Ford F-650 / 750 (2022 year). Manual in english

At Every Oil Change Interval as Indicated by the Information Display

Inspect the air filter restriction gauge. Replace the filter if necessary.

Inspect the automatic transmission fluid level. Consult an authorized dealer for
requirements.

Inspect the brake pads, shoes, rotors, drums, brake linings, hoses and the parking brake.

Inspect the engine and secondary coolant concentration, freeze-point protection, level
and hoses.

Inspect the exhaust system and heat shields.

Inspect the steering linkage, ball joints, suspension, tie-rod ends, driveshaft and the U-
joints. Lubricate any components that have grease fittings.

Inspect front oil hubs for leaks and check fluid level through hub cap sight glass.

Do not exceed one year/10,000 mi (16,000 km) or 350 engine hours between service

intervals.

Reset the Intelligent Oil-Life Monitor after engine oil and filter changes. See

Oil Change

Indicator Reset

(page 226).

Rotate the front wheels on vehicles with dual rear wheels when specified. Only rotate

the rear wheels if you notice unusual wear.

Brake Fluid Maintenance

Change the brake fluid.

Every 3 Years

Perform this maintenance item every 3 years. Do not exceed the designated time for

the interval.

Brake fluid servicing requires special equipment available at your authorized dealer.

Other Maintenance Items

Replace the engine-mounted and frame-mounted fuel

filters.

Every 22,000 mi
(36,000 km)

Inspect the engine and secondary cooling system coolant
concentration, freeze-point protection, additive, corrosion
inhibitor, strength, coolant level, and hoses. Add coolant

additive if necessary.

Every 30,000 mi
(48,000 km)

329

Scheduled Maintenance

Other Maintenance Items

Note: When adding coolant additive, do not exceed the
specified maximum of 47 fl oz (1.4 L) for the engine and
20 fl oz (473 ml) for the secondary cooling system. Oper-
ating the engine with excessive coolant additive may cause
overheating which could lead to severe, permanent engine
damage.

Replace the air inlet foam filter.

Every 45,000 mi
(72,000 km)

Inspect the accessory drive belt or belts.

At 90,000 mi
(144,000 km)

Change the rear axle fluid. See

Special Operating

Conditions Scheduled Maintenance

(page 331).

At 100,000 mi
(160,000 km)

Change the automatic transmission fluid and filter. Consult
an authorized dealer for requirements.

Every 150,000 mi
(240,000 km)

Replace the accessory drive belt or belts if not replaced
within the last 100,000 mi (160,000 km).

Replace the front wheel bearings and seals.

Change the engine and secondary cooling system coolant.

At 200,000 mi
(320,000 km)

You can perform these maintenance items within 3,000 mi (4,800 km) of the last oil

change. Do not exceed the designated distance for the interval.

Every 22,000 mi (36,000 km) or as indicated by the information display.

Every 30,000 mi (48,000 km), 1200 engine hours or as indicated by the information

display.

Perform follow-up inspections every 15,000 mi (24,000 km) after the initial inspection.

Replace the belt or belts at 150,000 mi (240,000 km).

Change the fluid again at 150,000 mi (240,000 km).

Initial replacement at 10 years or 200,000 mi (320,000 km), then every five years or

100,000 mi (160,000 km).

330

Scheduled Maintenance

SPECIAL OPERATING
CONDITIONS SCHEDULED
MAINTENANCE

Gasoline Engines

If you operate your vehicle

primarily

in any

of the following conditions, you need to
perform extra maintenance as indicated.
If you operate your vehicle

occasionally

under any of these conditions, it is not
necessary to perform the extra
maintenance. For specific
recommendations, see your dealership
service advisor or technician.

Towing a Trailer

Inspect and lubricate the U-joints.

Inspect frequently, service
as required

See axle maintenance items under

Exceptions

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.

Every 5,000 mi (8,000 km)

Change the engine oil and filter.

Every 5,000 mi (8,000 km)
or six months

Inspect and lubricate U-joints.

Rotate the tires

and inspect them for wear, and measure

the tread depth.

Every 7,500 mi (12,000 km)

Replace the spark plugs.

Every 60,000 mi
(96,000 km)

Rotate the front wheels on vehicles with dual rear wheels when specified. Only rotate

the rear wheels if you notice unusual wear.

Extensive Idling or Low-speed Driving for Long Distances, as in Heavy Commercial Use

(Such as Delivery, Taxi, Patrol Car or Livery)

Replace engine air filter.

Inspect frequently, service
as required

Inspect the brake system.

Every 5,000 mi (8,000 km)

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.

Lubricate the control arm and steering ball joints if
equipped with grease fittings.

Inspect and lubricate U-joints.

Every 5,000 mi (8,000 km)
or six months

331

Scheduled Maintenance

Extensive Idling or Low-speed Driving for Long Distances, as in Heavy Commercial Use

(Such as Delivery, Taxi, Patrol Car or Livery)

Change the engine oil and filter.

