Isuzu KB P190. Manual - part 931

 

  Index      Isuzu     Isuzu KB P190 - service repair manual 2007 year

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  929  930  931  932   ..

 

 

Isuzu KB P190. Manual - part 931

 

 

Powertrain Interface Module – V6 

Page 6E1–63 

 

PRND32L Display Diagnostic Table 

Step Action 

Yes 

No 

1 

Has the Diagnostic System Check been performed? 

 

Go to Step 2 

Refer to 

Diagnostic 

System Check 

in this section

2 

1 

Turn the ignition to the ON position. 

2 

Move the gear select lever through each gear position and 
check the instrument cluster PRND32L display. 

Does each indicator display an off to on condition? 

Refer to Additional 

Information in this 

section 

Go to Step 3 

3 

Are any of the indicators permanently illuminated? 

Go to Step 5 

Go to Step 4 

4 

1 

Using Tech 2 select, 
 
Body / PIM / Miscellaneous Tests / Status Indicators / 
PRNDL Lamps. 

2 

Using the Tech 2 soft keys step through the sequence of 
illuminating each PRND32L indicator in turn. 

Does each indicator display an off to on condition? 

Go to Step 8 

Go to Step 10 

5 

Disconnect the TCM harness connector. Refer to 7C4 Automatic 
Transmission – 4L60E – On-vehicle Servicing. 

Is the indicator in Step 3 still permanently illuminated? 

Go to Step 6 

Go to Step 8 

6 

Disconnect the PIM harness connector. Refer to 11.2 Powertrain 
Interface Module in this Section. 

Is the indicator in Step 3 still permanently illuminated? 

Go to Step 7 

Go to Step 14 

7 

Turn the ignition to the ON position, test for a short to voltage of the 
relevant circuits from the PIM to the instrument cluster. Refer to 6
 

Wiring Diagram and Connector Chart. 

Was any fault found and rectified? 

Go to step 15 

Go to step 12 

8 

Check the neutral start and back-up lamp switch and automatic 
transmission for correct operation. Refer to 7C2 Automatic 
Transmission – 4L60E – Electrical Diagnosis. 

Was any fault found and rectified? 

Go to Step 15 

Go to 9 

9 

Replace the TCM. Refer to 7C4 Automatic Transmission – 4L60E – 
On-vehicle Servicing. 

Has the repair been completed? 

Go to Step 15 

— 

10  1 

Disconnect the instrument cluster harness connector. 

2 

Turn the ignition to the ON position. 

3 

While sequencing each PRND32L indicator, back probe the 
relevant connector pins at the rear of the instrument cluster. 
Refer to 6  Wiring Diagram and Connector Chart. 

Does the multimeter display a change from 0 to 10 Volts as each 
PRND32L indicator position is selected? 

Go to Step 12 

Go to 11 

11  Test for high resistance, open circuit, a short to ground of the relevant 

circuits from the PIM to the instrument cluster. Refer to 6 

Wiring 

Diagram and Connector Chart. 

Was any fault found and rectified? 

Go to Step 15 

Go to Step 14 

Powertrain Interface Module – V6 

Page 6E1–64 

 

Step Action 

Yes 

No 

12  Test the following instrument cluster circuits for a high resistance, 

open circuit or short to ground fault condition: 

• 

all 12 V battery supply circuits 

• 

all instrument cluster ground connections 

Was any fault found and rectified? 

Go to Step 15 

Go to Step 13 

13  Replace the instrument cluster. 

Has the repair been completed? 

Go to Step 15 

— 

14  Replace the PIM. 

Has the repair been completed? 

Go to step 15 

— 

15  1 

Turn the ignition to the ON position. 

2 

Move the gear select lever through each gear position and 
check the PRND32L display. 

Does each indicator display an off to on condition? 

System OK 

Go to step 2 

When all diagnosis and repairs are completed, clear all DTCs and check the system for correct operation. 

10.2 Warning Signal and Status Indicators 

Diagnostics 

Circuit Description 

The powertrain interface module (PIM) is connected to the instrument cluster by a series of hard wired connections to 
illuminate the appropriate warnings and indicators within the instrument cluster. Some of these components do not set a 
DTC, in the event of a component failure. The following diagnostic procedures are devised to assist in these cases. 

Additional Information 

• 

Refer to 7.2 Diagnostic System Check to monitor DTC’s. 

• 

Refer to 8A Electrical Body and Chassis for the following information: 

• 

Automatic transmission PRND32L switch and wiring, 

• 

TCM wiring diagram. 

• 

Refer to 6  Wiring Diagram and Connector Chart for the following information: 

• 

PIM connector illustration and terminal assignment, and 

• 

PIM wiring diagram. 

