Jeep Cherokee (2022 year). Manual in english - page 1

 

  Index      Manuals     Jeep Cherokee (2022 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..      1       2         ..

 

 

 

Jeep Cherokee (2022 year). Manual in english - page 1

 

 

9

SYMBOLS KEY

If you do not read this entire Owner’s Manual, you may miss important 

information. Observe all Cautions and Warnings.

ROLLOVER WARNING 

Utility vehicles have a significantly higher rollover rate than other types of 

vehicles. This vehicle has a higher ground clearance and a higher center of 

gravity than many passenger vehicles. It is capable of performing better in a 

wide variety of off-road applications. Driven in an unsafe manner, all vehicles 

can go out of control. Because of the higher center of gravity, if this vehicle is 

out of control it may roll over while some other vehicles may not.
Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions 

that can cause loss of vehicle control. Failure to operate this vehicle safely may 

result in a collision, rollover of the vehicle, and severe or fatal injury. Drive 

carefully.

Rollover Warning Label

Failure to use the driver and passenger seat belts provided is a major cause of 

severe or fatal injury. In fact, the US government notes that the universal use 

of existing seat belts could cut the highway death toll by 10,000 or more each 

year and could reduce disabling injuries by two million annually. In a rollover 

crash, an unbelted person is significantly more likely to die than a person 

wearing a seat belt. Always buckle up.

WARNING!

These statements are against operating 

procedures that could result in a collision, bodily 

injury and/or death.

CAUTION!

These statements are against procedures that 

could result in damage to your vehicle. 

NOTE:

A suggestion which will improve installation, 

operation, and reliability. If not followed, may 

result in damage.

TIP:

General ideas/solutions/suggestions on easier 

use of the product or functionality.

PAGE REFERENCE 

ARROW 

Follow this reference for additional information on 

a particular feature.

FOOTNOTE

Supplementary and relevant information 

pertaining to the topic. 

1

10  

VEHICLE MODIFICATIONS/ALTERATIONS 

SYMBOL GLOSSARY

Some car components have colored labels with symbols indicating 

precautions to be observed when using this component. It is important to 

follow all warnings when operating your vehicle. See below for the definition of 

each symbol  

Ú

page 80.

NOTE:

Warning and Indicator lights are different based upon equipment options and 

current vehicle status. Some telltales are optional and may not appear.

WARNING!

Any modifications or alterations to this vehicle could seriously affect its 

roadworthiness and safety and may lead to a collision resulting in serious 

injury or death.

Red Warning Lights

Seat Belt Reminder Warning Light

 

Ú

page 80

Air Bag Warning Light

 

Ú

page 80

Brake Warning Light

 

Ú

page 80

Battery Charge Warning Light

 

Ú

page 81

Door Open Warning Light

 

Ú

page 81

Electric Power Steering (EPS) Fault Warning Light

 

Ú

page 81

Electronic Throttle Control (ETC) Warning Light

 

Ú

page 82

Engine Coolant Temperature Warning Light

 

Ú

page 82

Hood Open Warning Light

 

Ú

page 82

Liftgate Open Warning Light

 

Ú

page 82

Oil Pressure Warning Light

 

Ú

page 82

Red Warning Lights

11

Oil Temperature Warning Light

 

Ú

page 83

Transmission Temperature Warning Light

 

Ú

page 83

Vehicle Security Warning Light

 

Ú

page 83

Yellow Warning Lights

Adaptive Cruise Control (ACC) Fault Warning Light

 

Ú

page 83

Electronic Park Brake Warning Light

 

Ú

page 83

Anti-Lock Brake System (ABS) Warning Light

 

Ú

page 83

Electronic Stability Control (ESC) Active Warning Light

 

Ú

page 83

Red Warning Lights

Electronic Stability Control (ESC) OFF Warning Light

 

Ú

page 84

Low Fuel Warning Light

 

Ú

page 84

Low Washer Fluid Warning Light

 

Ú

page 84

Service LaneSense Warning Light

 

Ú

page 84

LaneSense Warning Light

 

Ú

page 84

Engine Check/Malfunction Indicator Warning Light (MIL)

 

Ú

page 84

Service 4WD Warning Light

 

Ú

page 85

Service Forward Collision Warning (FCW) Light

 