Every 5,000 mi (8,000 km),
six months or 200 engine
hours

Rotate the tires

and inspect them for wear, and measure

the tread depth.

Every 7,500 mi (12,000 km)

Replace the spark plugs.

Every 60,000 mi
(96,000 km)

Rotate the front wheels on vehicles with dual rear wheels when specified. Only rotate

the rear wheels if you notice unusual wear.

Operating in Dusty or Sandy Conditions (Such as Unpaved or Dusty Roads)

Replace the engine air filter.

Inspect frequently, service
as required

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.

Every 5,000 mi (8,000 km)

Change the engine oil and filter.

Every 5,000 mi (8,000 km)
or six months

Inspect and lubricate U-joints.

Rotate the tires

and inspect them for wear, and measure

the tread depth.

Every 7,500 mi (12,000 km)

Rotate the front wheels on vehicles with dual rear wheels when specified. Only rotate

the rear wheels if you notice unusual wear.

Off-road Operation

Inspect the steering linkage, ball joints and U-joints,
lubricate if equipped with grease fittings.

Inspect frequently, service
as required

Replace the engine air filter.

Change the engine oil and filter.

Every 5,000 mi (8,000 km)
or six months

332

Scheduled Maintenance

Off-road Operation

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.

Rotate the tires

and inspect them for wear, and measure

the tread depth.

Every 7,500 mi (12,000 km)

Rotate the front wheels on vehicles with dual rear wheels when specified. Only rotate

the rear wheels if you notice unusual wear.

Diesel Engine

If you operate your vehicle

primarily

in any

of the following conditions, you need to
perform extra maintenance as indicated.
If you operate your vehicle

occasionally

under any of these conditions, it is not
necessary to perform the extra
maintenance. For specific
recommendations, see your dealership
service advisor or technician.

Towing a Trailer or Using a Car-top Carrier

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

See the axle maintenance items under

Exceptions

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km) or six months,
600 engine hours

Inspect the coolant concentration, freeze-point protection
and additive, corrosion inhibitor strength. Add coolant
additive if necessary.

Every 30,000 mi
(48,000 km) or 1200 engine
hours

Flush and refill the coolant. Do not add coolant additive.

Every 60,000 mi
(96,000 km) or 2400
engine hours

Note:

When adding coolant additive, do not exceed the specified maximum of 47 fl oz

(1.4 L) for the engine and 20 fl oz (473 ml) for the secondary cooling system. Operating the
engine with excessive coolant additive may cause overheating which could lead to severe,
permanent engine damage.

Note:

After the initial coolant flush and fill at 60,000 mi (96,000 km) or 2400 engine

hours, flush and fill every 45,000 mi (72,000 km) or 1800 engine hours thereafter.

333

Scheduled Maintenance

Frequent or Extended Idling, Over 10 Minutes Per Hour of Normal Driving or Frequent

Low-speed Operation if You Use Your Vehicle for Stationary Operation

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
600 engine hours

Inspect the coolant concentration, freeze-point protection
and additive, corrosion inhibitor strength. Add coolant
additive if necessary.

Every 30,000 mi
(48,000 km) or 1200 engine
hours

Flush and refill the coolant. Do not add coolant additive.

Every 60,000 mi
(96,000 km) or 2400
engine hours

Note:

When adding coolant additive, do not exceed the specified maximum of 47 fl oz

Note:

After the initial coolant flush and fill at 60,000 mi (96,000 km) or 2400 engine

hours, flush and fill every 45,000 mi (72,000 km) or 1800 engine hours thereafter.

334

Scheduled Maintenance

Frequent Low-speed Operation, Consistent Heavy Traffic Under 25 mph (40 km/h) or

Long Rush-hour Traffic

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
600 engine hours

Inspect the coolant concentration, freeze-point protection
and additive, corrosion inhibitor strength. Add coolant
additive if necessary.

Every 30,000 mi
(48,000 km) or 1200 engine
hours

Flush and refill the coolant. Do not add coolant additive.

Every 60,000 mi
(96,000 km) or 2400
engine hours

Note:

When adding coolant additive, do not exceed the specified maximum of 47 fl oz

Note:

After the initial coolant flush and fill at 60,000 mi (96,000 km) or 2400 engine

hours, flush and fill every 45,000 mi (72,000 km) or 1800 engine hours thereafter.

335

Scheduled Maintenance

Sustained High-speed Driving at Gross Vehicle Weight Rating, Maximum Loaded Weight

for Vehicle Operation

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
600 engine hours

Inspect the coolant concentration, freeze-point protection
and additive, corrosion inhibitor strength. Add coolant
additive if necessary.

Every 30,000 mi
(48,000 km) or 1200 engine
hours

Flush and refill the coolant. Do not add coolant additive.

Every 60,000 mi
(96,000 km) or 2400
engine hours

Note:

When adding coolant additive, do not exceed the specified maximum of 47 fl oz

Note:

After the initial coolant flush and fill at 60,000 mi (96,000 km) or 2400 engine

hours, flush and fill every 45,000 mi (72,000 km) or 1800 engine hours thereafter.

