Honda CR-V (2022 year). Manual in english

205

Security System

Super Locking

Co
ntrols

Super Locking

The super locking function disables the lock tabs on all doors.

■

To activate the super locking function

•

Turn the key in the driver’s door towards the vehicle front twice within five
seconds.

•

Press the lock button on the remote transmitter twice within five seconds.

•

Touch the door lock sensor on the door handle or press the lock button on the
tailgate twice within five seconds.

■

To cancel the super locking function

Unlock the driver’s door with the remote transmitter or keyless access system

Super Locking

Do not unlock the door using the key. The security
system alarm goes off.

Once the super locking function has been enabled, it
will remain enabled even if you unlock the tailgate.

WARNING

No one must be inside the vehicle with the
super locking set. Persons locked in can get
seriously sick or die from the heat built
inside the vehicle if left in the sun.

Make sure there is no one inside the vehicle
before setting the super locking.

Models with keyless access system

* Not available on all models

206

Co
ntrols

Windows

Opening/Closing the Power Windows

The power windows can be opened and closed when the ignition switch is in ON

(

, using the switches on the doors.

The driver’s side switches can be used to open and close all the windows. The power
window lock button on the driver’s side must be switched off (not pushed in,
indicator off) to open and close the windows from anywhere other than the driver’s
seat.

When the power window lock button is switched on (pushed in, indicator on), you
can only operate the driver’s window. Turn the power window lock button on if a
child is in the vehicle.

*1: Models with the keyless access system have an

ENGINE START/STOP

button instead of an

ignition switch.

Opening/Closing the Power Windows

WARNING:

Always take the ignition key with you

whenever you leave the vehicle alone or with other
occupants.

The power windows can be operated for up to 10
minutes after you turn the ignition switch to LOCK

(

Closing the driver’s door cancels this function.

WARNING

Closing a power window on someone’s
hands or fingers can cause serious injury.

Make sure your passengers are away from
the windows before closing them.

Continued

207

Windows

Opening/Closing the Power Windows

Co
ntrols

■

Manual operation

To open:

Push the switch down lightly, and

hold it until the desired position is reached.

To close:

Pull the switch up lightly, and hold it

until the desired position is reached.

■

Automatic operation

To open:

Push the switch down firmly.

To close:

Pull the switch up firmly.

The window opens or closes completely. To
stop the window at any time, push or pull the
switch briefly.

■

Opening/Closing the Windows with Auto-Open/Close

Function

Opening/Closing the Power Windows

Auto Reverse

If a power window senses resistance when closing
automatically, it will stop closing and reverse
direction.

The driver’s window auto reverse function is disabled
when you continuously pull up the switch.

The auto reverse function stops sensing when the
window is almost closed to ensure that it fully closes.

Indicator

Front Passenger’s
Window Switch

Driver’s
Window
Switch

Rear Passenger’s
Window Switch

Windows

Opening/Closing the Power Windows

208

Co
ntrols

To open:

Press the unlock button, and then

within 10 seconds, press it again and hold it.

To close:

Press the lock button, and then

within 10 seconds, press it again and hold it.

If the windows stop midway, repeat the
procedure.

■

Opening/Closing the Windows with the Remote

Opening/Closing the Windows with the Remote

If you open/close the windows with the remote, the
panoramic roof will open/close automatically along
with them.

Models with panoramic roof

Unlock
Button

Lock
Button

209

Windows

Opening/Closing the Power Windows

Co
ntrols

To close:

Lock the driver’s door with the key.

Within 10 seconds of returning the key to the
central position, turn the key in the lock
direction and hold it there.

Release the key to stop the windows at the
desired position. If you want further
adjustment, repeat the same operation.

■

Closing the Windows with the Key

Closing the Windows with the Key

If you close the windows with the key ,the panoramic
roof will close automatically along with them.

