FANUC Series 30i/300i/300is-MODEL A. Machining Center System. User's manual - page 281

A.PARAMETERS

 APPENDIX 

B-63944EN/03

 

 

- 2204 - 

12313 

 

States of the manual handle feed axis selection signals when the first 

rotation axis is turned in tool tip center rotation handle feed/interrupt 

 

 

[Input type]  Parameter input 

 

[Data type]  Byte path 

  [Valid data range]  1 to 24 

This parameter sets the states of the manual handle feed axis selection 
signals (HS1A to HS1E for the first manual handle) or the manual 
handle interrupt axis selection signals (HS1IA to HS1IE for the first 
manual handle) when the first rotation axis is turned in tool tip center 
rotation handle feed or interrupt. (For settings, see "Table of 
correspondence with the manual handle feed axis selection signals" in 
the description of parameter No. 12310.) 
The handle for which the signal states are set is determined by 
parameter No. 12323. 
 

12314 

 

States of the manual handle feed axis selection signals when the second 

rotation axis is turned in tool tip center rotation handle feed/interrupt 

 

 

[Input type]  Parameter input 

 

[Data type]  Byte path 

  [Valid data range]  1 to 24 

This parameter sets the states of the manual handle feed axis selection 
signals (HS1A to HS1E for the first manual handle) or the manual 
handle interrupt axis selection signals (HS1IA to HS1IE for the first 
manual handle) when the second rotation axis is turned in tool tip 
center rotation handle feed or interrupt. (For settings, see "Table of 
correspondence with the manual handle feed axis selection signals" in 
the description of parameter No. 12310.) 
The handle for which the signal states are set is determined by 
parameter No. 12323. 
 

12318 

 

Tool length in three-dimensional machining manual feed 

 

 

[Input type]  Setting input 

 

[Data type]  Real path 

 

[Unit of data]  mm, inch (machine unit) 

 

[Minimum unit of data]  Depend on the increment system of the reference axis 

 [Valid data range]  9 digit of minimum unit of data (refer to standard parameter setting 

table (A)) 
(When the increment system is IS-B, -999999.999 to +999999.999) 
This parameter sets a tool length when tool tip center rotation feed is 
performed with the three-dimensional machining manual feed function 
and when the three-dimensional machining manual feed screen is 
displayed. 
 

NOTE 

 

Specify a radius value to set this parameter. 

 

B-63944EN/03

 APPENDIX 

A.PARAMETERS

 

 

- 2205 - 

  

#7 #6 #5 #4 #3 #2 #1 #0 

12320 

 

     

JFR 

FLL 

TWD 

 

 

[Input type]  Parameter input 

 

[Data type]  Bit path 

 

        # 0 

TWD

  The directions of three-dimensional machining manual feed (other 

than tool tip center rotation feed) when the tilted working plane 
command is issued are: 
0:  Same as those not in the tilted working plane command. That is, 

the directions are: 

 

Tool axis normal direction 1 (table-based horizontal direction 1) 

 

Tool axis normal direction 2 (table-based horizontal direction 2) 

 

Tool axis direction (table-based vertical direction) 

1:  X, Y, and Z directions in the feature coordinate system. 

 

        # 1 

FLL

  The directions of tool axis normal direction feed or table-based 

horizontal direction feed in the three-dimensional machining manual 
feed mode are: 
0:  Tool axis normal direction 1 (table-based horizontal direction 1) and 

tool axis normal direction 2 (table-based horizontal direction 2). 

1:  Longitude direction and latitude direction. 

 

Parameter FLL 

(No.12320#1) 

Parameter TWD

(No.12320#0) 

Directions of three-dimensional machining manual feed 

0 0 

Conventional 

directions 

0 1 

When the tilted working plane command is issued: X, Y, and Z 
directions in the feature coordinate system 
When the command is not issued: Conventional directions 

1 

0 

Longitude direction and latitude direction 

1 1 

When the tilted working plane command is issued: X, Y, and Z 
directions in the feature coordinate system 
When the command is not issued: Longitude direction and 
latitude direction 

 

    # 2 

JFR

  As the feeedrate of three-dimensional machining manual feed (jog 

feed or incremental feed) : 
0:  The dry run rate (parameter No. 1410) is used. 
1:  The jog feedrate (parameter No. 1423) is used. 
 