Ú

page 85

Yellow Warning Lights

1

12  

Service Stop/Start System Warning Light

 

Ú

page 85

Cruise Control Fault Warning Light

 

Ú

page 85

Tire Pressure Monitoring System (TPMS) Warning Light

 

Ú

page 85

Yellow Indicator Lights

Forward Collision Warning (FCW) Off Indicator Light

 

Ú

page 86

4WD Low Indicator Light

 

Ú

page 86

Rear Axle Lock Indicator Light

 

Ú

page 86

Wait To Start Light

 

Ú

page 86

Yellow Warning Lights

Water In Fuel Indicator Light

 

Ú

page 86

Green Indicator Lights

Adaptive Cruise Control (ACC) Set With Target Vehicle Light

 

Ú

page 87

Adaptive Cruise Control (ACC) Set Without Target Vehicle Light

 

Ú

page 87

Cruise Control Set Indicator Light

 

Ú

page 87

Front Fog Indicator Light

 

Ú

page 87

LaneSense Indicator Light

 

Ú

page 87

Parking/Headlights On Indicator Light

 

Ú

page 87

Yellow Indicator Lights

13

Stop/Start Active Indicator Light

 

Ú

page 87

Turn Signal Indicator Lights

 

Ú

page 87

White Indicator Lights

Hill Descent Control (HDC) Indicator Light

 

Ú

page 87

LaneSense Indicator Light

 

Ú

page 88

Speed Warning Indicator Light

 

Ú

page 88

Green Indicator Lights

Selec-Speed Control Indicator Light

 

Ú

page 88

Cruise Control Ready Indicator Light

 

Ú

page 88

Blue Indicator Lights

High Beam Indicator Light

 

Ú

page 88

White Indicator Lights

1

14  

GETTING TO KNOW YOUR VEHICLE

KEYS 

K

EY

 F

OB

Your vehicle may be equipped with a standard 

ignition key fob or a keyless ignition key fob.
The standard ignition key fob operates the ignition 

switch. Insert the square end of the key fob into the 

ignition switch located on the instrument panel 

and rotate to the desired position. The key fob also 

contains an emergency key, which is stored in the 

rear of the key fob.

Key Fob For Standard Ignition

Your vehicle may be equipped with a keyless 

ignition key fob that supports Passive Entry, 

Remote Keyless Entry (RKE), Keyless Enter ‘n Go™ 

(if equipped), Remote Start (if equipped), and 

power liftgate operation. This type of key fob 

operates a START/STOP ignition button system. 

This feature allows the driver to operate the 

ignition switch with the push of a button as long as 

the key fob is in the passenger compartment.

NOTE:

The key fob’s wireless signal may be blocked if 

the key fob is located next to a mobile phone, 

laptop, or other electronic device. This may 

result in poor performance.

The key fob allows you to lock or unlock the 

doors and liftgate from distances up to approxi

-

mately 66 ft (20 m). The key fob does not need 

to be pointed at the vehicle to activate the 

system.

1 — PANIC Button
2 — Unlock Button
3 — Lock Button
4 — Remote Start Button
5 — Emergency Key Location

GETTING TO KNOW YOUR VEHICLE

15

Key Fob For Keyless Ignition

NOTE:

In case the ignition switch does not change with 

the push of a button, the key fob may have a low 

or fully depleted battery. A low key fob battery 

can be verified by referring to the instrument 

cluster, which will display directions to follow.

Improper disposal of key fob batteries may be 

harmful to the environment. Please see an 

authorized dealer for proper battery disposal  

Ú

page 308.

To Lock/Unlock The Doors And Liftgate

Push the interior door unlock button on the door 

panel.

NOTE:

If the vehicle is unlocked using the interior door 

panel, and no door is opened within 60 seconds, 

the vehicle will relock and if equipped, the security 

system will arm. You can change the current 

setting within the Uconnect system  

Ú

page 150.

Push and release the unlock button on the key fob 

once to unlock the driver’s door, or twice within five 

seconds to unlock all the doors and the liftgate. To 

lock all the doors and the liftgate, push the lock 

button once.
When the doors unlock, the turn signals will flash 

and Illuminated Approach will be activated. When 

the doors lock, the turn signals will flash and the 

horn will chirp. This setting can be adjusted in the 

Uconnect system  

Ú

page 150.

