FE06-0041b

1.

Install the brake hose to the brake cylinder and tighten the
bolts.

Torque: 16 Nm (Metric) 11.9 lb-ft (US English)

FE06-0042b

2.

Fix the brake hose.

FE06-0043b

3.

Connect the brake hose and the brake pipe and tighten
the bolt, install the spring.

Torque: 16 Nm (Metric) 11.9 lb-ft (US English)

4.

Install the wheels.

Note

Refer to "Adding Fluid to the Brake System Notice"
in "Warnings and Notices".

5.

Fill the brake fluid.

6.

Check fluid leak.

Note

Front  left  and  right  brake  hose  replacement  is
similar.

Brake System

Hydraulic Brake

6-41

6.4.5.4 Brake Hose Replacement (Rear)

Removal Procedure:

Note

Refer  to  "Brake  Fluid  Effects  on  Paint  and  Electrical
Components Notice in ""Warnings and Notices".

1

2

FE06-0044b

1.

Drain the brake fluid.

2.

Lift and support the vehicle. Refer to

1.3

 

Lifting and Jacking

the Vehicle

.

3.

Remove 

the 

rear 

wheels, 

taking 

into

account

4.4.5.1

 

Wheel Replacement

.

4.

Remove  the  bolts,  separate  the  brake  pipe  and  brake
hose (1).

5.

Pull  out  the  spring,  pull  out  brake  hose  (2)  from  the
bracket.

FE06-0045b

6.

Remove the bolts, disconnect the the brake hose from the
rear brake slave cylinder.

7.

Remove the rear brake hose.

Installation Procedure:

Warning!

Refer  to  "Brake  Pipe  Replacement  Warning"  in
"Warnings and Notices".

6-42

Hydraulic Brake

Brake System

FE06-0046b

1.

Install  the  brake  hose  to  the  rear  brake  cylinder  and
tighten the bolts.

Torque: 16 Nm (Metric) 11.9 lb-ft (US English)

FE06-0047b

2.

Connect the brake hoses and the brake pipe and tighten
the bolts, install the spring.

3.

Install the wheels.

Note

Refer to "Brake Fluid Effects on Paint and Electrical
Components Notice" in "Warnings and Notices".

4.

Fill the brake fluid.

5.

Check brake fluid leak.

Note

Rear brake left and right brake hose replacement is
similar.

6.4.5.5  Hydraulic  Brake  System  Exhaust
Procedure

Note

Refer to "Adding Fluid to the Brake System Notice" in
"Warnings and Notices".

Note

Air can not be discharged in hydraulic brake regulator
manually.  If  the  air  enters  the  ABS  hydraulic  brake
regulator or the installed ABS hydraulic brake adjuster is
not  fully  filled  with  fluid,  using  a  scan  tool  to  exhaust
brake  system  air.  The  factory  ABS  hydraulic  brake
adjuster is fully filled with fluid, and air is exhausted. In
the normal service regulator procedure, the air will not
enter  the  ABS  hydraulic  brake  regulator,  in  this  case,
carry out the manual exhaust program.

Brake System

Hydraulic Brake

6-43

Note

If it is not suspected that air enters the master cylinder,
start from step 5. Otherwise, start from step 2.

Note

Refer  to  "Brake  Fluid  Effects  on  Paint  and  Electrical
Components Notice" in "Warnings and Notices".

FE06-0048b

1.

Shut  down  the  engine,  press  the  brake  pedal  several
times until the completely eliminate the booster pressure.

2.

Fill  the  brake  fluid  to  the  master  cylinder  tank.  in  the
exhaust operations, leave the master cylinder tank fluid
level at least more than half.

3.

Slowly  press  the  brake  pedal  to  the  end,  and  hold  the
position.

FE06-0049b

4.

Loosen  one  brake  master  cylinder  pipe,  tighten  the
connection when the brake fluid flows out.

Torque: 16 Nm (Metric) 11.9 lb-ft (US English)

5.

Loosen the other brake master cylinder pipe, tighten the
connection when the brake fluid flows out.

Torque: 16 Nm (Metric) 11.9 lb-ft (US English)

6.

Repeat steps 2 to step 5 three to four times.

FE06-0050b

7.

Remove  the  air  discharge  screw  dust  cover,  connect  a
transparent  tube  to  the  right  rear  brake  caliper  air
discharge screw. The tube is immersed in a transparent

6-44

Hydraulic Brake

Brake System