Next

Step 8

System normal.

11.8.7.6 Sunroof Can Not Close

Schematic:

Refer to 

11.8.7.4

 

Sunroof Inoperative

.

Diagnostic Steps:

Step 1

Send a ground signal to the sunroof module.

(a)

Remove the sunroof switch. Refer to 

11.8.8.3

 

Sunroof Switch

Assembly Replacement

.

(b)

Connect the sunroof antenna switch harness connector
RF06 terminal No.2 and body ground with a suitable antenna.

Confirm the sunroof motor is working.

Yes

Go to step 5

No

Step 2

Check resistance between the sunroof switch and the sunroof module.

(a)

Disconnect the sunroof module assembly harness
connector.

(b)

Measure resistance between the sunroof module harness
connector RF08 terminal No.4 and the sunroof switch wiring
harness connector RF06 terminal No.2 with a multimeter.
Resistance Standard Value: Less than 1 Ω

Is the resistance specified value?

Yes

Go to step 4

No

Step 3

Repair the wiring harness between the sunroof switch and the sunroof module

Is the sunroof working properly?

Yes

System normal

No

Step 4

Replace the sunroof motor.

(a)

Replace the sunroof motor. Refer to 

11.8.8.2

 

Sunroof Motor

Replacement

.

Confirm the repair completed.

Yes

System normal

Body Electric

Sunroof

11-313

No

Step 5

Check the circuit between the sunroof switch harness connector RF06 and body ground.

(a)

Remove the sunroof switch. Refer to 

11.8.8.3

 

Sunroof Switch

Assembly Replacement

.

(b)

Measure resistance between the sunroof switch harness
connector RF06 terminal No.4 and body ground with a
multimeter.
Standard Resistance: Less than 1 Ω
Is the resistance specified value?

Yes

Go to step 7

No

Step 6

Repair the circuit between the sunroof switch harness connector RF06 and body ground.

Confirm the repair completed.

Yes

System normal

No

Step 7

Replace the sunroof switch.

(a)

Install a new sunroof switch.. Refer to 

11.8.8.3

 

Sunroof

Switch Assembly Replacement

.

Confirm the repair completed.

Next

Step 8

System normal.

11.8.7.7 Sunroof Anti-trap Function Inoperative

Schematic:

Refer to 

11.8.7.4

 

Sunroof Inoperative

.

Diagnostic Steps:

Step 1

Carry out the sunroof initialization.

Is the sunroof working properly?

Yes

System normal

No

Step 2

Replace the sunroof switch assembly.

(a)

Install a new sunroof switch. Refer to 

11.8.8.3

 

Sunroof Switch

Assembly Replacement

.

Is the sunroof working properly?

11-314

Sunroof

Body Electric

Next

Step 3

System normal.

11.8.7.8 Sunroof Can Not Operate Intermittently

Schematic:

Refer to 

11.8.7.4

 

Sunroof Inoperative

.

Fault Symptom Table:

Symptoms

Suspected Faulty Part

Repair Procedure

Insulation Inner Layer Wire Poor
Connection

Sunroof  Module  and  The  Sunroof  Switch
Slide Switch

Refer to 

11.8.7.5

 

Sunroof Can Not Open

.

Harness Connector Male and Female
Terminals Poor Connection

1. Sunroof Switch

2. Sunroof Motor Wire Harness Connector

3. Sunroof Switch Harness Connector

4. Sunroof Motor

1. Clean  connector  male  and  female

terminals.

2. Replace  the  sunroof  switch.  Refer  to

11.8.8.3

 

Sunroof  Switch  Assembly

Replacement

.

3. Replace the wiring harness.

4. Replace  the  sunroof  motor.  Refer  to

11.8.8.2

 

Sunroof Motor Replacement

.

Ground Poor Connection

G7A Ground

 
1. Ground Fasteners.

2. Clean the ground connection.

Sunroof Switch Poor Connection

1. Slide Switch

2. Tilt Switch

Replace  the  sunroof  switch.  Refer  to

11.8.8.3

 

Sunroof 

Switch 

Assembly

Replacement

.

Body Electric

Sunroof

11-315

11.8.8 Removal and Installation
11.8.8.1 Sunroof Glass Replacement

Removal Procedure

FE11-1530b

1.

Tilt the sunroof for access to remove the sunroof retaining
bolts and remove the left side sunroof retaining bolts.

FE11-1531b

2.

Remove the right side sunroof retaining bolts.

FE11-1532b

3.

Pull  the  sunroof  window  upward  to  remove  the  sunroof
window glass.

11-316

Sunroof

Body Electric