Key Left Vehicle Feature

If a valid key fob is no longer detected inside the 

vehicle while the vehicle’s ignition system is in the 

ON/RUN or START position, the message “Key Left 

Vehicle” will be shown in the instrument cluster 

display along with an interior chime. An exterior 

audible and visual alert will also be activated to 

warn the driver.
The vehicle’s horn will rapidly chirp three times 

along with a single flash of the vehicle’s exterior 

lights.

NOTE:

The doors have to be open and then closed in 

order for the vehicle to check for the presence of 

a key fob; the Key Left Vehicle feature will not 

activate until all of the doors are closed.

These alerts will not be activated in situations 

where the vehicle’s engine is left running with 

the key fob inside.

Replacing The Battery In The Key Fob

The replacement battery is one CR2032 battery.

NOTE:

Customers are recommended to use a battery 

obtained from Mopar®. Aftermarket coin 

battery dimensions may not meet the original 

OEM coin battery dimensions.

Perchlorate Material — special handling may 

apply. See www.dtsc.ca.gov/hazardouswaste/

perchlorate for further information.

Do not touch the battery terminals that are on 

the back housing or the printed circuit board.

1 — Unlock Button
2 — Liftgate Button (If Equipped)
3 — Lock Button
4 — Remote Start Button (If Equipped)
5 — PANIC Button
6 — Emergency Key

2

16

GETTING TO KNOW YOUR VEHICLE

 

(Continued)

1. Remove the emergency key by sliding the 

mechanical latch on the back of the key fob 

sideways with your thumb and then pulling 

the key out with your other hand.

Emergency Key Removal

Emergency Key Removal

2. Separating key fob halves requires screw 

removal (if equipped), and gently prying the 

two halves of the key fob apart. Make sure not 

to damage the seal during removal.

3. Remove the battery by turning the back cover 

over (battery facing downward) and tapping it 

lightly on a solid surface such as a table or 

similar, then replace the battery. When 

replacing the battery, match the (+) sign on the 

battery to the (+) sign on the inside of the 

battery clip, located on the back cover. Avoid 

touching the new battery with your fingers. 

Skin oils may cause battery deterioration. If 

you touch a battery, clean it with rubbing 

alcohol.

4. To assemble the key fob case, snap the two 

halves together, reposition and secure the 

screw.

Programming And Requesting Additional 

Key Fobs   

Programming the key fob may be performed by an 

authorized dealer.

NOTE:

Once a key fob is programmed to a vehicle, it 

cannot be repurposed and reprogrammed to 

another vehicle.

Only key fobs that are programmed to the 

vehicle electronics can be used to start and 

operate the vehicle. Once a key fob is 

programmed to a vehicle, it cannot be 

programmed to any other vehicle.

WARNING!

The integrated key fob contains a coin cell 

battery. Do not ingest the battery; there is a 

chemical burn hazard. If the coin cell battery is 

swallowed, it can cause severe internal burns 

in just two hours and can lead to death.

If you think a battery may have been swal

-

lowed or placed inside any part of the body, 

seek immediate medical attention.

Keep new and used batteries away from chil

-

dren. If the battery compartment does not 

close securely, stop using the product and 

keep it away from children.

WARNING!

Always remove the key fobs from the vehicle 

and lock all doors when leaving the vehicle 

unattended.

For vehicles equipped with Keyless 

Enter ‘n Go™ Ignition, always remember to 

place the ignition in the OFF position.

WARNING!

GETTING TO KNOW YOUR VEHICLE

17

Duplication of key fobs may be performed at an 

authorized dealer. This procedure consists of 

programming a blank key fob to the vehicle 

electronics. A blank key fob is one that has never 

been programmed.

NOTE:

When having the Sentry Key Immobilizer system 

serviced, bring all vehicle keys with you to an 

authorized dealer.

Keys must be ordered to the correct key cut to 

match the vehicle locks.

