Chery A series. Manual - part 2

UNIT 

UNIT 

 

Electric current 

A（ampere） 

Electric power 

W（watt） 

Electric resistance 

Ω（ohm） 

Electric voltage 

V（volt） 

Length mm（millimeter） 

kPa（kilo pascal） 

Kg/cm

2

（kilogram force per square centimeter） 

Negative pressure 

Bar (bar) 

kPa（kilo pascal） 

Positive pressure 

Kg/cm

2

（kg/square centimeter） 

Torque N.m（Newton meter） 

L（liter） 

Volume 

ml（milliliter） 

g（gram） 

Weight 

Kg (kilogram) 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GI-4

FUNDAMENTAL PROCEDURES 

 
PROTECTION OF VEHICLE 
·Always be sure to cover fenders, seats and floor 
    areas before starting work.   

                                                   

 

 

 

 

 

 

 

 

PREPARATION OF TOOLS AND MEASURING EQUIPMENT 
·Be sure that all necessary tools and measuring 
    equipment are available before starting any work. 
 
 
 
 
 
 
 
DISASSEMBLY 
·If the disassembly procedure is complex, 
    requiring many parts to be disassembled ,all parts 
    should be marked in a place that will not affect   
    their performance or external appearance and   
    identified so that reassembly can be performed   
  easily and efficiently. 
 
 
 
 
INSPECTION DURING REMOVAL, DISASSEMBLY 
·When removed, each part should be carefully 
    inspected for malfunction, deformation, damage, 
  and other problems. 

 

 

 

 

 

GI-5

ARRANGEMENT OF PARTS 
·All disassembled parts should be carefully 
  arranged for reassembly. 
·Be sure to separate or otherwise identify the parts 
    to be replaced from those that will be reused. 
 
 
 
 
CLEANING OF PARTS 
·All parts to be reused should be carefully and   
    thoroughly cleaned in the appropriate method. 
 
    Warning 

·Using compressed air can cause dirt and 
    other particles to fly out causing injury to 
    the eyes. Wear protective eye wear 
    whenever using compressed air. 

 
 
REASSEMBLY 
·Standard values, such as torques and certain 
    adjustments, must be strictly observed in the 
    reassembly of all parts. 
 
 
 
 
 
·If removed, these parts should replace with new ones. 

— Oil seals 
— Gaskets 
— O-rings 
— Lockwashers 
— Cotter pins 
— Nylon nuts 

 
 
·Depending on location: 

— Sealant and gaskets, or both, should be applied to specified locations. When sealant is 

applied, parts should be installed before sealant hardens to prevent leakage. 

— Oil should be applied to the moving components of parts. 
— Specified oil or grease should be applied at the prescribed locations (such as oil seals) 

before reassembly. 

GI-6

ADJUSTMENT 
·Use suitable gauges and/or testers when making   
  adjustment.

 

 

 

 

 

 

 

 

RUBBER PARTS AND TUBING 
·Prevent gasoline or oil from getting on rubber 
  parts or tubing. 

 

 

 

 

 

 

 

HOSE CLAMPS 
·When reinstalling, position the hose clamp in the 
    original location on the hose and squeeze the clamp 
    lightly with large pliers to ensure a good fit.

 

 

 

 
 

 
 
 

VISE 
·When using a vise, put protective plates in the jaws of the vise to prevent damage to parts.

 

 

 

 

 

 

 

 

 

 

 

 

GI-7