Content      ..     9      10      11      12     ..

Vauxhall Movano (2016 year). Manual - part 11

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

175

It is advisable to carry a full set of

fuses. Consult a workshop.

Some functions are protected by

several fuses.

Fuses may also be inserted without

existence of a function.

Notice

Not all fuse box descriptions in this

manual may apply to your vehicle.

When inspecting the fuse box, refer

to the fuse box label.

Fuse extractor

A blown fuse can be recognised by its

To help in replacing fuses, a fuse

melted wire. Do not replace the fuse

extractor is located in the instrument

until the cause of the fault has been

panel fuse box.

remedied.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

176

Vehicle care

Place the fuse extractor on the

Symbol Circuit

Symbol Circuit

various types of fuse from the top or

side, and withdraw fuse.

n Heating and ventilation

Z

Infotainment system / Seat

system / Air conditioning

heating / Vehicle display

screen / Audio connec-

Engine compartment fuse

V Heated windscreen

tions / Alarm

box

?

Power outlet

Located below the coolant expansion

Instrument panel fuse box

tank.

Ì

Cigarette lighter

Some circuits may be protected by

e

Instrument panel

several fuses.

U

Central locking

Due to restricted accessibility, have

fuses replaced by a workshop.

0

Interior lights

Symbol Circuit

O

Turn signals / Rear fog

lights / Body control module

S

Right side lights

DIAG

Diagnostic connector

T

Left side lights

u

ABS / Electronic Stability

W

Right low beam

Program

a

Left low beam

Located behind the trim panel on the

d

Interior lights / Brake lights

>

Front fog light

left-hand side of the instrument panel.

Z

Body control module

Pull upper part of trim panel to

L

Left high beam

remove.

STOP

Brake light

N

Right high beam

Do not store any objects behind this

panel.

u

ABS

Some circuits may be protected by

K

Windscreen wiper

several fuses.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

177

Symbol Circuit

Symbol Circuit

Using a suitable tool, e.g. a flat-blade

screwdriver, unclip the trim panel at

I

Body control module /

Q

Pneumatic suspension

the 3 locations shown in the

Power windows / Heating

illustration and remove.

O Navigation system

and ventilation system / Air

Do not store any objects behind this

conditioning

ADP Additional adaptations

panel.

m

Left heated rear window

, Power windows / Body

control module

n

Right heated rear window

R

Windscreen washer

Load compartment fuse box

M

Electronic immobiliser

Combi

U

Heated seats

FBL

Cornering light

l

Hands-free connection

&

Tachograph

PTO

Power take-off

No. Circuit

j

Horn

1

Speed 3: additional evaporator

Í

Preheating / Diesel fuel filter

2

Speed 2: additional evaporator

x

Climate control fan

3

Speed 1: additional evaporator

d

Heated exterior mirrors

Located behind the trim panel on the

T

Left-hand side light

right-hand side of the load

compartment, beside the rear door.

S

Right-hand side light

-------------------------------------------------------------------------------------------------------------------------------------------------------------

178

Vehicle care

Bus

No. Circuit

1

Speed 2: right-hand evaporator

fan

2

Speed 2: left-hand evaporator

fan

3

Speed 1: left-hand evaporator

fan

4

Left-hand heating

5

Speed 3: left-hand evaporator

fan

6

Condenser fan

Located below the step trim panel on

the lower right-hand side of the load

7

Right-hand heating

compartment.

8

Speed 3: right-hand evaporator

Using a suitable tool, e.g. a flat-blade

fan

screwdriver, unclip the trim panel at

the 3 locations shown in the

9

Power sliding door

illustration and remove.

10

Corridor lighting

Do not store any objects behind this

panel.

11

Foot panel

12

Child safety warning buzzer

13

Speed 1: right-hand evaporator

fan

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

179

Some circuits may be protected by

Vehicle tools

several fuses.

Tools

Vehicles with Rear-wheel drive: A

hydraulic jack and a set of extension

pieces for use with the jack are also

included.

The jack, wheel wrench, adapters (for

spare wheel removal), hub cap hook

and towing eye are contained in a

unit, stowed under the front seat.

