Dodge Viper SRT-10 (ZB). Manual - part 354

TEST

ACTION

APPLICABILITY

Disconnect the Body Control Module C2 and C3 connectors.
Measure the resistance between ground and the Driver Door Switch Mux circuit in
the BCM C3 connector.
Is the resistance below 10000.0 (10K) ohms?

All

Yes

→ Repair the Driver Door Switch Mux circuit for a partial short to

ground
Perform BODY VERIFICATION TEST - VER 1.

→ Go To 4

Disconnect the Body Control Module C2 and C3 connectors.
Measure the resistance between the Driver Door Switch Mux circuit and the Driver
Door Switch Return circuits in the BCM C2 and C3 connectors.
Is the resistance below 10000.0 (10K) ohms?

All

Yes

→ Repair the Driver Door Switch Mux circuit for a partial short to

the Driver Door Switch Return circuit.
Perform BODY VERIFICATION TEST - VER 1.

→ Replace the Body Control Module.

Perform BODY VERIFICATION TEST - VER 1.

309

POWER DOOR LOCKS/RKE

DRIVER INTERIOR DOOR HANDLE SWITCH STUCK —

Continued

Symptom:

PASSENGER DOOR LOCK CIRCUIT SHORT TO GROUND

When Monitored and Set Condition:

PASSENGER DOOR LOCK CIRCUIT SHORT TO GROUND

When Monitored:

At all times when battery power is supplied to the Body Control

Module.

Set Condition:

When the BCM senses voltage on the passenger door switch mux circuit

below 0.7 volts for over 10 seconds.

POSSIBLE CAUSES

DTC PRESENT

PASSENGER DOOR SWITCH MUX CIRCUIT SHORT TO GROUND

PASSENGER DOOR LOCK SWITCH SHORT TO GROUND

PASSENGER INTERIOR DOOR HANDLE SWITCH SHORT TO GROUND

PASSENGER EXTERIOR DOOR HANDLE SWITCH SHORT TO GROUND

PASSENGER DOOR SWITCH MUX WIRE SHORT TO THE DRIVER DOOR SWITCH RETURN.

BODY CONTROL MODULE - PASSENGER DOOR SWITCH MUX CIRCUIT SHORT TO GROUND

TEST

ACTION

APPLICABILITY

NOTE: When this code is present, the VTSS indicator will stay on solid during the
arming process.
With the DRBIII

t, record and erase DTC’s.

Cycle the ignition switch from ON to OFF to ON.
With the DRBIII

t, read DTC’s.

Lower the passenger door window.
Remove the key and operate all the passenger door switches several times while
monitoring the DRBIII

Wait 10 seconds.
Does the DRBIII

t display PASSENGER DOOR LOCK CIRCUIT SHORT TO

GROUND?

All

Yes

→ Go To 2

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors for an intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.

Disconnect the Body Control Module C3 and C4 connectors.
Measure the resistance between ground and the Passenger Door Switch Mux circuit
in the BCM C3 connector.
Is the resistance below 300.0 ohms?

All

Yes

→ Repair the Passenger Door Switch Mux circuit for a short to

ground
Perform BODY VERIFICATION TEST - VER 1.

→ Go To 3

310

POWER DOOR LOCKS/RKE

TEST

ACTION

APPLICABILITY

Disconnect the Body Control Module C3 and C4 connectors.
Measure the resistance between the Passenger Door Switch Mux circuit and the
Passenger Door Switch Return circuits in the BCM C3 and C5 connectors.
Is the resistance below 200.0 ohms?

All

Yes

→ Go To 4

→ Go To 8

Disconnect the Body Control Module C3 and C4 connectors.
Disconnect the Passenger Door Lock Switch connector.
Measure the resistance between the Passenger Door Switch Mux circuit and the
Passenger Door Switch Return circuit in the BCM C3 and C5 connectors.
Is the resistance below 200 ohms?

All

Yes

→ Go To 5

→ Replace the Passenger Door Lock Switch.

Perform BODY VERIFICATION TEST - VER 1.

Disconnect the Body Control Module C3 and C4 connectors.
Disconnect the Passenger Interior Door Handle Switch connector.
Measure the resistance between the Passenger Door Switch Mux circuit and the
Passenger Door Switch Return circuit in the BCM C3 and C5 connectors.
Is the resistance below 200 ohms?

All

Yes

→ Go To 6

→ Replace the Passenger Interior Door Handle Switch.

Perform BODY VERIFICATION TEST - VER 1.

All

Yes

→ Go To 7

→ Replace the Passenger Exterior Door Handle Switch.

Perform BODY VERIFICATION TEST - VER 1.

If there are no possible causes remaining, view repair.

All

Repair

Repair the Passenger Door Switch Mux wire for a short to the
Passenger Door Switch Return wire.
Perform BODY VERIFICATION TEST - VER 1.

If there are no possible causes remaining, view repair.

All

Repair

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

311

POWER DOOR LOCKS/RKE

PASSENGER DOOR LOCK CIRCUIT SHORT TO GROUND —

Continued

Symptom:

PASSENGER DOOR LOCK SWITCH STUCK

When Monitored and Set Condition:

PASSENGER DOOR LOCK SWITCH STUCK

When Monitored:

At all times when battery power is supplied to the Body Control

Module.

Set Condition:

When the BCM senses a lock or unlock input on the Passenger Door

Switch Mux circuit for over 10 seconds, this code will set.

POSSIBLE CAUSES

DTC PRESENT

PASSENGER DOOR LOCK SWITCH SHORTED

PASSENGER DOOR SWITCH MUX CIRCUIT SHORT TO GROUND

PASSENGER DOOR SWITCH MUX CIRCUIT SHORT TO PASSENGER DOOR SWITCH RETURN

BODY CONTROL MODULE - PASSENGER DOOR SWITCH MUX CIRCUIT SHORTED

TEST

ACTION

APPLICABILITY

NOTE: When this code is present, the VTSS indicator will stay on solid during the
arming process.
With the DRBIII

t, record and erase DTC’s.

Cycle the ignition switch from ON to OFF to ON.
With the DRBIII

t, read DTC’s.

Lower the driver door window.
Remove the key and operate the Passenger Door Lock/Unlock Switch several times
while monitoring the DRBIII

Wait 10 seconds.
Does the DRBIII

t display PASSENGER DOOR LOCK SWITCH STUCK?

All

Yes

→ Go To 2

→ Check the switch for a binding condition and replace if necessary.

Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.

Disconnect the Passenger Door Lock Switch connector.
With the DRBIII

t in Sensors, read the PASS DOOR ENTRY voltage.

Is the voltage above 4.75 volts?

All

→ Go To 3

Yes

→ Replace the Passenger Door Lock Switch.

Perform BODY VERIFICATION TEST - VER 1.

312

POWER DOOR LOCKS/RKE

Content .. 352 353 354 355 ..