Chrysler New Yorker. Manual - part 404

TEST 3A

REPAIRING CHIME INOPERATIVE WITH EXTERIOR LAMPS ON

Perform TEST 1A Before Proceeding

C
H

I

M

E

S
Y
S

T

E

M

214

TEST 3A

REPAIRING CHIME INOPERATIVE WITH EXTERIOR LAMPS ON

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

NOTE: THE PARK PERFORM

LAMPS AND

DO THE PARK LAMPS

NO 

"EXTERIOR

START TEST 3A.

HEADLAMPS MUST BE 

AND HEADLAMPS WORK 

LIGHTING" TEST 

OPERATING

PROPERLY?

1A.

PROPERLY.

YES

DOES THE DRB

OPEN THE DRIVERS

WITH THE DRB, READ 

DISPLAY

NO 

PERFORM

DOOR.

THE DOOR AJAR 

"DRDOOR AJAR 

"DOOR AJAR"

STATUS.

SWITCH: CLOSED"? TEST 

1A.

YES

DOES THE DRB

REMOVE THE

WITH THE DRB, READ 

DISPLAY

NO 

PERFORM TEST 

IGNITION KEY. 

THE KEY-IN 

"KEY-IN IGNITION 

9A.

IGNITION STATUS.

SW: OPEN"? 

YES

TURN THE PARK 

DOES THE CHIME

NO 

REPLACE THE BODY 

LAMPS ON.

SOUND? CONTROL MODULE.* 

YES

TURN THE HEADLAMPS

DOES THE CHIME

NO 

REPLACE THE BODY 

ON.

SOUND? CONTROL MODULE.* 

YES

THE CHIME IS 

OPERATIONAL WITH 

NO TROUBLE FOUND. 

C
H

I

M

E

S
Y
S

T

E

M

215

TEST 4A

REPAIRING CHIME INOPERATIVE WITH DRIVER SEAT BELT UNFASTENED

Perform TEST 1A Before Proceeding

FIG. 1

FIG. 2

FIG. 3

C
H

I

M

E

S
Y
S

T

E

M

216

TEST 4A

REPAIRING CHIME INOPERATIVE WITH DRIVER SEAT BELT UNFASTENED

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION 
OF ALL COMPONENTS.

START TEST 4A.

TURN IGNITION OFF. 

SEE GENERAL INFO 4.0

MAKE SURE THE

DRIVER SEAT BELT 

TURN IGNITION ON 

DID THE CHIME

YES

THE CHIME IS 

IS UNFASTENED AND

(ENGINE OFF).

SOUND? 

OPERATIONAL WITH 

THE DRIVER DOOR IS 

NO TROUBLE FOUND.*

CLOSED.

NO 

DOES THE DRB

WITH THE DRB, READ 

DISPLAY

YES

REPLACE THE BODY 

THE SEAT BELT 

"SEAT BELT SWITCH:

CONTROL MODULE.* 

SWITCH STATUS.

CLOSED"? 

NO 

DISCONNECT THE

WITH A VOLTMETER, 

REPAIR SHORT TO 

SEAT BELT SWITCH 

MEASURE THE SEAT 

IS THE VOLTAGE

YES

VOLTAGE IN THE SEAT 

HARNESS

BELT SWITCH SENSE

ABOVE 5.3 VOLTS? 

BELT SW SENSE CKT. 

CONNECTOR.** CKT. 

IF 

OK, REPLACE BODY 

FIG. 1

CONTROL MODULE.* 

NO 

CONNECT A JUMPER DOES 

THE DRB

WIRE BETWEEN THE

DISPLAY

YES

REPLACE THE SEAT 

SEAT BELT SWITCH 

"SEAT BELT SWITCH:

BELT SWITCH.* 

SENSE CKT AND THE

CLOSED"? 

GROUND CKT. FIG. 1

NO 

CONNECT A JUMPER DOES 

THE DRB

WIRE BETWEEN THE

DISPLAY

YES

REPAIR THE OPEN 

SEAT BELT SWITCH 

"SEAT BELT SWITCH:

GROUND CIRCUIT.*

SENSE CKT AND

CLOSED"? 

GROUND. FIG. 1

NO 

GAIN ACCESS TO THE

CONNECT A JUMPER 

DOES THE DRB

BODY CONTROL

WIRE BETWEEN THE

DISPLAY

YES

REPAIR THE OPEN 

MODULE C4 HARNESS

SEAT BELT SWITCH 

"SEAT BELT SWITCH:

SEAT BELT SWITCH 

CONNECTOR. SENSE CKT AND

CLOSED"? SENSE CIRCUIT.*

FIG. 2

GROUND. FIG. 3

NO 

REPLACE THE BODY 
CONTROL MODULE.* 

C
H

I

M

E

S
Y
S

T

E

M

217