Notice

Depending on vehicle, there may be

multiple adapters for spare wheel

removal.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------------------------------------

182

Vehicle care

10 °C temperature increase. This

Notice

A detected low tyre pressure

must be considered when warm tyres

In countries where the tyre pressure

condition is indicated by illumination

are checked.

monitoring system is legally

of control indicator w 3 89 and a

required, the use of wheels without

corresponding message appears in

Rear-wheel drive, with twin rear

pressure sensors will invalidate the

the DIC.

wheels

vehicle type approval.

If w illuminates, stop as soon as

When inflating the outer tyre, the

The TPMS sensors monitor the air

possible and inflate the tyres as

inflation tube should be passed

pressure in the tyres and transmit tyre

recommended 3 225.

between the two wheels.

pressure readings to a receiver

After inflating, some driving may be

located in the vehicle.

required to update the tyre pressure

Tyre pressure monitoring

Tyre pressure chart 3 225.

values in the system. During this time

w may illuminate.

system

Low tyre pressure condition

If w illuminates at lower temperatures

The Tyre Pressure Monitoring

and extinguishes after some driving,

System (TPMS) uses radio and

this could be an indicator for

sensor technology to check tyre

approaching a low tyre pressure

pressure levels.

condition. Check tyre pressure of all

four tyres.

Caution

If the tyre pressure must be reduced

or increased, switch off ignition.

Tyre pressure monitoring system

warns only about low tyre pressure

Only mount wheels with pressure

condition and does not replace

sensors, otherwise w flashes for

regular tyre maintenance by the

several seconds then illuminates

driver.

continuously together with control

indicator A 3 87 and a

All wheels must be equipped with

corresponding message appears in

pressure sensors and the tyres must

the DIC.

have the prescribed pressure.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

183

A spare wheel or temporary spare

Relearn function

Several minutes of driving at a speed

wheel is not equipped with pressure

above 25 mph may be required to

sensors. TPMS is not operational for

complete the relearn process. The

these wheels. For the further three

system can only provide limited

wheels, TPMS remains operational.

information during this time.

Control indicator w and the

If problems occur during the relearn

corresponding message appears at

process, control indicator w remains

each ignition cycle until the tyres are

illuminated and a warning message is

inflated to the correct tyre pressure.

displayed in the DIC.

Driver Information Centre (DIC) 3 92.

Driver Information Centre (DIC) 3 92.

Vehicle messages 3 92.

Vehicle messages 3 92.

Puncture

General information

A puncture or severely under-inflated

After a puncture has been repaired

The use of tyre chains or

tyre is indicated by illumination of

and the driver has inflated the tyres to

commercially available liquid tyre

control indicator w together with C

the correct tyre pressure, TPMS

repair kits can impair the function of

3 88 and a corresponding message

needs to recalculate.

the system. Factory-approved tyre

appears in the DIC. Stop vehicle and

Tyre pressure 3 225, Tyre repair kit

repair kits can be used.

switch off engine.

3 185.

Tyre repair kit 3 185, Tyre chains

Tyre pressure 3 225, Tyre repair kit

During driving, select the tyre

3 185.

3 185, Spare wheel 3 190, Wheel

pressure menu in the DIC by pressing

External high-power radio equipment

changing 3 188.

button on end of wiper lever. Press

could disrupt the tyre pressure

and hold button for approx.

monitoring system.

5 seconds to initialise recalculation. A

Each time the tyres are replaced,

corresponding message appears in

TPMS sensors must be dismounted

the DIC.

and serviced by a workshop.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

184

Vehicle care

indicators (TWI). Their position is

Tread depth

Wheel covers

indicated by markings on the

Check tread depth at regular

Wheel covers and tyres that are

sidewall.

intervals.

factory approved for the respective

Tyres age, even if they are not used.

vehicle and comply with all of the

Tyres should be replaced for safety

We recommend tyre replacement

relevant wheel and tyre combination

reasons at a tread depth of 2-3 mm

every 6 years.

requirements must be used.

(4 mm for winter tyres).

If the wheel covers and tyres used are

For safety reasons it is recommended

Changing tyre and wheel

not factory approved, the tyres must

that the tread depth of the tyres on

one axle should not vary by more than

size

not have a rim protection ridge.

2 mm.

If tyres of a different size than those

Wheel covers must not impair brake

fitted at the factory are used, it may be

cooling.

necessary to reprogramme the

speedometer as well as the nominal

9 Warning

tyre pressure and make other vehicle

modifications.

