do not leave children or animals inside parked

vehicles in hot weather. Interior heat buildup

may cause serious injury or death.

CAUTION!

An unlocked vehicle is an invitation for thieves.

Always remove key fob from the vehicle and lock

all doors when leaving the vehicle unattended.

2

24

GETTING TO KNOW YOUR VEHICLE

NOTE:



The key fob may not be detected by the vehicle

Keyless Enter ‘n Go™ system if it is located next

to a mobile phone, laptop or other electronic

device, or in the cupholders near aluminum

cans; these devices may block the key fob’s

wireless signal and prevent the Keyless Enter ‘n

Go™ system from starting the vehicle.



For more information on the engine starting

procedure, see



When opening the driver's door and the ignition

is in the ON/RUN position (engine not running),

a chime will sound to remind you to place the

ignition in the OFF position. In addition to the

chime, the message “Ignition ON” will display in

the cluster.

REMOTE START — IF EQUIPPED

This system uses the key fob to start the

engine conveniently from outside the

vehicle while still maintaining security.

The system has a range of approximately

328 ft (100 m).
Remote Start is used to defrost windows in cold

weather, and to reach a comfortable climate in all

ambient conditions before the driver enters the

vehicle.

NOTE:

Obstructions between the vehicle and key fob may

reduce this range

H

OW

T

O

U

SE

R

EMOTE

S

TART

Push and release the Remote Start button on the

key fob twice within five seconds. The vehicle

doors will lock, the parking lights will flash, and the

horn will chirp twice (if programmed). Then, the

engine will start, and the vehicle will remain in the

Remote Start mode for a 15 minute cycle. Pushing

the Remote Start button a third time shuts the

engine off.

NOTE:



If the Remote Start button on the key fob is

pushed too rapidly during activation, the vehicle

may not start.



With Remote Start, the engine will only run for

15 minutes.



Remote Start can only be used twice.



If an engine fault is present or fuel level is low,

the vehicle will start and then shut down in 10

seconds.



The parking lights will turn on and remain on

during Remote Start mode.



Headlight animation (if equipped) will occur

when Remote Start is activated, if “Headlight

Illumination On Approach” is enabled within

Uconnect Settings.



For security, power window and power sunroof

operation (if equipped) are disabled when the

vehicle is in the Remote Start mode.



The ignition must be placed in the ON/RUN posi

-

tion before the Remote Start sequence can be

repeated for a third cycle.

WARNING!



Do not start or run an engine in a closed

garage or confined area. Exhaust gas contains

carbon monoxide (CO) which is odorless and

colorless. Carbon monoxide is poisonous and

can cause serious injury or death when

inhaled.



Keep key fobs away from children. Operation

of the Remote Start system, windows, door

locks or other controls could cause serious

injury or death.

GETTING TO KNOW YOUR VEHICLE

25

(Continued)

All of the following conditions must be met before

the engine will remote start:



Gear selector in PARK



Doors closed



Hood closed



Liftgate closed



Hazard switch off



Brake switch inactive (brake pedal not pressed)



Battery at an acceptable charge level



System not disabled from previous Remote

Start event



Vehicle Security Light is flashing



Ignition in OFF position



Fuel level meets minimum requirement



Vehicle Security system is not signaling an intru

-

sion



Malfunction Indicator Light is not illuminated

T

O

E

XIT

R

EMOTE

S

TART

M

ODE

To drive the vehicle after starting the Remote Start

system, either push and release the unlock button

on the key fob to unlock the doors, or unlock the

vehicle using Keyless Enter ‘n Go™ — Passive Entry

via the door handles, and disarm the Vehicle

Security system (if equipped). Then, prior to the

end of the 15 minute cycle, push and release the

START/STOP ignition button.
The Remote Start system will turn the engine off if

the Remote Start button on the key fob is pushed

again, or if the engine is allowed to run for the

entire 15 minute cycle. Once the ignition is placed

in the ON/RUN position, the climate controls will

resume the previously set operations

(temperature, blower control, etc.).

NOTE:



To avoid unintentional shutdowns, the system

will disable for two seconds after receiving a

valid Remote Start request.



For vehicles equipped with the Keyless

Enter ‘n Go™ — Passive Entry feature, the message

“Remote Start Active — Push Start Button” will

display in the instrument cluster display until you

push the START/STOP ignition button.

R

EMOTE

S

TART

F

RONT

D

EFROST

A

CTIVATION

— I

F

E

QUIPPED

When Remote Start is active, and the outside

ambient temperature is 40°F (4.5°C) or below, the

system will automatically activate front defrost for

15 minutes or less. The timing is dependent on the

ambient temperature. Once the timer expires, the

system will automatically adjust the settings

depending on ambient conditions. See “Remote

Start Comfort Systems — If Equipped” in the next

section for detailed operation.

R

EMOTE

S

TART

C

OMFORT

S

YSTEMS

—

I

F

E

QUIPPED

When Remote Start is activated, the front and rear

defrost will automatically turn on in cold weather. The

heated steering wheel and driver heated seat feature

will turn on if selected in the Comfort menu screen

within Uconnect Settings

page 204. In warm

weather, the driver vented seat feature will

automatically turn on when Remote Start is activated,

if programmed in the Comfort menu screen. The

vehicle will adjust the climate control settings

depending on the outside ambient temperature.

WARNING!



Do not start or run an engine in a closed

garage or confined area. Exhaust gas contains

carbon monoxide (CO) which is odorless and

colorless. Carbon monoxide is poisonous and

can cause serious injury or death when

inhaled.