Models with panoramic roof

210

Co
ntrols

Panoramic Roof

Opening/Closing the Panoramic Roof

You can only operate the panoramic roof when the power mode is in ON. Use the
switch in the front of the ceiling to open and close the panoramic roof.

Opening/Closing the Panoramic Roof

WARNING:

Always take the ignition key with you

whenever you leave the vehicle alone or with other
occupants.

NOTICE

Opening the panoramic roof in below freezing
temperature or when it is covered with snow or ice
can damage the panoramic roof panel or motor.

The panoramic roof and sunshade can be operated
for up to 10 minutes after you set the power mode to
OFF (LOCK).
Closing the driver’s door cancels this function.

WARNING

Opening or closing the panoramic roof on
someone’s hands or fingers can cause
serious injury.

Make sure all hands and fingers are clear of
the panoramic roof before opening or
closing it.

* Not available on all models

Continued

211

Panoramic Roof

Opening/Closing the Panoramic Roof

Co
ntrols

Opening/Closing the Panoramic Roof

When resistance is detected, the auto reverse
function causes the panoramic roof to change
directions, then stop. Auto reverse stops sensing
when the panoramic roof is almost closed to ensure
that it fully closes.

You can use the remote transmitter or the key to
operate the panoramic roof.

Opening/Closing the Windows with the
Remote

P. 208

Closing the Windows with the Key

P. 209

Panoramic Roof

Opening/Closing the Panoramic Roof

212

Co
ntrols

■

Automatic operation

To open:

Pull the switch back firmly.

To close:

Push the switch forward firmly.

The panoramic roof automatically opens or
closes all the way. To stop the panoramic roof
midway, pull or push the switch briefly.

■

Manual operation

To open:

Pull the switch back lightly, and

hold it until the desired position is reached.

To close:

Push the switch forward lightly, and

hold it until the desired position is reached.

■

Tilting the panoramic roof up

To tilt:

Push on the centre of the panoramic

roof switch.

The sunshades will open automatically
and the panoramic roof will start to tilt
up.

To close:

Push the switch forward firmly,

then release.

■

Using the Panoramic Roof Switch

Using the Panoramic Roof Switch

The panoramic roof cannot be fully opened in a
single operation. The panoramic roof has a
“comfort” position or wind noise reduction position
at which the roof first stops. To open fully, pull the
switch back again after the roof has stopped at this
position.

Whenever the panoramic roof is opening, the
sunshade moves along with it. However, when the
panoramic roof is closing, the sunshade does not
move.

When you tilt open the panoramic roof, the sunshade
opens slightly to let in fresh air. When you close the
panoramic roof from this position, the sunshade
returns to its closed position.

Full Open Position

Comfort Position

Open

Tilt

213

Panoramic Roof

Opening/Closing the Panoramic Roof

Co
ntrols

■

Automatic operation

To open:

Pull the switch back firmly.

To close:

Push the switch forward firmly.

The sunshade automatically opens or closes all
the way. To stop the sunshade midway, push
the switch briefly.

■

Manual operation

To open:

Pull the switch back lightly, and

hold it until the desired position is reached.

To close:

Push the switch forward lightly, and

hold it until the desired position is reached.

■

Using the Sunshade Switch

Using the Sunshade Switch

The sunshade can be opened or closed to adjust the
amount of light that enters the cabin.

When you use the sunshade switch to open the
sunshade, the panoramic roof does not move.

The sunshade cannot be fully closed if the panoramic
roof is open. When you close the sunshade with the
panoramic roof open, the sunshade stops close to the
panoramic roof glass. When you push the switch
forward again, the sunshade and the panoramic roof
close together.

Open

214

Co
ntrols

Operating the Switches Around the Steering Wheel

Ignition Switch

Models without keyless access system

Ignition Switch

You cannot take the key out unless the shift lever is
in

(

If you open the driver’s door when the key is in LOCK

(

or ACCESSORY

(

, the following messages

appear on the driver information interface:

•

In LOCK

(

or the symbol with a

Ignition

Key

•

In ACCESSORY

(

or the symbol with a

Return IGN Switch To (0) Position

If the key won’t turn from LOCK

(

to ACCESSORY

(

, turn the key while moving the steering wheel left

and right. The steering wheel will unlock, allowing
the key to turn.

