Content .. 466 467 468 469 ..

Acura RSX Honda Integra. Manual - part 468

０１

０２

０１

Ｓ６Ｍ６Ａ００Ｈ４６２０００５３４０１ＫＢＡＴ００

Front Seat Belt

23-4

Seat Belts

Front Seat Belt Replacement

B
7/16-20 UNF
32 N·m (3.3 kgf·m,
24 lbf·ft)

B
6 x 1.0 mm
3.4 N·m (0.35 kgf·m,
2.5 lbf·ft)

C
7/16-20 UNF
32 N·m (3.3 kgf·m, 24 lbf·ft)

SRS components are located in this area. Review the
SRS component locations (see page 23-10) and the
precautions and procedures (see page 23-11) before
performing repairs or service.

NOTE: Check the front seat belts for damage, and
replace them if necessary.

1. Make sure you have the anti-theft code for the radio,

and then write down the frequencies for the preset
buttons.

2. Disconnect the negative cable from the battery, and

wait at least 3 minutes before beginning work.

3. Slide the front seat forward fully.

4. Remove the rear side trim panel (see page 20-51).

5. Remove the lower anchor cap (A), and remove the

lower anchor bolt (B).

6. Remove the upper anchor cap (A), and remove the

upper anchor bolt (B).

7. Disconnect the seat belt tensioner connector (A).

Remove the retractor mounting self-tapping ET
screw (B) and the retractor bolt (C), then remove
the front seat belt (D) and retractor (E).

8. If necessary, remove the front seat belt

protector (F).

05/06/27 18:07:54 61S6M040_230_0004

０４

０５

０６

０７

Upper anchor bolt installation

Lower anchor bolt installation

Driver’s seat

Passenger’s seat with BOSE sound system

Seat Belt Buckle

23-5

COLLARS

UPPER ANCHOR

UPPER ANCHOR BOLT

BUSHING

TOOTHED LOCK WASHER

WASHER

SPRING WASHER

COLLAR

WASHER

COLLAR

LOWER ANCHOR BOLT

BUSHING

LOWER ANCHOR

SPRING WASHER

TOOTHED LOCK WASHER

WAVE WASHER

9. Install the belt in the reverse order of removal, and

note these items:

• If the threads on the retractor mounting

self-tapping ET screw are worn out, use an
oversized self-tapping ET screw (P/N 90133-
SZ4-003) made specifically for this application.

• Apply liquid thread lock to the anchor bolts

before reinstallation.

• Check that the retractor locking mechanism

functions (see page 23-8).

• Assemble the washers, collars, and bushings on

the upper and lower anchor bolts as shown.

• If the seat belt tensioner has been activated,

replace the front seat belt protector with a new
one.

• Before installing the anchor bolts, make sure

there are no twists or kinks in the seat belt.

• Make sure the seat belt tensioner connector is

plugged in properly.

• Reconnect the negative cable to the battery.
• Enter the anti-theft code for the radio, and then

enter the customer’s radio station presets.

• Reset the clock.
• ’02-04 models; Do the ECM/PCM idle learn

procedure (see page 11-349).

• Do the power window control unit reset

procedure (see page 22-148).

1. Make sure you have the anti-theft code for the radio,

and then write down the frequencies for the preset
buttons.

2. Disconnect the negative cable from the battery, and

wait at least 3 minutes before beginning work.

3. Remove the front seat (see page 20-75).

4. On the passenger’s seat with BOSE sound system,

remove the front stereo amplifier (see page 22-122).

5. Detach the seat belt switch connector clip (A) and

seat belt buckle tensioner connector clip (B), and on
the passenger’s seat with BOSE sound system,
disconnect the subharness connector (C) from the
seat belt switch connector. Remove the harness
band (D) from the seat cushion frame spring (E).
The driver’s seat and passenger’s seat with BOSE
sound system are shown, the passenger’s seat
without BOSE sound system is similar to the driver’s
seat.

(cont’d)

05/06/27 18:07:54 61S6M040_230_0005

０１

０２

Ｓ６Ｍ６Ａ００Ｈ４６２０００５３４０２ＫＢＡＴ００

Rear Seat Belt

23-6

Seat Belts

Front Seat Belt Replacement
(cont’d)

Rear Seat Belt Replacement

A
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)

A
7/16-20 UNF
32 N·m (3.3 kgf·m,
24 lbf·ft)

B
7/16-20 UNF
32 N·m (3.3 kgf·m, 24 lbf·ft)

6. Remove the center anchor bolt (A), and remove the

seat belt buckle (B).

NOTE: The passenger’s seat is shown; the driver’s
seat is similar.

7. Pull the seat belt switch/tensioner harness (C) out

through the hole in the seat track, and remove the
seat belt buckle from the retainer band (D)
(passenger’s seat).

8. Install the buckle in the reverse order of removal,

and note these items:

• Apply liquid thread lock to the center anchor bolt

before reinstallation.

• Apply liquid thread lock to the seat mounting

bolts before reinstallation.

• Reconnect the negative cable to the battery.
• Enter the anti-theft code for the radio, and then

enter the customer’s radio station presets.

• Reset the clock.
• ’02-04 models; Do the ECM/PCM idle learn

procedure (see page 11-349).

• Do the power window control unit reset

procedure (see page 22-148).

NOTE: Check the rear seat belts for damage, and
replace them if necessary.

1. Remove the rear side trim panel (see page 20-51).

2. Remove the lower anchor bolt (A).

3. Remove the upper anchor cap (A), and remove the

upper anchor bolt (B).

05/06/27 18:07:55 61S6M040_230_0006

０１

０４

０５

Upper anchor bolt installation

Seat Belt Buckles

23-7

A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)

B
7/16-20 UNF
32 N·m
(3.3 kgf·m,
24 lbf·ft)

COLLAR

UPPER ANCHOR

UPPER ANCHOR BOLT

BUSHING

TOOTHED LOCK WASHER

WASHER

SPRING WASHER

COLLARS

A
7/16-20 UNF
32 N·m (3.3 kgf·m, 24 lbf·ft)

4. Remove the quarter pillar trim as necessary

(see page 20-52).

5. Remove the retractor mounting bolt (A) and the

retractor bolt (B), then remove the rear seat belt (C)
and retractor (D).

6. Install the belt in the reverse order of removal, and

note these items:

• Apply liquid thread lock to the anchor bolts

before reinstallation.

• Check that the retractor locking mechanism

functions as described (see page 23-8).

• Assemble the washers, collars, and bushing on

the upper anchor bolt as shown.

• Before installing the anchor bolt, make sure there

are no twists or kinks in the seat belt.

1. Remove the rear seat cushion (see page 20-85).

2. Remove the center anchor bolts (A), and remove

the seat belt buckles (B).

3. Install the buckles in the reverse order of removal,

and apply liquid thread lock to the anchor bolts
before reinstallation.

05/06/27 18:07:55 61S6M040_230_0007

Content .. 466 467 468 469 ..