Keep key fobs away from children. Operation

of the Remote Start system, windows, door

locks or other controls could cause serious

injury or death.

WARNING!

2

26

GETTING TO KNOW YOUR VEHICLE

Automatic Temperature Control (ATC)
The climate controls will automatically adjust to

the optimal temperature and mode settings

depending on the outside ambient temperature.

This will occur until the ignition is placed in the ON/

RUN position where the climate controls will

resume their previous settings.
For more information on ATC and climate control

settings, see

NOTE:

These features will stay on through the duration of

Remote Start until the ignition is placed in the ON/

RUN position. The climate control setting will

change, and exit automatic operation, if manually

adjusted by the driver while the vehicle is in

Remote Start mode. This includes the OFF button

on the climate controls, which will turn the system

off.

R

EMOTE

S

TART

W

INDSHIELD

W

IPER

D

E

-I

CER

A

CTIVATION

— I

F

E

QUIPPED

When Remote Start is active and the outside

ambient temperature is less than 33°F (0.6°C),

the Windshield Wiper De-Icer will activate. Exiting

Remote Start will resume its previous operation. If

the Windshield Wiper De-Icer was active, the timer

and operation will continue

R

EMOTE

S

TART

A

BORT

M

ESSAGE

One of the following messages will display in the

instrument cluster display if the vehicle fails to

remote start or exits Remote Start prematurely:



Remote Start Canceled — Door Open



Remote Start Canceled — Hood Open



Remote Start Canceled — Liftgate Open



Remote Start Canceled — Fuel Low



Remote Start Canceled — Time Expired



Remote Start Canceled — System Fault



Remote Start Disabled — Start Vehicle to Reset

The instrument cluster display message stays

active until the ignition is placed in the ON/RUN

position.

VEHICLE SECURITY SYSTEM — IF EQUIPPED

The Vehicle Security system monitors the vehicle

doors, hood, liftgate, and the Keyless Enter ‘n Go™

Ignition for unauthorized operation. While the

Vehicle Security system is armed, interior switches

for door locks and liftgate release handle are

disabled. If something triggers the alarm, the

Vehicle Security system will provide the following

audible and visible signals:



The horn will pulse



The turn signals will flash



The Vehicle Security Light in the instrument

cluster will flash

T

O

A

RM

T

HE

S

YSTEM

Follow these steps to arm the Vehicle Security

system:
1. Make sure the vehicle’s ignition is placed in

the OFF position.



Make sure the vehicle’s keyless ignition

system is OFF.

2. Perform one of the following methods to lock

the vehicle:



Push lock on the interior power door lock

switch with the driver and/or passenger

door open.



Push the lock button on the exterior Passive

Entry door handle with a valid key fob avail

-

able in the same exterior zone



Push the lock button on the key fob.

3. If any doors are open, close them.

GETTING TO KNOW YOUR VEHICLE

27

When the Vehicle Security system is armed, the

Vehicle Security Light (located in the lower right

portion of the instrument cluster display) will begin

to flash every two seconds until it is disarmed.

NOTE:

If the system is armed by pushing the lock button

on the interior door panel, the Vehicle Security

Light will flash rapidly for about 15 seconds once

the door is closed, then slow down to every two

seconds.

T

O

D

ISARM

T

HE

S

YSTEM

The Vehicle Security system can be disarmed using

any of the following methods:



Push the unlock button on the key fob.



Grab the Passive Entry door handle to unlock

the door



Cycle the ignition out of the OFF position to

disarm the system.

NOTE:



The driver's door key cylinder cannot arm or

disarm the Vehicle Security system. Use of the

door key cylinder when the alarm is armed will

sound the alarm when the door is opened.



The Vehicle Security system remains armed

when the power liftgate is opened using the lift

-

gate button on the key fob. If someone enters

the vehicle through the opened liftgate, then

opens any door from the inside, the alarm will

sound.



If Passive Entry (if equipped) is used to unlock

the liftgate, the Vehicle Security system is

disarmed and the rest of the vehicle doors will

remain locked unless all doors are set to unlock

on first press within Uconnect Settings.



When the Vehicle Security system is armed, the

interior power door lock switches will not unlock

the doors.

The Vehicle Security system is designed to protect

your vehicle. However, you can create conditions

where the system will give you a false alarm. If one

of the previously described arming sequences has

occurred, the Vehicle Security system will arm

regardless of whether you are in the vehicle or not.

If you remain in the vehicle and open a door, the

alarm will sound. If this occurs, disarm the Vehicle

Security system.
If the Vehicle Security system is armed and the

battery becomes disconnected, the Vehicle

Security system will remain armed when the

battery is reconnected; the exterior lights will flash,

and the horn will sound. If this occurs, disarm the

Vehicle Security system.

R

EARMING

O

F

T

HE

S

YSTEM

If something triggers the alarm and no action is

taken to disarm it, the Vehicle Security system will

turn the horn off after a 29 second cycle (with five

seconds between cycles and up to eight cycles if

the trigger remains active) and then rearm itself.

S

ECURITY

S

YSTEM

M

ANUAL

O

VERRIDE

The Vehicle Security system will not arm if you lock

the doors using the emergency lock lever

T

AMPER

A

LERT

If something has triggered the Vehicle Security

system in your absence, the horn will sound three

times and the exterior lights will blink three times

when you disarm the Vehicle Security system.

DOORS

M

ANUAL

D

OOR

L

OCKS

The front doors can be manually unlocked with a

single pull of the inside door handle. The driver’s

door can also be manually unlocked by inserting

the emergency key into the lock cylinder on the

outside door handle.

2

Content .. 1 2 ..

///////////////////////////////////////