SENTRY KEY

The Sentry Key Immobilizer system prevents 

unauthorized vehicle operation by disabling the 

engine. The system does not need to be armed or 

activated. Operation is automatic, regardless of 

whether the vehicle is locked or unlocked.
The system uses a key fob, keyless push button 

ignition and a Radio Frequency (RF) receiver to 

prevent unauthorized vehicle operation. Therefore, 

only key fobs that are programmed to the vehicle 

can be used to start and operate the vehicle. The 

system cannot reprogram a key fob obtained from 

another vehicle.
After placing the ignition in the ON/RUN position, 

the Vehicle Security Light will turn on for three 

seconds for a bulb check. If the light remains on 

after the bulb check, it indicates that there is a 

problem with the electronics. In addition, if the light 

begins to flash after the bulb check, it indicates 

that someone attempted to start the engine with 

an invalid key fob. In the event that a valid key fob 

is used to start the engine but there is an issue 

with the vehicle electronics, the engine will start 

and shut off after two seconds.
If the Vehicle Security Light turns on during normal 

vehicle operation (vehicle running for longer than 

10 seconds), it indicates that there is a fault in the 

electronics. Should this occur, have the vehicle 

serviced as soon as possible by an authorized 

dealer.

All of the key fobs provided with your new vehicle 

have been programmed to the vehicle electronics  

Ú

page 308.

IGNITION SWITCH  

I

GNITION

 N

ODE

 M

ODULE

 (IGNM) — 

I

F

 E

QUIPPED

The Ignition Node Module (IGNM) operates similar 

to an ignition switch. It has four operating 

positions, three with detents and one that is 

spring-loaded. The detent positions are OFF, ACC, 

and ON/RUN. The START position is a 

spring-loaded momentary contact position. When 

released from the START position, the switch 

automatically returns to the ON/RUN position.

Ignition Switch

CAUTION!

The Sentry Key Immobilizer system is not 

compatible with some aftermarket Remote Start 

systems. Use of these systems may result in 

vehicle starting problems and loss of security 

protection.

1 — OFF
2 — ACC (Accessory)
3 — ON/RUN
4 — START

2

18

GETTING TO KNOW YOUR VEHICLE

 

(Continued)

K

EYLESS

 E

NTER

 ‘

N

 G

O

™ I

GNITION

(I

F

 E

QUIPPED

)

This feature allows the driver to operate the 

ignition switch with the push of a button as long as 

the key fob is in the passenger compartment.
The START/STOP ignition button has several 

operating modes that are labeled and will 

illuminate when in position. These modes are OFF, 

ACC, ON/RUN, and START.

Push Button Ignition

The push button ignition can be placed in the 

following modes:
OFF

The engine is stopped

Some electrical devices (e.g. power locks, 

alarm, etc.) are still available

ACC

Engine is not started

Some electrical devices are available (e.g. 

power sunroof, power windows, etc.)

ON/RUN

Driving position

All electrical devices are available (e.g. climate 

controls, heated seats, etc.)

START

The engine will start (when foot is on the brake)

NOTE:

If the ignition switch does not change with the push 

of a button, the key fob may have a low battery. In 

this situation, a backup method can be used to 

operate the ignition switch. Put the nose side (side 

opposite of the emergency key) of the key fob 

against the START/STOP ignition button and push 

to operate the ignition switch.

Starting The Ignition With Depleted Key Fob Battery

1 — OFF
2 — ACC
3 — ON/RUN

WARNING!

Before exiting a vehicle, always come to a 

complete stop, then shift the automatic trans

-

mission into PARK, apply the parking brake, 

place the engine in the OFF position, remove 

the key fob from the vehicle and lock your 

vehicle. If equipped with Keyless Enter ‘n Go™, 

always make sure the keyless ignition is in OFF 

position, remove the key fob from the vehicle 

and lock the vehicle.

Never leave children alone in a vehicle, or with 

access to an unlocked vehicle.

GETTING TO KNOW YOUR VEHICLE

19

NOTE:

For information on normal starting, see  

Ú

page 90.

When opening the driver's door and the ignition 

is in the ON/RUN (engine not running) position, 

a chime will sound to remind you to place the 

ignition in the OFF position. In addition to the 

chime, the message “Ignition or Accessory ON” 

will display in the cluster.

The power window switches and power sunroof 

(if equipped) will remain active for three 

minutes after the ignition is placed in the OFF 

position. Opening either front door will cancel 

this feature. The timing for this feature is 

programmable.