• 

For intermittent faults, refer to Intermittent Fault Conditions. 

• 

Check for an intermittent fault in the wiring harness or connectors, if a fault cannot be found the system is 
serviceable. 

Test Description 

The following numbers refer to the step numbers in the diagnostic table: 

1 

This step tests for DTC’s in the overall system. 

2 

This step manually tests the warning indicators. 

5 

This step uses Tech 2 to drive each status indicator on. 

6 

This step uses Tech 2 to drive each warning indicator on. 

9 

This step tests the wiring harness between the PIM and the Instrument Cluster. 

Powertrain Interface Module – V6 

Page 6E1–65 

 

Hard-wired Warning Signals  

Display Indicator 

CHECK TRANS 

Lamp 

3

rd

 START 

Lamp 

POWER Lamp 

A/T OIL TEMP 

Lamp 

CRUISE SET 

Lamp 

OIL Lamp 

THERMO Gauge 

SVS Lamp 

CHARGE Lamp 

TACHO Gauge 

Warning Signal and Status Indicator Diagnostic Table 

Step Action 

Yes 

No 

1 

Has the Diagnostic System Check been performed? 

Go to Step 2 

Refer to 

Additional 

Information 

2 

Turn the Ignition to the ON position, observe if all warning and status 
indicators illuminate during the Instrument Cluster start up sequence.

Do all indicators illuminate? 

Go to Step 3 

Go to step 4 

3 

1 

Start the vehicles engine. 

2 

Are any of the warning or status indicators permanently 
illuminated? 

Go to Step 7 

Go to Step 4 

4 

Using Tech 2. 

Are any DTC’s set which may cause incorrect operation of the warning 
or status indicators? 

Refer to the 

relevant DTC’s 

section 

Go to Step 5 

5 

1 

Using Tech 2 select, 
Body / PIM / Miscellaneous Tests / Status Indicators. 

2 

Select and activate in turn Cruise Control ON Lamp / Cruise 
Control Set Lamp / Power Drive Lamp. 

Does each indicator illuminate? 

Go to Step 6 

Go to Step 8 

6 

1 

Using Tech 2 select, 
Body / PIM / Miscellaneous Tests / Warnings. 

2 

Select and activate in turn, ALT / Oil Pressure / Service Soon / 
A/T Oil Temp / Check Trans. 

Does each warning illuminate? 

Go to Step 15 

Go to Step 8 

7 

Disconnect the PIM harness connector. Refer to 11.2 Powertrain 
Interface Module in this section. 

Is the indicator/warning in Step 3 still permanently illuminated? 

Go to Step 9 

Go to Step 12 

8 

Remove and test the lamp from the malfunctioning warning. 

Was the lamp found to be faulty and replaced? 

Go to Step 15 

Go to Step 14 

Powertrain Interface Module – V6 

Page 6E1–66 

 

Step Action 

Yes 

No 

9 

Test for high resistance, open circuit, a short to ground of the relevant 
circuits from the PIM to the instrument cluster. Refer to 6 

Wiring 

Diagram and Connector Chart. 

Was any fault found and rectified? 

Go to Step 16 

Go to step 10 

10  Turn the ignition to the ON position, test for a short to voltage of the 

relevant circuits from the PIM to the instrument cluster. Refer to 6
 

Wiring Diagram and Connector Chart. 

Was any fault found and rectified? 

Go to Step 16 

Go to Step 11 

11  Disconnect the PIM. 

Test for a short to voltage of the relevant circuits from the PIM to the 
instrument cluster. 

Was any fault found and rectified? 

Go to Step 13 

Go to Step 12 

12  Disconnect the instrument cluster. 

Test for a short to voltage of the relevant circuits from the PIM to the 
instrument cluster. 

Was any fault found and rectified? 

Go to Step 16 

Go to Step 14 

13  Replace the PIM. 

Has the repair been completed? 

Go to Step 16 

— 

14  Test the following instrument cluster circuits for a high resistance, 

open circuit or short to ground fault condition: 

• 

all 12 V battery supply circuits 

• 

all instrument cluster ground connections 

Was any fault found and rectified? 

Go to Step 16 

Go to Step 15 

15  Replace the instrument cluster. 

Has the repair been completed? 

Go to Step 16 

— 

16  Turn the Ignition to the ON position, observe if all warning indicators 

illuminate during the Instrument Cluster start up sequence. 

Do all indicators function correctly? 

System serviceable 

Go to step 3 

When all diagnosis and repairs are completed, clear all DTCs and check the system for correct operation. 

 

 

 

 

 

 

 

Content   ..  929  930  931  932   ..