Vauxhall Mokka X (2016 year). Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Seats, restraints

ISOFIX child restraint

Installation of ISOFIX child

restraint systems with permanent

systems

guide

Installation of ISOFIX child

restraint systems without

permanent guide

ISOFIX mounting brackets are

indicated by a label on the backrest.

The vehicle might be equipped with

guides in front of the mounting

brackets to support the installation of

the child restraint system.

Fasten vehicle-approved ISOFIX

child restraint systems to the ISOFIX

mounting brackets. Specific vehicle

ISOFIX child restraint system

positions are marked in the table by

IL.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Seats, restraints

The covers of the guides will swivel

For non-ISOFIX child restraints,

backwards automatically when

fasten the Top-Tether strap to the

attaching the child restraint system.

Top-Tether fastening eyes. The strap

must run between the two guide rods

of the head restraint.

Top-tether fastening eyes

For ISOFIX child restraints, fasten the

Depending on country specific

Top-Tether strap to the Top-Tether

equipment, the vehicle might have

fastening eyes in addition to the

two or three fastening eyes.

ISOFIX mounting. The strap must run

Top-Tether fastening eyes are

between the two guide rods of the

marked with the symbol : for a child

head restraint.

restraint.

ISOFIX child restraint systems of

universal category positions are

marked in the table by IUF.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

To open, pull the handle.

Storage

Storage compartments

The glovebox should be closed while

driving.

9 Warning

Storage compartments

Cupholders

Glovebox

Do not store heavy or sharp

Cupholders

objects in the storage

Front storage

compartments. Otherwise, the

Sunglasses storage

storage compartment lid could

Underseat storage

open and vehicle occupants could

Centre console storage

be injured by objects being thrown

Rear carrier system

around in the event of hard

braking, a sudden change in

Load compartment

direction or an accident.

Load compartment cover

Rear floor storage cover

Lashing eyes

Glovebox

Warning triangle

First aid kit

Roof rack system

The cupholders are located in the

Roof rack

centre console and rear part of the

Loading information

centre console.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

A storage compartment is located

Sunglasses storage

next to the steering wheel. Pull the

handle to open.

To use the rear seat cupholder, pull

the strap in the rear seat armrest.

Fold down and open.

Do not use for storing heavy objects.

Front storage

A further storage compartment is

located in the centre console.

To open, press the button.

The covers of the storage

compartments should be closed while

driving.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

Underseat storage

Centre console storage

Rear carrier system

Rear carrier system for three

bicycles

Lift drawer at the front and pull out. To

Push down the button and slide cover

close, push the drawer in and

backwards.

engage.

The rear carrier system (Flex-Fix

system) allows one bicycle to be

attached to an extendable carrier

integrated into the vehicle floor. It is

possible to attach two further bicycles

on an adapter. The transportation of

other objects is not permitted.

The maximum load of the rear carrier

system is 60 kg with attached adapter

and 30 kg without attached adapter.

This allows the attachment of an

electrically-powered bicycle to the

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

rear carrier system. The maximum

Caution

load per bicycle on the adapter is

20 kg.

Consult your bicycle dealer before

The wheelbase of a bicycle must not

attaching bicycles with carbon

exceed 1.15 metres. Otherwise the

frames. The bicycles may get

secure fastening of a bicycle is not

damaged.

possible.

If not in use, the rear carrier system

Notice

must be slid back into the vehicle

The tail lights of the vehicle will be

floor.

deactivated if the tail lights of the

There must not be any objects on the

rear carrier system are installed.

bicycles that could become loose

Extending

Pull release lever up. The rear carrier

during transportation.

Open the tailgate.

system disengages and travels

quickly out of the rear bumper.

Caution

9 Warning

If the rear carrier system is

No-one should be in the extension

extended and the vehicle is fully

zone of the rear carrier system,

loaded, the ground clearance will

risk of injury.

be reduced.

Drive carefully whenever the road

has a steep inclination or when

driving over a ramp, bump, etc.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

Completely pull out the rear carrier

Unfold number plate holder

Fold out tail lights

system until you hear it engage.