REMOTE START — IF EQUIPPED  

This system uses the key fob to start the 

engine conveniently from outside the 

vehicle while still maintaining security. 

The system has a range of approximately 

328 ft (100 m).

Remote Start is used to defrost windows in cold 

weather, and to reach a comfortable climate in all 

ambient conditions before the driver enters the 

vehicle.

NOTE:

Obstructions between the vehicle and key fob may 

reduce this range  

Ú

page 308.

H

OW

 T

O

 U

SE

 R

EMOTE

 S

TART

Push and release the Remote Start button on the 

key fob twice within five seconds. The vehicle 

doors will lock, the parking lights will flash, and the 

horn will chirp twice (if programmed). Then, the 

engine will start, and the vehicle will remain in the 

Remote Start mode for a 15 minute cycle. Pushing 

the Remote Start button a third time shuts the 

engine off.

Allowing children to be in a vehicle unattended 

is dangerous for a number of reasons. A child 

or others could be seriously or fatally injured. 

Children should be warned not to touch the 

parking brake, brake pedal or the gear 

selector.

Do not leave the key fob in or near the vehicle, 

or in a location accessible to children, and do 

not leave the ignition of a vehicle equipped 

with Keyless Enter ‘n Go™ in the ON/RUN 

position. A child could operate power 

windows, other controls, or move the vehicle.

Do not leave children or animals inside parked 

vehicles in hot weather. Interior heat buildup 

may cause serious injury or death.

CAUTION!

An unlocked vehicle is an invitation for thieves. 

Always remove key fob from the vehicle and lock 

all doors when leaving the vehicle unattended.

WARNING!

WARNING!

Do not start or run an engine in a closed 

garage or confined area. Exhaust gas contains 

Carbon Monoxide (CO) which is odorless and 

colorless. Carbon Monoxide is poisonous and 

can cause serious injury or death when 

inhaled.

Keep key fobs away from children. Operation 

of the Remote Start system, windows, door 

locks or other controls could cause serious 

injury or death.

2

20

GETTING TO KNOW YOUR VEHICLE

 

NOTE:

With Remote Start, the engine will only run for 

15 minutes.

Remote Start can only be used twice.

The ignition must be placed in the ON/RUN posi

-

tion before the Remote Start sequence can be 

repeated for a third cycle.

If an engine fault is present or fuel level is low, 

the vehicle will start and then shut down in 

10 seconds.

The parking lights will turn on and remain on 

during Remote Start mode.

For security, power window and power sunroof 

operation (if equipped) are disabled when the 

vehicle is in the Remote Start mode.

The ignition must be placed in the ON/RUN posi

-

tion before the Remote Start sequence can be 

repeated for a third cycle.

All of the following conditions must be met before 

the engine will remote start:

Gear selector in PARK

Doors closed

Hood closed

Liftgate closed

Hazard switch off

Brake switch inactive (brake pedal not pressed)

Battery at an acceptable charge level

System not disabled from previous Remote 

Start event

Vehicle Security system indicator flashing

Ignition in OFF position

Fuel level meets minimum requirement

Vehicle Security system is not signaling an intru

-

sion

Malfunction Indicator Light (MIL) is not illumi

-

nated

T

O

 E

XIT

 R

EMOTE

 S

TART

 M

ODE

To drive the vehicle after starting the Remote Start 

system, push and release the START/STOP ignition 

button while pressing the brake pedal prior to the 

end of the 15 minute cycle. If the vehicle is not 

equipped with a START/STOP ignition button, 

insert the key fob into the ignition switch and place 

the ignition in the ON/RUN position.
The Remote Start system will turn the engine off if 

the Remote Start button on the key fob is pushed 

again, or if the engine is allowed to run for the 

entire 15 minute cycle. Once the driver’s door is 

opened, or the ignition is placed in the ON/RUN 

position, the climate controls will resume 

previously set operations (temperature, blower 

control, etc.).

NOTE:

For vehicles equipped with the Keyless 

Enter ‘n Go™ — Passive Entry feature, the 

message “Remote Start Active — Push Start 

Button” will show in the instrument cluster 

display until you push the START/STOP ignition 

button.

