Jaguar XJ (2008 year). Manual - part 73

293

Radio

R

Auto Memory (A MEM)

The automatic memory function 
programmes the nine strongest 
stations on a selected waveband 
to presets 1 to 9.

Note: These are additional to the preset 
stations described earlier.

To activate this function, press and hold 
A MEM button for at least two seconds.

The radio will be briefly muted while it 
searches the waveband for the nine 
strongest stations. When programming is 
complete the radio will default to preset 
number 1 and audio volume is restored.

If stations cannot be located for all preset 
positions, those that are found will be 
allocated positions commencing with 
number 1, leaving the remainder not 
programmed. The display will show 
NO FM or NO AM if a selected preset are 
is not programmed.

To switch between the A MEM preset 
stations and your own presets, press and 
immediately release the A MEM button.

A MEM with Radio Broadcast Data 
System (RBDS) selected

If the A MEM function is operated while in 
RBDS mode, the radio will be muted 
briefly, while a search is made for the nine 
strongest RBDS stations.

Radio Set Up

This function enables the radio to be set 
to user operating preferences. By 
selecting SET UP and using the preset 
buttons, the owner or Jaguar Dealer can 
adjust certain radio functions.

When in SET UP, pressing the relevant 
preset button, as detailed below, will 
display the facility selected and its state. 
The state of that facility can be changed 
by pressing the preset button again.

To enter SET UP: Press CD Eject and 
BAND buttons simultaneously.

The display will show SET UP. The 
following preferences can be selected or 
changed in any order, within a 15 second 
period. After 15 seconds the display will 
clear and exit SET UP.

Preset 1

Press Preset 1 to enable 
or disable RBDS 
availability in the user’s 
country.

Preset 2

Blank

Preset 3

Blank.

Preset 4

Blank.

Preset 5

Blank

Preset 6

FM volume high 
(compensate for poor 
signal strength).

Note: This feature is not 
available in 
North America, Australia 
and Japan.

Preset 7

Blank.

Preset 8

Blank.

Preset 9

Blank.

Radio

294

L

Preset 10

During initial factory 
installation, this is used 
to set the radio to one of 
the following regions: 
Europe, USA, Australia 
or Japan. Regional 
settings determine the 
correct frequency 
increments required for 
seeking stations, 
automatic tuning etc.

Note: The regions are 
preset at the factory. 
Should you require a 
regional change, consult 
your Jaguar Dealer.

295

Radio

R

RADIO WITH TOUCH-SCREEN

On/Off control

Press the control knob to 
switch the radio on, press 
again to switch off.

Pressing the AUDIO button 
can also turn on the radio. 
When using the 
touch-screen in other 
operating modes, such as 
Navigation, Television 

(where fitted), Climate Control or any of 
the setup screens, pressing the AUDIO 
button will revert to the relevant audio 
screen.

Volume control

Turn the control knob clockwise to 
increase or counter-clockwise to 
decrease volume, across a range of 
settings (0 – 35) to be displayed during 
and momentarily after adjustment.

When using the rotary control knob to 
adjust volume the touch-screen will show 
the above display to assist setting. The 
pop-up volume control slide will 
disappear from the display after 
five seconds or can be removed by 
touching it.

Any volume setting made whilst in audio, 
telephone or navigation mode or 
JaguarVoice, will be memorised for that 
system.
Automatic Volume Control

This maintains radio volume at a level 
sufficient to overcome road noise as 
vehicle speed increases or decreases. To 
activate AVC, press the MENU button, 
followed by the VOLUME PRESET 
button on the touch-screen. Once in the 
volume preset screen, AVC level can be 
adjusted (from OFF to 5) by repeatedly 
pressing the + or – buttons adjacent to 
the AVC volume indicator.

When AVC is ON, manual adjustment of 
volume will override the AVC setting.

Volume preset adjustments

Volume for Telephone, JaguarVoice, TA 
and Navigation can also be adjusted by 
using the MENU button on the right of the 
screen and selecting the volume preset 
button as appropriate.

Radio

296

L

Audio setup

This function enables the radio to be set 
to user operating preferences. By 
selecting SETUP and using the buttons 
on the touch-screen, the owner or Jaguar 
Dealer can adjust certain radio functions.

When in SETUP, pressing the relevant 
button will display the facility selected 
and its state. The state of that facility can 
be changed by pressing the button again.

To enter SETUP: Press Eject and BAND 
buttons simultaneously.

The display will show AUDIO SETUP. The 
preferences shown on the next page can 
then be selected or changed in any order. 
After 15 seconds the display will clear and 
exit SETUP.

Market

During initial factory 
installation, this is used 
to set the radio to one of 
the following regions: 
Europe, Australia or 
Japan. Regional settings 
determine the correct 
frequency increments 
required for seeking 
stations, automatic 
tuning etc.

Note: The regions are 
preset at the factory. 
Should you require a 
regional change, consult 
your Jaguar Dealer.

RBDS/
RBDS

Press ON/OFF buttons 
to enable or disable 
RBDS, depending upon 
RBDS availability in the 
user’s country.

FM Volume

FM volume high or low 
(compensate for poor 
signal strength).

Note: This feature is not 
available in Australia and 
Japan.