12321 

 

Normal axis direction 

 

 

[Input type]  Parameter input 

 

[Data type]  Byte path 

  [Valid data range]  0 to 3 

When a tilted working plane command (G68.3) is issued to perform 
three-dimensional machining manual feed in the latitude direction, 
longitude direction, and tool axis direction, this parameter sets an axis 
parallel to the normal direction. 
1 : Positive (+) X-axis direction 
2 : Positive (+) Y-axis direction 
3 : Positive (+) Z-axis direction 
0 : Reference tool axis direction (parameter No. 19697) 

A.PARAMETERS

 APPENDIX 

B-63944EN/03

 

 

- 2206 - 

 

12322 

 

Angle used to determine whether to assume the tool axis direction to be 

parallel to the normal direction (parameter No. 12321) 

 

 

[Input type]  Parameter input 

 

[Data type]  Real path 

 

[Unit of data]  deg 

 

[Minimum unit of data]  Depend on the increment system of the reference axis 

  [Valid data range]  0 to 90 

When a tilted working plane command (G68.3) is issued to perform 
three-dimensional machining manual feed in the latitude direction, 
longitude direction, and tool axis direction, if the angle between the 
tool axis direction and normal direction (parameter No. 12321) is too 
small, the tool axis direction is assumed to be parallel to the normal 
direction (parameter No. 12321). This parameter sets the maximum 
angle at which the tool axis direction is assumed to be parallel to the 
normal direction. 
When this parameter is set to 0 or a value outside the valid range, it is 
set to 1 degree. 
 

12323 

 

Number of a manual handle used for three-dimensional machining manual 

feed 

 

 

[Input type]  Setting input 

 

[Data type]  Byte path 

  [Valid data range]  0 to 5 

When three-dimensional machining manual feed (handle feed) is 
performed, set the number of the manual handle to be used. 
When the second or third manual handle is used for three-dimensional 
machining manual feed, the option for manual handle feed with 2/3 
handles is required. 
When the fourth or fifth manual handle is used for three-dimensional 
machining manual feed, the option for manual handle feed with 4/5 
handles is required. 
If 0 or the number of an unavailable handle is set, the first handle is 
assumed. 
 

12600 

 

Identification Number for synchronous, composite and superimposed 

control with program command 

 

 

[Input type]  Parameter input 

 

[Data type]  Word axis 

  [Valid data range]  0,1 to 32767 

Set identification numbers that can be specified with P,Q addresses. 
The axis whose identification number is "0" cannot become under 
synchronous /composite /superimposed control by CNC program. 
The same identification number cannot be set to two or more axes 
through all paths. 
When the same identification number is set, PS alarm (PS5339) occurs 
at G50.4/G50.5/G50.6/G51.4/G51.5/G51.6 block. 
 

B-63944EN/03

 APPENDIX 

A.PARAMETERS

 

 

- 2207 - 

  

#7 #6 #5 #4 #3 #2 #1 #0 

13113 

 

    

CFD 

  

CLR 

 

 

[Input type]  Parameter input 

 

[Data type]  Bit path 

 

        # 0 

CLR

  Upon reset, the display of a travel distance by three-dimensional 

machining manual feed is: 
0: Not 

cleared. 

1: Cleared. 
 

        # 3 

CFD

  As feedrate F, the three-dimensional machining manual feed screen 

displays: 
0:  Composite feedrate at the linear axis/rotation axis control point. 
1:  Feedrate at the tool tip. 
 

  

#7 #6 #5 #4 #3 #2 #1 #0 

13200 

 

    

ETE 

TRT 

  

 

 

[Input type]  Parameter input 

 

[Data type]  Bit path 

 

        # 2 

TRT

  As the remaining lifetime value for outputting the tool life arrival 

notice signal: 
0:  The remaining lifetime of the last tool is used. 
1:  The sum of the remaining lifetimes of the tools with the same 

type number is used. 

 

NOTE 

 

This parameter is valid when bit 3 (ETE) of 
parameter No. 13200 is set to 0 (arrival notice for 
each type number). 

 

        # 3 

ETE

  The tool life arrival notice signal is output: 

0:  For each tool type. 
1:  For each tool. 
 

A.PARAMETERS

 APPENDIX 

B-63944EN/03

 

 

- 2208 - 

  

#7 #6 #5 #4 #3 #2 #1 #0 

13201 

 

      

TDN 

TDC 

 

 

[Input type]  Parameter input 

 [Data 

type] 

Bit 
 

NOTE 

 

When at least one of these parameters is set, the 
power must be turned off before operation is 
continued. 

 

        # 0 

TDC

  The function of customizing the tool management data screen of the 

tool management function is: 
0: Disabled. 
1: Enabled. 
 

        # 1 

TDN

  On the tool management function screen, the character string for 

indicating the tool life status can contain: 
0:  Up to 6 characters. 
1:  Up to 12 characters. 
 

  

#7 #6 #5 #4 #3 #2 #1 #0 

13202  DOM

DOT 

 

DO2  DOB  DOY  DCR 

 

 

 

[Input type]  Parameter input 

 [Data 

type] 

Bit 
 

        # 1 

DCR

  On the tool management function screen, tool nose radius 

compensation data is: 
0: Displayed. 
1: Not 

displayed. 

 

NOTE 

 

This parameter is valid when the machine control 
type is the lathe system or compound system. 

 

        # 2 

DOY

  On the tool management function screen, Y-axis offset data is: 

0: Displayed. 
1: Not 

displayed. 

 

NOTE 

 

This parameter is valid when the machine control 
type is the lathe system or compound system. 

