325

3. Engine Hood Adjustment

Fix the engine hood to the engine hood hinge with bolts. the engine hood in vertical direction through the hinge

hole. Vertically adjust the front by adjusting the engine hood bumper and adjust the engine hood master lock

striker. The clearance tolerance is 1.0 mm-3.0 mm, while the flatness tolerance is 0 mm-1.0 mm.

(1) Open the engine hood

(2) Loose the bolt between the engine hood and the hinge

(3) Adjust the clearance between the engine hood and the front fender. Loose the bolt and move the engine

hood for adjustment.

(4) Close the engine hood

(5) Check for alignment

(6) Open the engine hood and adjust it as specified

(7) Adjust the engine hood bumper

(8) Check for alignment

(9) Adjust the engine hood master lock striker:

Loose 3 pin bolts on the engine hood lock. Move the engine hood lock for adjustment.

(10) T ighten the bolt between the engine and the hinge.

(11) Close the engine hood

4.Processing The Brace

Notice

• The air in the brace is of no color, no taste and no

poison.

(1) Wear the eye protection.

(2) Level the brace.

(3) Cut the brace with the hack saw as shown in the figure on

the right.

(4) Bleed the air from the brace

(5) Abandon the brace

326

(III) Outside Rear View Mirror

Attach the outside rear view mirror to the left and right doors. Integrate the outside rear view mirror with the

body smoothly using specially designed rubber bushing to make it a whole. The forward and rearward folding

of the rear view mirror will not be affected after being knocked. It is also a major way to reduce the whole

vehicle's air resistance coefficient.

Attach the lens to the plate with double sided adhesive tape. The plate is connected to the rear view mirror

case with the ball hinge to prevent fragment from splashing when it is broken, which may result in injury and

it is convenient to replace the broken lens. Pry the plate from the ball socket with the tool when the lens is

broken for replacement and press the new one into the ball socket. The case overturn force is designed to be

30N, enabling it liable to overturn when impacted by person or object and hence reducing the mutual damage.

The adjust handle of the outside rear view mirror is designed to be built in the vehicle to facilitate the

operator's direction adjustment. The optional flat mirror is generally selected for driver side to ensure the

sense of reality and distance. Spherical mirror is used for front passenger side to enlarge the rear field of

vision. In addition, outside rear view mirror has also the feature of electrical heating and defogging.

Notice

When folding the outside rear view mirror, be careful not to put your finger between the outside

rear view mirror and the mirror foot to avoid being crushed!

Replace the Rear View Mirror

Removal

1. Remove battery negative cable.

2. Remove the inside trim.

3. Disconnect electric outside rear view mirror connector.

4. Remove screw and outside rear view mirror retaining clip.

5. Remove electric outside rear view mirror.

6. The installation is in the reverse order of the removal.

Installation

1. Position the rear view mirror on the door

2. Tighten the screw from left lower side screw clockwise

Tighten

Tighten the outer rear view mirror screw to 1.5 N.M¡«2 N.M

3. Install rear view mirror inside trim cover

4. Install rear view mirror inner adjust handle

327

(IV) Rear trunk Lid

Component View:

1.Rear trunk Lid Hinge Pin

2.Rear trunk Lid Hinge Retainer

3.Rear trunk Lid Hinge Retainer

Mounting Nut

4.Rear trunk Door Hinge  Cushion

5.Rear trunk Lid Outer Panel And Reinforcement

Assembly

6.Geely Logo

7.Rear License Plate Assembly

8.Rear License Plate Assembly

Mounting Nut

9.Rear trunk Lid Weatherstrip

10.Rear trunk Lid inside Trim Board

1 1 . R e a r

trunk Lid Cushion

12.Rear trunk Door Lock Cylinder  Assembly 13.Rear trunk Lid inside Trim Board Clip

14.Rear trunk Lid Hinge Attaching Bolt

15.Rear trunk Door Lock Cable Assembly

1 6 . R e a r

trunk Door Oil Filler Cable  Assembly

17.Rear trunk Lid Hinge 18.Rear trunk Lid Spring

328

1.Rear trunk Lid Removal/Installation

Warning

It is dangerous to remove the rear trunk lid spring before supporting the rear trunk lid. The rear
trunk lid may drop and result in body injury. Fully open the rear trunk lid, support the rear trunk
lid before removing the brace.

Remove rear trunk lid under the help of the assistant.

(1) Disconnect the negative (--) terminal cable from the battery;

(2) Disconnect rear trunk wire harness connector. Pull the rear trunk lid wire harness out from the rear

trunk;

(3) Remove rear trunk door lock cylinder assembly. Pull out the rear trunk door lock cable;

(4) Remove rear trunk lid spring;

(5) Remove rear trunk lid hinge connecting bolt. Remove the rear trunk lid;

(6) Remove rear trunk lid hinge seat mounting nut. Remove the rear trunk lid hinge seat and the rear trunk lid

hinge

(7) Remove rear trunk door oil filler cable assembly;

(8) Remove cushion;

(9) Remove rear trunk lid hinge pin. Remove rear trunk lid hinge from the bracket;

(10)

Remove rear trunk lid weatherstrip;

(11)

Remove rear trunk lid inside trim board clip, Remove rear trunk lid inside trim board;

(12)

Remove rear license plate assembly mounting nut , Remove rear license plate assembly;

(13)

The installation is in the reverse order of the removal.;

(14)

Adjust the rear trunk lid. (See rear trunk lid adjustment)

2.Rear trunk Lid Adjustment

(1) Measure the clearance and height between the rear trunk lid and vehicle body.

(2) Loose the rear trunk lid hinge mounting bolt or the rear trunk latch mounting screw and reinstall the rear

trunk lid if it is not as specified.

Clearance

a: 3.74mm

b: 1.0mm

c: 4.0mm

(3) Tighten the rear trunk lid hinge bolt;

(4) Close the rear trunk lid