|
|
|
152
❑
Using the “SEEK” function
This feature on your radio allows you to
automatically select listenable stations up or
down the frequency band. Press the top
a
half of the “SEEK” button to select the next
listenable station up the frequency band.
Press the bottom
b
half of the button to
select the next listenable station down the
frequency band. By pressing and holding the
button, listenable stations can be passed over
to reach the desired station.
❑
Using the “SCAN/TUNE” button to scan
radio stations
Pressing the “SCAN/TUNE” button once
enters the scan mode (display will indicate
“SCN”). Pushing the top
a
half of the
“SEEK” button will begin the scan mode up
the frequency band, stopping on each
listenable station for approximately five
seconds. Pushing the bottom
b
half of the
“SEEK” button will begin the scan mode
down the frequency band, again stopping on
each listenable station for approximately five
seconds.
To stop the scan mode on the presently
sampled station press the “SCAN/TUNE”
button again.
❑
Setting the Station Memory Preset buttons
Your radio is equipped with 5 station memory
buttons. These buttons can be used to select up
to 5 preset AM stations and 10 FM stations (5 in
FM1 and 5 in FM2). Follow the easy steps below
to set these buttons to the desired frequencies.
1.
Select a band, then select a frequency.
153
2.
Press one of the memory buttons and hold
the button until the sound returns. That
station is now held in memory on that
button.
3.
Follow the two steps above for each station
memory preset button you want to set.
NOTE:
If the vehicle’s battery is disconnected,
the clock and station memory preset
buttons (if programmed in auto mode)
will need to be reset.
❑
Using the Automatic Memory Load feature
You can activate the
Auto Memory Load
feature by pressing and holding the “AUTO
PRESET” button
for approximately three
seconds
. Auto Memory Load sets all memory
buttons in AM, FM1 and FM2 sequentially by
seeking out the first five strong stations for
the respective band and storing them in
memory buttons 1-5. (FM2 will store the
second set of strong stations from the FM
band.)
With Auto Memory Store, you can
continually set strong stations into your
memory buttons without losing your existing
memory presets, which is especially handy
while traveling. Your radio will automatically
set your memory buttons to the strong local
stations so you don’t have to continually
manually tune to existing stations.
Activate Auto Memory Store by pushing the
“AUTO PRESET” button once. Your radio
will set the first five strong stations of the
band you are in (AM, FM1 or FM2) into the
memory buttons. The display will show
“AUTO”, then run through the frequencies,
stopping momentarily on the stations being
set into the memory buttons. The radio is
154
now in the “AUTO” mode and this display
will show “AUTO” each time a preset is
activated.
NOTE:
If there are fewer than five strong
stations in the frequency band, the
remaining unfilled buttons will store
the last strong station detected on the
band.
After all stations have been filled, the radio
will begin playing the station stored on
memory button 1.
To deactivate the Auto Memory Store mode
and return to the manually-set memory
button stations (or those stations set using
Auto Memory Load), simply push the
“AUTO PRESET” button. Display will show
“AUTO” then “OFF”. The next time Auto
Memory Store is activated on that band, the
radio will store the next set of five strong
stations.
Using the “AUDIO” button to adjust the
tone balance and speaker output
❑
Increasing or decreasing bass response
Push the “AUDIO” button repeatedly until
the display reads “BASS.” Push the “+” side
of the “VOL” button to increase bass (more
“lows”), and push the “-” side to decrease
bass (less “lows”).
❑
Increasing or decreasing treble response
Push the “AUDIO” button repeatedly until
the display reads “TREB.” Push the “+” side
of the “VOL” button to increase treble (more
“highs”), and push the “-” side to decrease
treble (less “highs”).
155
❑
Adjusting speaker balance
Balance control allows you to adjust the
sound distribution between the right and left
speakers. Push the “AUDIO” button
repeatedly until the display reads “BAL.”
Push the “+” side of the “VOL” button to
shift the sound to the right speakers, and
push the “-” side to shift the sound to the
left speakers.
❑
Adjusting speaker fader
Fade control allows you to adjust the sound
distribution between the front and rear
speakers. Push the “AUDIO” button
repeatedly until the display reads “FADE.”
Push the “+” side of the “VOL” button to
shift the sound to the front speakers, and
push the “-” side to shift the sound to the
rear speakers.
NOTE:
Illuminated bars in the display show
relative levels of bass and treble and
positions of speaker balance and fader
functions after adjustments are made,
then revert to volume level set.
Clock operation
When in the radio mode, push the “CLOCK”
button to switch from radio frequency to clock.
Only the clock numerals will be displayed in the
clock mode — there is no A.M./P.M. indication.
When in the clock mode, the time will be
displayed until the button is pushed again.
However, if you retune the radio while it is in
the clock mode, the new radio frequency will be
displayed for approximately ten seconds and
then change back to clock.
|
|
|