To avoid unintentional shutdowns, the system 

will disable for two seconds after receiving a 

valid Remote Start request.

WARNING!

Do not start or run an engine in a closed 

garage or confined area. Exhaust gas contains 

Carbon Monoxide (CO) which is odorless and 

colorless. Carbon Monoxide is poisonous and 

can cause serious injury or death when 

inhaled.

Keep key fobs away from children. Operation 

of the Remote Start system, windows, door 

locks or other controls could cause serious 

injury or death.

GETTING TO KNOW YOUR VEHICLE

21

R

EMOTE

 S

TART

 F

RONT

 D

EFROST

 

A

CTIVATION

 — I

F

 E

QUIPPED

When Remote Start is active, and the outside 

ambient temperature is 40°F (4.5°C) or below, the 

system will automatically activate front defrost for 

15 minutes or less. The time is dependent on the 

ambient temperature. Once the timer expires, the 

system will automatically adjust the settings 

depending on ambient conditions. See “Remote 

Start Comfort Systems — If Equipped” in the next 

section for detailed operation.

R

EMOTE

 S

TART

 C

OMFORT

 S

YSTEMS

 — 

I

F

 E

QUIPPED

 

When Remote Start is activated, the front and rear 

defrost will automatically turn on in cold weather. 

The heated steering wheel and driver heated seat 

feature will turn on if selected in the comfort menu 

screen within Uconnect Settings  

Ú

page 150. In 

warm weather, the driver vented seat feature will 

automatically turn on when the Remote Start is 

activated, if programmed in the comfort menu 

screen. The vehicle will adjust the climate control 

settings depending on the outside ambient 

temperature.

Automatic Temperature Control (ATC) — 

If Equipped
The climate controls automatically adjust to the 

optimal temperature and mode settings 

dependent on the outside ambient temperature. 

This will occur until the driver’s door is opened, or 

the ignition is placed in the ON/RUN position, 

where the climate controls will resume their 

previous settings.
Manual Temperature Control (MTC) — If Equipped

In ambient temperatures at 40°F (4.5°C) or 

below, the climate settings will default to 

maximum heat, with fresh air entering the 

cabin. If the front defrost timer expires, the 

vehicle will enter Mix Mode.

In ambient temperatures from 40°F (4.5°C) to 

78°F (26°C), the climate settings will be based 

on the last settings selected by the driver.

In ambient temperatures at 78°F (26°C) or 

above, the climate settings will default to MAX 

A/C, Bi-Level Mode, and Recirculation on.

For more information on ATC, MTC, and climate 

control settings, see  

Ú

page 51.

NOTE:

These features will stay on through the duration of 

Remote Start until the driver’s door is opened, or 

until the ignition is placed in the ON/RUN position. 

The climate control settings will change if manually 

adjusted by the driver while the vehicle is in 

Remote Start mode, and exit automatic override. 

This includes the OFF button on the climate 

controls, which will turn the system off.

R

EMOTE

 S

TART

 W

INDSHIELD

 W

IPER

 

D

E

–I

CER

 A

CTIVATION

 — I

F

 E

QUIPPED

When Remote Start is active and the outside 

ambient temperature is less than 33°F (0.6°C), 

the Windshield Wiper De-Icer will activate. Exiting 

Remote Start will resume its previous operation. If 

the Windshield Wiper De-Icer was active, the timer 

and operation will continue.

R

EMOTE

 S

TART

 C

ANCEL

 M

ESSAGE

The following messages will display in the 

instrument cluster display if the vehicle fails to 

remote start, or exits Remote Start prematurely:

Remote Start Cancelled — Door Open

Remote Start Cancelled — Hood Open

Remote Start Cancelled — Fuel Low

Remote Start Cancelled — Liftgate Open

Remote Start Disabled — Start Vehicle To Reset

Remote Start Cancelled — Too Cold

Remote Start Cancelled — Time Expired

The message will stay active until the ignition is 

placed in the ON/RUN position.