 

B-63944EN/03

 APPENDIX 

A.PARAMETERS

 

 

- 2209 - 

        # 3 

DOB

  On the tool management function screen, B-axis offset data is: 

0: Displayed. 
1: Not 

displayed. 

 

NOTE 

 

This parameter is valid when the machine control 
type is the lathe system or compound system. 

 

        # 4 

DO2

  On the tool management function screen, the second geometry tool 

offset data is: 
0: Displayed. 
1: Not 

displayed. 

 

NOTE 

 

This parameter is valid when the machine control 
type is the lathe system or compound system. 

 

        # 6 

DOT

  On the tool management function screen, the tool offset data (X, Z) of 

the T series is: 
0: Displayed. 
1: Not 

displayed. 

 

NOTE 

 

This parameter is valid when the machine control 
type is the lathe system or compound system. 

 

        # 7 

DOM

  On the tool management function screen, the tool offset data of the M 

series is: 
0: Displayed. 
1: Not 

displayed. 

 

NOTE 

 

This parameter is valid when the machine control 
type is the machining center system or compound 
system. 

 

  

#7 #6 #5 #4 #3 #2 #1 #0 

13204 

 

       

TDL 

 

 

[Input type]  Parameter input 

 [Data 

type] 

Bit 
 

        # 0 

TDL

  The protection function for tool management data using a key is: 

0: Disabled. 
1: Enabled. 
 

A.PARAMETERS

 APPENDIX 

B-63944EN/03

 

 

- 2210 - 

13220 

 

Number of valid tools in tool management data 

 

NOTE 

 

When this parameter is set, the power must be 
turned off before operation is continued. 

 

 

[Input type]  Parameter input 

 [Data 

type] 

Word 

  [Valid data range]  0 to 64 (Extended to 240 or 1000 by the addition of an option) 

This parameter sets the number of valid tools in tool management 
data. 
 

13221 

 

M code for tool life count restart 

 

 

[Input type]  Parameter input 

 

[Data type]  Word path 

  [Valid data range]  0 to 65535 

When 0 is set in this parameter, this parameter is ignored. 
When an M code for tool life count restart is specified, the counting of 
the life of the tool attached at the spindle position is started. When the 
type for counting the number of use times is selected, the target of life 
counting is switched to the tool attached at the spindle position, and 
the life count is incremented by 1. 
When the type for counting time is selected, the target of life counting 
is switched to the tool attached at the spindle position but no other 
operations are performed. If the tool attached at the spindle position is 
not a tool under tool life management, no operation is performed. 
The M code set in parameter No. 6811 waits for FIN. However, the M 
code set in this parameter does not wait for FIN. 
The M code set in parameter No. 13221 must not be specified in a 
block where another auxiliary function is specified. 
The M code set in parameter No. 13221 does not wait for FIN. So, do 
not use the M code for other purposes. 
 

NOTE 

 

The use of this parameter varies depending on 
whether it is used by the tool management function 
or tool life management function. 

 

13222 

 

Number of data items in the first cartridge 

 

NOTE 

 

When this parameter is set, the power must be 
turned off before operation is continued. 

 

 

[Input type]  Parameter input 

 [Data 

type] 

Word 

  [Valid data range]  1 to 64 (Extended to 240 or 1000 by the addition of an option) 

This parameter sets the number of data items used with the first 
cartridge. 

B-63944EN/03

 APPENDIX 

A.PARAMETERS

 

 

- 2211 - 

 

13223 

 

Start pot number of the first cartridge 

 

NOTE 

 

When this parameter is set, the power must be 
turned off before operation is continued. 

 

 

[Input type]  Parameter input 

 [Data 

type] 

Word 

  [Valid data range]  1 to 9999 

This parameter sets the start pot number to be used with the first 
cartridge. Pot numbers starting with the value set in this parameter and 
sequentially incremented by 1 are assigned to all data items. 
 

13227 

 

Number of data items in the second cartridge 

 

NOTE 

 

When this parameter is set, the power must be 
turned off before operation is continued. 

 

 

[Input type]  Parameter input 

 [Data 

type] 

Word 

  [Valid data range]  1 to 64(Extended to 240 or 1000 by the addition of an option) 

This parameter sets the number of data items used with the second 
cartridge. 
 

13228 

 

Start pot number of the second cartridge 

 

NOTE 

 

When this parameter is set, the power must be 
turned off before operation is continued. 

 

 

[Input type]  Parameter input 

 [Data 

type] 

Word 

  [Valid data range]  1 to 9999 

This parameter sets the start pot number to be used with the second 
cartridge. Pot numbers starting with the value set in this parameter and 
sequentially incremented by 1 are assigned to all data items. 
 

13232 

 

Number of data items in the third cartridge 

 

NOTE 

 

When this parameter is set, the power must be 
turned off before operation is continued. 

 

 

[Input type]  Parameter input 

 [Data 

type] 

Word 

  [Valid data range]  1 to 64(Extended to 240 or 1000 by the addition of an option) 

This parameter sets the number of data items used with the third 
cartridge.