Use of unsuitable tyres or wheel

covers could lead to sudden

After converting to a different tyre

pressure loss and thereby

size, have the label with tyre

accidents.

pressures replaced.

9 Warning

Use of unsuitable tyres or wheels

may lead to accidents and will

The legally permissible minimum

invalidate the vehicle type

tread depth (1.6 mm) has been

approval.

reached when the tread has worn

down as far as one of the tread wear

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

185

Wheel covers on steel wheels may

Tyre chains

9 Warning

come into contact with parts of the

chains. In such cases, remove the

Do not drive faster than 50 mph.

wheel covers.

Do not use for a lengthy period.

Tyre chains may only be used at

speeds up to 30 mph and, when

Steering and handling may be

travelling on roads that are free of

affected.

snow, they may only be used for brief

periods since they are subject to rapid

If the vehicle has a flat tyre:

wear on a hard road and may snap.

Apply the parking brake and engage

The use of tyre chains is not permitted

neutral (manual transmission) or N

on the temporary spare wheel.

(manual transmission automated).

The tyre repair kit is located under the

Tyre repair kit

front seat. Slide seat forwards fully

Tyre chains are only permitted on the

and fold backrest down to access kit.

drive wheels.

Minor damage to the tyre tread can be

repaired with the tyre repair kit.

1. Take the tyre repair kit out from

On vehicles with twin rear wheels,

under the front seat.

tyre chains are only permitted on the

Do not remove foreign bodies from

outer wheels.

the tyres.

2. Remove the compressor.

Always use fine mesh chains that add

Tyre damage exceeding 4 mm or that

3. Remove the power supply lead(s)

no more than 15 mm to the tyre tread

is at the tyre's sidewall near the rim

and air hose from the stowage

and the inboard sides (including chain

cannot be repaired with the tyre repair

compartments on the underside

lock).

kit.

of the compressor.

9 Warning

Damage may lead to tyre blowout.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

186

Vehicle care

9. Connect the red < power supply

lead on the compressor to the

jump start terminal 3 193.

Notice

Depending on model, the jump start

terminal may be located at the left-

hand or right-hand side of the engine

compartment.

4. Screw the compressor air hose to

7. Screw the sealant filler hose to the

the connection on the sealant

tyre valve.

bottle.

8. The rocker switch on the

5. Fit the sealant bottle into the

compressor must be set to

retainer on the compressor.

position O.

Set the compressor near the tyre

in such a way that the sealant

bottle is upright.

6. Unscrew valve cap from defective

10. Connect the black ] power

tyre.

supply lead to a vehicle grounding

point, e.g. the engine block or an

engine mounting bolt.

Notice

Depending on tyre repair kit type, it

may be necessary to connect the

single power supply lead to the

-------------------------------------------------------------------------------------------------------------------------------------------------------------

187

Vehicle care

power outlet or cigarette lighter

damaged. Seek the assistance of

socket.

a workshop.

For this type, the red < and

Drain excess tyre pressure with

black ] power supply leads will not

the button beside the pressure

be present.

indicator.

To avoid discharging the battery,

Do not run the compressor for

we recommend running the

longer than 10 minutes.

engine.

15. Detach the tyre repair kit.

16. Remove any excess sealant

using a cloth.

17. Take the label indicating

14. The prescribed tyre pressure

maximum permitted speed from

should be obtained within

the tyre repair kit and affix in the

10 minutes. Tyre pressure

driver's field of view.

3 225. When the correct pressure

18. Screw the sealant filler hose to the

is obtained, turn off the

free connection on the sealant

compressor by setting rocker

bottle. This prevents sealant from

switch to position O.

escaping. Store the sealant bottle

If the prescribed tyre pressure is

in the plastic bag. Stow tyre repair

not obtained within 10 minutes,

kit under the front seat.

11. Set the rocker switch on the

remove the tyre repair kit. Move

compressor to position I. The tyre

the vehicle one tyre rotation

is filled with sealant.

(approx. 2 metres). Reattach the

12. The compressor pressure gauge

tyre repair kit and continue the

briefly indicates up to 6 bar. Then

filling procedure for 10 minutes. If

the pressure starts to drop.

the prescribed tyre pressure is still

not obtained, the tyre is too badly

13. All of the sealant is pumped into

the tyre. Then the tyre is inflated.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

188

Vehicle care

not be driven. Seek the

Wheel changing

assistance of a workshop.