WARNING

Removing the key from the ignition switch
while driving locks the steering. This can
cause you to lose control of the vehicle.

Remove the key from the ignition switch
only when parked.

Manual transmission models

Continuously variable transmission models

All models

(

LOCK: Insert and remove the key in this

position.

(

ACCESSORY: Operate the audio system and

other accessories in this position.

(

ON: This is the position when driving.

(

START: This position is for starting the

engine. The switch returns to ON

(

when you

let go of the key.

215

Operating the Switches Around the Steering Wheel

ENGINE START/STOP Button

Continued

Co
ntrols

ENGINE START/STOP Button

■

Changing the Power Mode

Models with keyless access system

ENGINE START/STOP Button

ENGINE START/STOP

Button Operating Range

You can start the engine when the keyless remote is
inside the vehicle.

If the battery of the keyless remote is getting low, the
engine may not start when you push the

ENGINE

START/STOP

button. If the engine does not start,

refer to the following link.

If the Keyless Remote Battery is Weak

P. 742

The engine may also run if the keyless remote is close
to the door or window, even if it is outside the
vehicle.

ON mode:
The

ENGINE START/STOP

button is red when the

engine is running.

Operating Range

VEHICLE OFF (LOCK)

The button is off.
The steering wheel is locked.
The power to all electrical
components is turned off.

ACCESSORY

The button blinks (in red).
Operate the audio system and
other accessories in this position.

The button blinks (in red).
All electrical components can be
used.

Press the button without the
transmission in

(

Without
pressing the
brake pedal

Press the button with the
transmission in

(

Press the button.

Continuously Variable
Transmission

Manual Transmission

Without
pressing the
clutch pedal

Operating the Switches Around the Steering Wheel

ENGINE START/STOP Button

216

Co
ntrols

If you leave the vehicle for 30 to 60 minutes with the transmission in

(

(continuously variable transmission) and the power mode in ACCESSORY, the
vehicle automatically goes into the mode similar to VEHICLE OFF (LOCK) to avoid
draining the battery.

When in this mode:
The steering wheel does not lock.
You cannot lock or unlock doors with the remote transmitter or the keyless access
system.
Press the

ENGINE START/STOP

button three times to switch the mode to VEHICLE

OFF (LOCK).

■

Automatic Power Off

ENGINE START/STOP Button

If the power mode does not change from VEHICLE
OFF (LOCK) to ACCESSORY, press the

ENGINE

START/STOP

button while moving the steering

wheel left and right. The steering wheel will unlock,
allowing the mode to change.
Do not leave the power mode in ACCESSORY or ON
when you get out.

217

Operating the Switches Around the Steering Wheel

ENGINE START/STOP Button

Co
ntrols

When the power mode is set to any mode
other than OFF and you remove the keyless
remote from the vehicle and shut the door, an
alarm will sound. If the alarm continues to
sound, place the keyless remote in another
location.

■

When the power mode is in
ACCESSORY

The alarm will sound from outside the vehicle.

■

When the power mode is in ON

An alarm will sound both inside and outside
the vehicle. In addition, a warning indicator
will appear on the instrument panel.

■

Keyless Remote Reminder

Keyless Remote Reminder

When the keyless remote is within the system’s
operational range, and all the doors are closed, the
warning function cancels.

If the keyless remote is taken out of the vehicle after
the engine has been started, you can no longer
change the

ENGINE START/STOP

button mode or

restart the engine. Always make sure if the remote is
in your vehicle when you operate the

ENGINE

START/STOP

button.

Removing the keyless remote from the vehicle
through a window does not activate the warning
buzzer.

