321

(IV) Rear inside trim

1

Inner rear view mirror

10

Rear doorinside trim

2

Interior lamp

11

C- pillar upper inside trim

Rear seat belt buckle

(See rear seat belt buckle

removal/installation) rear trunk

inside trim

4

Sun visor

13

Rear trunk lower trim cover

5

B- pillar upper inside trim

14

Lower rear trim assembly

Rear seat

(See rear seat removal/installation)

Front seat belt

Rear seat belt

(See front seat belt

removal/installation)

(See Rear seat belt

removal/installation)

(See seat belt inspection)

(See seat belt inspection)

8

B- pillar lower inside trim

17

Rear door sill inside trim

9

Safe handle

18

Carpet & sound insulator

7

16

3

A- pillar inside trim

12

6

Roof inside trim

15

322

Section 2 Inside & Outside Trim and Accessories Removal and

Installation

(I) Front Bumper

The structure is as shown in the figure below:

1. Front Bumper

2.Front Bumper Fixed Screw

3.Secondary Bumper Assembly Upper Buckle and Plug

4.Mounting Plate Cross Head Counter Sunk Self-tapping Screw

5.Mounting Plate Cross Head

Counter Sunk Self-tapping Screw

6.Front Bumper Mounting  Bracket to Body  Bolt

7.Front Bumper

Mounting Bracket Sub-assembly

8.  Secondary Bumper Assembly

9.Front Bumper Mounting

Bracket to Secondary Bumper Assembly Bolt

10.Front Bumper  Cushion

1 1.Secondary Bumper

Assembly Lower Buckle and Plug

12.License Mounting Plate Assembly

13.Secondary Bumper As-

sembly Lower Connecting Bolt 14.Front Bumper Mounting Plate Seat

15.Mounting Plate Seat Bolt

16.Front Bumper Mounting Plate

323

1. Front Bumper Removal and Installation

(1) Disconnect the negative (--) terminal cable from the battery. Disconnect fog lamp wire;

(2) Remove the mudguard skirt to front bumper clip;

(3) Remove the attaching bolt of the the front fender and panel and the front bumper sub-assembly;

(4) Remove the front bumper set screw and the clip. Remove the front bumper mounting plate and the

positioning screw of the seat;

(5) Remove the bolt which connecting front bumper mounting bracket with the vehicle body;

(6) Pull the front bumper assembly and the secondary bumper assembly together out of the vehicle body.

Separate the front bumper mounting bracket from the rail, front bumper mounting plate from the front

bumper mounting plate seat;

(7)  Remove the front bumper mounting plate seat from the vehicle body;

(8) Remove the secondary bumper assembly and the front bumper mounting bracket sub-assembly;

(9) Remove front bumper mounting plate;

(11)Remove front bumper cushion. Remove the front license plate. Remove the mounting plate assembly;

(12)Remove fog lamp;

(13)The installation is in the reverse order of the removal.

2.Notice For Removal Of The Front Bumper

(1) Pull the front bumper to separate it from the bumper rail.

(2) Uniformly pull it by force to prevent the front bumper mounting plate and seat from damage.

Warning

If the front bumper is only separated from the bumper rail on one side, the bumper may drop

and result in body hurt. Be careful not to drop the bumper when separating the front bumper

from the bumper rail.

3.Notice for installation of the front bumper

(1) Press the front bumper connecting part to the vehicle body and connect the rear bumper mounting

bracket assembly with the bumper rail.

(2) Be sure to insert the front bumper mounting plate seat into the bumper mounting plate.

324

(II) Engine Hood

Engine Hood Removal / Installation

For engine hood installation, see the figure

1. Removal

Warning

• It is dangerous to remove the engine hood without support. The engine hood may drop and

result in body injury. Work with at least one assistant when removing the engine hood and

should follow the procedures below:

1

Disconnect windshield washer hose.

2

Lift up the engine hood and support it with the spring brace;

3

Remove 2 spring braces under the help of the assistant to prevent the engine hood from dropping down

and resulting in body injury;

4

The assistant lifts the engine hood, removes the engine hood hinge bolt and the engine hood;

5

Remove the ventilator louver and remove the hinge arm;

6

Remove the hinge arm bracket attach bolt. Remove the hinge arm bracket from the body;

7

Remove the engine hood lock;

8

Remove the engine hood lock control cable.

2.Installation

1

The installation is in the reverse order of the removal;

2

Adjust the engine hood;

Engine Hood

Gas Spring Brace

Engine Hood Hinge 

Engine Hood Lock Control Cable

Engine Hood Lock

Engine Hood Installation Illustration