Operating in Sustained Ambient Temperatures Below -9.4°F (-23°C) or Above 100.3°F

(38°C)

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
600 engine hours

Operating in Dusty or Sandy Conditions, Such as Unpaved or Dusty Roads

Rotate the tires

, inspect the tires for wear and measure

tread depth.

Every 7,500 mi (12,000 km)

Inspect the brake system pads and rotors.

Inspect the air filter restriction gauge. Replace the filter if
necessary.

336

Scheduled Maintenance

Operating in Dusty or Sandy Conditions, Such as Unpaved or Dusty Roads

Inspect the steering and suspension ball joints and tie rods.
Lubricate any grease fittings.

Change the engine oil and filter.

Every 7,500 mi (12,000 km),
six months or 300 engine
hours

Inspect and lubricate the U-joints.

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), 6 months or
600 engine hours

Replace the air inlet foam filter.

Every 30,000 mi
(48,000 km)

Rotate the front wheels on vehicles with dual rear wheels when specified. Only rotate

the rear wheels if you notice unusual wear.

Reset the Intelligent Oil-Life Monitor after engine oil and filter changes.

Off-road Operation

Inspect functional holes in each leg of the twin exhaust
tips and the holes under the shield just inboard of the right
rear tire to make sure they are clean and clear of debris or
foreign materials. Refer to the Vehicle Care chapter of your
owner’s manual for more information.

As required

Inspect the steering and suspension ball joints and tie rods.
Lubricate any grease fittings.

Rotate the tires

, inspect the tires for wear and measure

tread depth.

Every 7,500 mi (12,000 km),
six months or 300 engine
hours

Inspect the brake system pads and rotors.

Inspect the air filter restriction gauge. Replace the filter if
necessary.

Change the engine oil and filter.

Every 7,000 mi (12,000 km)
or 300 engine hours

337

Scheduled Maintenance

Off-road Operation

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
600 engine hours

Replace the air inlet foam filter.

Every 30,000 mi
(48,000 km)

Rotate the front wheels on vehicles with dual rear wheels when specified. Only rotate

the rear wheels if you notice unusual wear.

Reset the Intelligent Oil-Life Monitor after engine oil and filter changes.

Using Biodiesel, up to and Including 20% Biodiesel (B20)

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
300 engine hours

Using Fuel Other Than Ultra-low Sulfur Diesel Fuel - Vehicles Operated Where Ultra-low

Sulfur Diesel Fuel is not Required or Available

Change the engine oil and filter.

Every 2,500 mi (4,000 km)
or three months (if using
high sulfur fuel with more
than 500 ppm sulfur)

Change the engine oil and filter.

Every 5,000 mi (8,000 km)
or six months (if using high
sulfur fuel with fewer than
500 ppm sulfur)

Exceptions

There are several exceptions to the Normal
Schedule:

338

Scheduled Maintenance

Rear Axle Maintenance

A rear axle fluid change or level check is
not required unless you suspect a leak or
the assembly has been submerged in
water. During long periods of trailer towing
with outside temperatures above 70°F
(21°C), and at wide-open throttle for long
periods above 45 mph (72 km/h), change
the rear axle fluid every 24,000 mi
(38,000 km) or three months, whichever
comes first.

California Fuel Filter Replacement

If you register your vehicle in California, the
California Air Resources Board has
determined that the failure to perform this
maintenance item does not nullify the
emission warranty or limit recall liability
before the completion of your vehicle's
useful life. We, however, urge you to have
all recommended maintenance services
performed at the specified intervals and
to record all vehicle service.

Hot Climate Oil Change Intervals

The normal oil change interval is 3,000 mi
(5,000 km) for gasoline vehicles operating
in the Middle East, North Africa,
Sub-Saharan Africa or locations with
similar climates using American Petroleum
Institute (API) oils Certified for Gasoline
Engines and displaying the API Certification
Mark. If API Certified Oils are not available,
then it is acceptable to use API SM or SN
oils. If API oils are not available, then the
oil change interval is 1,750 mi (3,000 km).

Engine Air Filter Replacement

The life of the engine air filter is dependent
on exposure to dusty and dirty conditions.
Vehicles operated in these conditions
require frequent inspection and
replacement of the engine air filter and
cabin air filter.

Diesel Particulate Filter

Over time, a slight amount of ash builds
up in the diesel particulate filter, which is
not removed during the regeneration
process. The filter may need to be replaced
with a new or remanufactured part at
approximately 250,000 mi (400,000 km).
Actual mileage varies depending on engine
and vehicle operating conditions.

In this case, the engine control system sets
a service light (wrench icon) to inform you
to bring your vehicle to the dealer for
service. If there are any issues with the
oxidation catalyst or particulate filter
system, a service light (wrench or engine
icon) sets by the engine control system to
inform you to bring your vehicle into a
dealer for service.

339

Scheduled Maintenance

Ford F-650 / 750 (2022 year). Manual in english - page 21