Do not put the keyless remote on the dashboard or in
the glove box. It may cause the warning buzzer to
activate. Under some other conditions that can
prevent the vehicle from locating the remote, the
warning buzzer may also activate even if the remote
is within the system’s operational range.

218

Operating the Switches Around the Steering Wheel

Ignition Switch and Power Mode Comparison

Co
ntrols

Ignition Switch and Power Mode Comparison

Ignition Switch
Position

LOCK

(

(with/without
the key)

ACCESSORY

(

START

(

Without Keyless
Access System

●

Engine is turned off and
power is shut down.

●

The steering wheel is
locked.

●

No electrical
components can be
used.

●

Engine is turned off.

●

Some electrical
components such as the
audio system and the
accessory power socket
can be operated.

●

Normal key position
while driving.

●

All electrical components
can be used.

●

Use this position to start
the engine.

●

The ignition switch
returns to the ON

(

position when you
release the key.

Power Mode

VEHICLE OFF
(LOCK)

ACCESSORY

START

With Keyless Access
System and

ENGINE

START/STOP

Button

Button-Off

●

Engine is turned off and
power is shut down.

●

The steering wheel is
locked.

●

No electrical
components can be
used.

Button-Blinking

●

Engine is turned off.

●

Some electrical
components such as the
audio system and the
accessory power socket
can be operated.

Button-
Blinking (engine is turned
off)
On (engine is running)

●

All electrical components
can be used.

Button-On

●

The mode automatically
returns to ON after the
engine starts.

Button is: Blinking

219

Operating the Switches Around the Steering Wheel

Turn Signals

Co
ntrols

Turn Signals

The turn signals can be used when the ignition
switch is in ON

(

■

(A): Turn signal

Push the lever up or down based on the
direction you want to turn, and the turn signal
will blink.

■

(B): One-touch turn signal

When you lightly push the lever up or down
and release it, the turn signal will blink 3
times.

If you lightly push the lever in the
opposite direction while it is blinking, the
blinking will stop.

*1: Models with the keyless access system have an

ENGINE START/STOP

button instead of an

ignition switch.

Turn Signals

The turn signal indicator on the instrument panel will
blink when the external turn signal blinks.

Indicators

P. 98

(A)

(B)

(A)

220

Operating the Switches Around the Steering Wheel

Light Switches

Co
ntrols

Light Switches

Rotating the light switch turns the lights on
and off, regardless of the power mode setting
or position of the ignition switch.

■

High beams

Push the lever forward until you hear a click.

■

Low beams

When in high beams, pull the lever back to
return to low beams.

■

Flashing the high beams

Pull the lever back, and release it.

■

Lights off

Turn the lever to

OFF

either when:

•

The shift lever is in

(

. (continuously

variable transmission models)

•

The parking brake is applied.

To turn the lights on again, turn the lever to

OFF

to cancel the lights off mode. Even if you

do not cancel the lights off mode, the lights
come on automatically when:

•

The transmission is taken out of

(

(continuously variable transmission models)
and the parking brake is released.

•

The vehicle starts to move.

■

Manual Operation

Light Switches

If you remove the key from the ignition switch while
the lights are on, a chime sounds when the driver’s
door is opened.

If you leave the power mode in VEHICLE OFF (LOCK)
while the lights are on, a chime sounds when the
driver’s door is opened.

When the lights are on, the lights on indicator in the
instrument panel will be on.

Indicators

P. 109

Do not leave the lights on when the engine is off
because it will cause the battery to discharge.

Your vehicle is equipped with the automatic
headlight adjusting system that automatically adjusts
the vertical angle of the low beam headlights. If you
find a significant change in the vertical angle of the
headlights, there may be a problem with the system.
Have your vehicle checked by a dealer.

Models without keyless access system

Models with keyless access system

All models

High Beams

Flashing the high beams

Low Beams

Turns on position, tail, and rear
licence plate lights

Turns on headlights, position,
tail, and rear licence plate lights

Honda CR-V (2022 year). Manual in english - page 13