2

22

GETTING TO KNOW YOUR VEHICLE

 

VEHICLE SECURITY SYSTEM — IF EQUIPPED  

The Vehicle Security system monitors the vehicle 

doors, hood, liftgate, and the Keyless Enter ‘n Go™ 

Ignition for unauthorized operation. While the 

Vehicle Security system is armed, interior switches 

for door locks and liftgate release are disabled. If 

something triggers the alarm, the Vehicle Security 

system will provide the following audible and 

visible signals:

The horn will pulse.

The turn signals will flash.

The Vehicle Security Light in the instrument 

cluster will flash.

T

O

 A

RM

 T

HE

 S

YSTEM

 

Follow these steps to arm the Vehicle Security 

system:
1. Make sure the vehicle’s ignition is placed in 

the OFF position.

For vehicles equipped with Keyless Entry, 

make sure the vehicle’s keyless ignition 

system is OFF.

2. Perform one of the following methods to lock 

the vehicle:

Push the lock button on the interior power 

door lock switch with the driver and/or 

passenger door open.

Push the lock button on the exterior Passive 

Entry door handle with a valid key fob avail

-

able in the same exterior zone  

Ú

page 24.

Push the lock button on the key fob.

3. If any doors are open, close them.

T

O

 D

ISARM

 T

HE

 S

YSTEM

 

The Vehicle Security system can be disarmed using 

any of the following methods:

Push the unlock button on the key fob.

Grab the Passive Entry door handle to unlock 

the door  

Ú

page 24.

Cycle the ignition out of the OFF position to 

disarm the system.

NOTE:

The driver's door key cylinder and the liftgate 

button on the key fob cannot arm or disarm the 

Vehicle Security system.

The Vehicle Security system remains armed 

during power liftgate entry. Pushing the liftgate 

button will not disarm the Vehicle Security 

system. If someone enters the vehicle through 

the liftgate and opens any door, the alarm will 

sound.

When the Vehicle Security system is armed, the 

interior power door lock switches will not unlock 

the doors.

The Vehicle Security system is designed to protect 

your vehicle. However, you can create conditions 

where the system will give you a false alarm. If one 

of the previously described arming sequences has 

occurred, the Vehicle Security system will arm, 

regardless of whether you are in the vehicle or not. 

If you remain in the vehicle and open a door, the 

alarm will sound. If this occurs, disarm the Vehicle 

Security system.
If the Vehicle Security system is armed and the 

battery becomes disconnected, the Vehicle 

Security system will remain armed when the 

battery is reconnected; the exterior lights will flash, 

and the horn will sound. If this occurs, disarm the 

Vehicle Security system.

R

EARMING

 O

F

 T

HE

 S

YSTEM

If something triggers the alarm and no action is 

taken to disarm it, the Vehicle Security system will 

turn the horn off after a 29 second cycle (with five 

seconds between cycles and up to eight cycles if 

the trigger remains active) and then rearm itself.

S

ECURITY

 S

YSTEM

 M

ANUAL

 O

VERRIDE

The Vehicle Security system will not arm if you lock 

the doors using the manual door lock.

GETTING TO KNOW YOUR VEHICLE

23

DOORS 

M

ANUAL

 D

OOR

 L

OCKS

To lock each door, rotate the door lock knob on 

each door trim panel until the red area is hidden. 

To unlock the front doors, pull the inside door 

handle to the first detent or rotate the door lock 

button until the red indicator is visible. To unlock 

the rear doors, rotate the door lock button until the 

red indicator is visible.
If the red indicator is hidden when you shut the 

door, the door is locked. Therefore, make sure the 

key fob is not inside the vehicle before closing the 

door.

NOTE:

The manual door locks will not lock or unlock the 

liftgate.

Lock Knob And Door Handle

P

OWER

 D

OOR

 L

OCKS

 

The power door lock switches are located on each 

front door panel. Push the switch to lock or unlock 

the doors.

NOTE:

The key fob may not be detected by the vehicle 

Keyless Enter ‘n Go™ system if it is located next to 

a mobile phone, laptop or other electronic device; 

these devices may block the key fob’s wireless 

signal and prevent the Keyless Enter ‘n Go™ 

system from starting the vehicle.

Power Door Lock Switches

The driver’s door will unlock automatically if the 

keys are detected inside the vehicle when door 

lock button on the front door panel is used to lock 

the door. This will occur for two attempts. Upon the 

third attempt, the doors will lock even if the key fob 

is inside.