Ensure that it is not possible to push

in the rear carrier system without

pulling the release lever again.

9 Warning

It is only permissible to fit objects

to the rear carrier system if the

system has been correctly

engaged. If the rear carrier system

will not engage correctly, do not fit

objects to the system and slide the

system back. Seek the assistance

Lift the number plate holder and fold

To install the tail lights, remove both

of a workshop.

it backwards.

pins (1). Pull tail lights out of the

retainer towards the front (2) and

Affix the number plate before first use

downwards and swivel them to the

of the rear carrier system.

side.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

Remove strap and fold out the wheel

Assembling the bicycle rack

recess.

Lock the rear carrier system

Push the tail lights into the retainer

(1) and reinstall pins (2) all the way to

Lift the rack at the rear (1) and pull it

attach the lights.

backwards.

Fold out wheel recess

Fold up the rack (2).

Remove strap and swivel both

clamping levers sideways as far as

they will go.

Otherwise safe functionality is not

guaranteed.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

Push down the rack (1) and swivel

Make sure that the bicycle stands

handle (2) backwards to engage.

centrally on the wheel recesses.

Attaching a bicycle

2. Attach the short mounting bracket

Press button (1) and remove left part

to the bicycle frame. Turn the

of rack (2).

knob clockwise to fasten.

Press button (1) and insert left part of

rack into the right part (2).

1. Rotate the pedals into position, as

shown in the illustration, and put

the bicycle on the wheel recess.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

3. Secure both bicycle wheels to the

1. Apply the adapter to the rear

wheel recesses using the strap

carrier system, as shown in the

retainers.

illustration.

4. Check the bicycle to make sure it

is secure.

Caution

Ensure gap between bicycle and

vehicle is at least 5 cm. If

necessary, loosen handlebar and

swivel sideways.

4. Guide the strap attached to the

Attaching the adapter

adapter underneath the lever

When carrying more than one bicycle,

when folding back the rear carrier

the adapter must be fixed.

system. Fasten the strap.

2. Turn the lever (1) forwards and

hold it, then lower the adapter (2)

Attaching further bicycles

at the rear.

The attachment of further bicycles is

3. Release lever and check if the

similar to the attachment of the first

adapter is engaged securely.

bicycle. Additionally, some steps

must be considered:

1. Before putting on the bicycle,

always unfold the wheel recesses

for the next bicycle if necessary.

2. Always rotate the pedals into an

appropriate position before

putting on the bicycle.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

6. Additionally, secure both bicycle

wheels of the third bicycle to the

wheel recesses using the

tensioning straps.

It is recommended to attach a

warning sign to the rearmost bicycle,

to increase visibility.

Fold the rear carrier system

backwards

The rear carrier system can be folded

backwards to gain access to the load

Use the short accessory mounting

compartment.

3. Position the bicycles on the rear

bracket to attach the third bicycle.

carrier system alternately aligned

●

Without attached adapter:

The bracket must be fixed

to the left and to the right.

between the frames of the second

4. Align the bicycles with the one

and third bicycle.

attached previously. The wheel

hubs of the bicycles must not

touch each other.

5. Attach the bicycles with mounting

brackets and strap retainers as

described for the first bicycle. The

mounting brackets should be

fixed in parallel.

Use the long mounting bracket to

attach the second bicycle to the

Push the lever (1) to disengage

rack.

and hold it.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

Pull the rack (2) backwards to

To increase visibility, the tail lights of

fold the rear carrier system.

the vehicle are activated when the

rear carrier system is folded back.

● With attached adapter:

9 Warning

When folding the rear carrier

Take care when disengaging the

system forwards again, ensure

rear carrier system as it will tilt

that the system is engaged

backwards. Risk of injury.

securely.

Removing bicycles

Undo strap retainers on both bicycle

2. Unbutton the strap.

tyres.

Turn knob anticlockwise and remove

mounting brackets.

Detaching adapter

Detach the adapter before removing

the bicycle on the rear carrier system.