Some vehicles are equipped with a

21. Stow tyre repair kit under the front

tyre repair kit instead of a spare wheel

seat.

3 185.

Notice

Make the following preparations and

The driving characteristics of the

observe the following information:

repaired tyre are severely affected,

●

Park the vehicle on a level, firm

therefore have this tyre replaced.

and non-slippery surface. The

If unusual noise is heard or the

front wheels must be in the

compressor becomes hot, turn

straight-ahead position.

compressor off for at least

●

Apply the parking brake and

30 minutes.

19. Continue driving immediately so

engage first gear or reverse gear

that the sealant is evenly

The built-in safety valve opens at a

(manual transmission) or N

distributed throughout the tyre.

pressure of 7 bar (102 psi).

(manual transmission

After driving approx. 6 miles, but

Note the expiry date of the kit. After

automated).

no more than 10 minutes, stop

this date its sealing capability is no

●

Switch off the air suspension

and check tyre pressure using the

longer guaranteed. Pay attention to

system 3 125.

compressor. Screw compressor

storage information on sealant

●

Remove the spare wheel 3 190.

air hose directly onto tyre valve

bottle.

and compressor when doing this.

●

Never change more than one

Replace the used sealant bottle.

wheel at a time.

20. If the tyre pressure is more than

Dispose of the bottle as prescribed

3.1 bar, set it to the correct value.

by applicable laws.

●

Use the jack only to change

Repeat the procedure until there

wheels in case of puncture, not

The compressor and sealant can be

is no more loss of pressure.

for seasonal winter or summer

used from approx. -30 °C.

tyre change.

If the tyre pressure has fallen

below 3.1 bar, the vehicle must

●

The jack is maintenance-free.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

189

● If the ground on which the vehicle

Ensure the jack is positioned

is standing is soft, a solid board

correctly. The jack base must be

(max. 1 cm thick) should be

on the ground directly below the

placed under the jack.

jacking hole in a manner that

prevents it from slipping.

● No people or animals may be in

the vehicle when it is jacked-up.

Attach wheel wrench onto the jack

and raise the vehicle by turning

● Never crawl under a jacked-up

the wrench until the wheel is clear

vehicle.

of the ground.

● Do not start the engine when the

vehicle is raised on the jack.

● Clean wheel bolts/nuts and their

threads before mounting the

wheel.

9 Warning

Do not grease wheel bolt, wheel

nut and wheel nut cone.

1. Remove the wheel cover using

the hook supplied. Vehicle tools

Vehicles with Rear-wheel drive:

3 179.

Pay attention to the operating

2. Install the wheel wrench ensuring

instructions supplied with the

that it locates securely and loosen

3. Vehicles with Front-wheel drive:

hydraulic jack and assemble the

each wheel bolt/nut by half a turn.

parts required as specified.

Raise vehicle by placing lifting

pad spigot of the jack under the

Position the adapter at the jacking

jacking hole located nearest the

hole located nearest the wheel

wheel concerned.

concerned.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

191

To release the spare wheel, loosen

Place wheel upright, unclip retainer

When reinstalling a spare wheel, first

cable by connecting the wheel

from wheel rim and release the wheel

attach the mounting plate (twin rear

wrench and adapters (depending on

from the cable and connected

wheel vehicles) and secure with the

vehicle) to the slot position illustrated

retainer by routing these components

nut.

and lower the wheel fully by turning

through the centre of the wheel.

Place wheel upright, then route the

wrench clockwise.

Twin rear wheel vehicles have an

cable and connected retainer from

additional mounting plate attached to

the front of the wheel (side with tyre

Caution

the spare wheel. Before using the

valve) and through the centre of the

wheel, undo the nut and remove the

wheel. Attach the retainer and clip it

Only use the wheel wrench and

mounting plate.

into place, ensuring it is correctly

adapters (depending on vehicle)

positioned and that the front of the

to lower the spare wheel.

wheel (side with tyre valve) will be

The use of pneumatic tools is

facing upwards when reinstalled.

prohibited. This may result in

damage to the winch cable and

equipment.

Content      ..     9      10      11      12     ..