WARNING!

For personal security and safety in the event 

of a collision, lock the vehicle doors before you 

drive as well as when you park and exit the 

vehicle.

When exiting the vehicle, always remove the 

key fob from the vehicle and lock your vehicle. 

If equipped with Keyless Enter ‘n Go™ Ignition, 

always make sure the keyless ignition is 

placed in the OFF position, and remove the 

key fob from the vehicle and lock the vehicle. 

Unsupervised use of vehicle equipment may 

cause severe personal injuries or death.

Never leave children alone in a vehicle, or with 

access to an unlocked vehicle. Allowing chil

-

dren to be in a vehicle unattended is 

dangerous for a number of reasons. A child or 

others could be seriously or fatally injured. 

Children should be warned not to touch the 

parking brake, brake pedal or the gear 

selector.

Do not leave the key fob in or near the vehicle, 

or in a location accessible to children, and do 

not leave the ignition of a vehicle equipped 

with Keyless Enter ‘n Go™ Ignition in the ACC 

or ON/RUN position. A child could operate 

power windows, other controls, or move the 

vehicle.

2

24

GETTING TO KNOW YOUR VEHICLE

 

If the door lock switch is pushed while the ignition 

is in the ACC or ON/RUN position and the driver's 

door is open, the doors will not lock.
If a rear door is locked, it cannot be opened from 

inside the vehicle without first unlocking the door. 

The door may be unlocked manually by rotating the 

lock knob.

K

EYLESS

 E

NTER

 ‘

N

 G

O

™ — 

P

ASSIVE

 E

NTRY

 

The Passive Entry system is an enhancement to 

the vehicle’s Remote Keyless Entry system and a 

feature of Keyless Enter ‘n Go™ — Passive Entry. 

This feature allows you to lock and unlock the 

vehicle’s door(s) and fuel door without having to 

push the key fob lock or unlock buttons.

NOTE:

Passive Entry may be programmed on/off within 

the Uconnect system  

Ú

page 150.

If wearing gloves, or if it has been raining/

snowing on the Passive Entry door handle, the 

unlock sensitivity can be affected, resulting in a 

slower response time.

If the vehicle is unlocked by Passive Entry and 

no door is opened within 60 seconds, the 

vehicle will relock and if equipped will arm the 

Vehicle Security system.

The key fob may not be detected by the vehicle 

Passive Entry system if it is located next to a 

mobile phone, laptop or other electronic device; 

these devices may block the key fob's wireless 

signal and prevent the Passive Entry handle 

from locking/unlocking the vehicle.

Passive Entry activates illuminated approach for 

the time set by the customer within the 

Uconnect system (0, 30, 60, or 90 seconds), 

and flashes the turn signal lights.

To Unlock From The Driver Or Passenger Side
With a valid Passive Entry key fob within 5 ft 

(1.5 m) of the door handle, grab the handle to 

unlock the vehicle. Grabbing the driver’s door 

handle will unlock the driver door automatically. 

Grabbing the passenger door handle will unlock all 

doors and the liftgate automatically.

Grab The Door Handle To Unlock

NOTE:

Either the driver door only or all doors will unlock 

when you grab hold of the front driver’s door 

handle, depending on the selected setting in the 

Uconnect system  

Ú

page 150.

All doors will unlock when the front passenger 

door handle is grabbed regardless of the 

driver’s door unlock preference setting.

Frequency Operated Button Integrated Key 

(FOBIK-Safe)
To minimize the possibility of unintentionally 

locking a Passive Entry key fob inside your vehicle, 

the Passive Entry system is equipped with an 

automatic door unlock feature which will function if 

the ignition is OFF.
There are three situations that trigger a 

FOBIK-Safe search in any Passive Entry vehicle:

A lock request is made by a valid Passive Entry 

key fob while a door is open.

A lock request is made by the Passive Entry door 

handle while a door is open.

A lock request is made by the door panel switch 

while the door is open.

When any of these situations occur, after all open 

doors are shut, the FOBIK-Safe search will be 

executed. If it detects a Passive Entry key fob 

inside the car, the car will unlock and alert the 

customer.

 

 

 

 

 

 

 

 

Content      ..      1       2         ..

 

 

///////////////////////////////////////