1. Fold in wheel recesses.

Hold frame (1) of rearmost

bicycle with one hand and pull the

loop (2) to disengage.

Hold rearmost bicycle with both

3. Turn the lever (1) forwards and

hands and fold the rear carrier

hold it.

system backwards.

4. Lift the adapter (2) at the rear and

remove.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

Disassembling the bicycle rack

Fold the rack backwards, then push

forwards until it stops (1).

Press the rack down at the rear (2).

Fold in wheel recess

Fold in wheel recess. Fasten strap.

Arrange mounting brackets as shown

in the illustration.

Press button (1) and remove upper

part of rack (2).

Swivel handle (1) sideways to

disengage and lift the rack (2).

Stow the strap retainers accurately.

Press button (1) and reinstall rack (2).

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

Unlock the rear carrier system

Retracting the rear carrier system

Caution

Ensure that all foldable parts, e.g.

wheel recesses and mounting

brackets, are stowed correctly.

Otherwise the rear carrier system

may get damaged when trying to

retract it.

Push the tail lights into the retainer

(1). Insert pins into the designated

Swivel both clamping levers inwards

holes of the retainer and the tail lights

as far as they will go. Fasten strap.

(2).

Fold in tail lights

Notice

Remove both pins. Pull tail lights out

Check that the tail lights of the

of the retainer and put them in the

vehicle are working properly.

position to be stored in.

Fold in number plate holder

Lift the number plate holder and fold

it forwards.

Push the release lever up and hold it.

Lift the system slightly and push it into

the bumper until it engages.

Release lever must return to original

position.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

Load compartment

9 Warning

If the system cannot be correctly

Load compartment extension

engaged, seek the assistance of a

workshop.

Caution

First fold down the rear seat

cushion before folding the rear

seat backrest.

Disregard may lead to damage to

the rear seat.

2. Pull the loop under the seat

1. Push head restraints down by

cushion and fold down the seat

pressing the catch.

cushion.

Notice

To ensure sufficient room for rear

seat cushion operation, slide the

front seat forward and move the front

seat backrest upright.

3. Pull the release lever on top of the

rear backrest.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

To return the backrest to the original

or caught under the seat cushion,

position, pull out the seat belt from the

then push the front part of the seat

belt guides and lift backrest up.

cushion firmly down until it latches.

Push backrest firmly into place.

Caution

9 Warning

When returning rear seat backrest

to the upright position, place the

When folding up, ensure that

rear seat belt and buckles

backrests are securely engaged in

between the rear seat backrest

position before driving. Failure to

and one cushion. Make sure the

do so may result in personal injury

rear seat belt and buckles do not

or damage to the load or vehicle in

get pinched under the rear seat

4. Fold the backrest forward and

the event of hard braking or a

cushion.

down.

collision.

Ensure the seat belts are not

Ensure the seat belts are not pinched

twisted or caught in the seat

by the latch.

backrest and are arranged in their

proper position.

The centre rear seat belt may lock

when you raise the backrest. If this

happens, allow the belt go back all the

way and repeat operation.

If the seat belt is still locked, fold down

the seat cushion and try again.

To return the rear seat cushion, put

the rear part of the seat cushion in its

original position ensuring that the

5. Put the seat belts for the outboard

seat belt buckle straps are not twisted

seats into the belt guides.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Storage

Mount the cover to the hook at the

Load compartment cover

Rear floor storage cover

sidewall.

Rear floor cover

Lashing eyes

The lashing eyes are designed to

secure items against slippage, e.g.

using lashing straps or luggage net.

Warning triangle

Do not place any objects on the cover.

Removing

Grasp the handle and lift the cover.

Unhook retaining straps from tailgate.

Lift cover at the rear and push it

upwards at the front.

Remove the cover.

Fitting

Stow the warning triangle below the

floor cover in the load compartment.

Engage cover in side guides and fold

Secure it with the strap.

downwards.

Attach retaining straps to tailgate.

Vauxhall Mokka X (2016 year). Manual - part 4