Porsche Cayenne (2010 year). Manual - part 8
Displaying important numbers and calling
Displaying missed calls, calling back
Setting speed limit on the multi-
party
purpose display
The IMPORTANT NOS. menu shows the entries
stored as important numbers on the SIM card.
The telephone numbers of the rejected calls are
A speed limit can be entered to monitor the driving
shown in the MISSED CALLS menu. The numbers
speed. When it is exceeded, a signal sounds and
1. MAIN MENU
are stored on the SIM card.
the multi-purpose display displays the message
> PHONE
LIMIT EXCEEDED.
> IMPORTANT NOS.
1.
MAIN MENU
Select and confirm.
> PHONE
Note on operation
2. Select entry from the list.
> MISSED CALLS
f For information on the operating principle of
Select and confirm.
3. Confirm selection.
the multi-purpose display:
2.
Select entry from the list.
Please see the chapter “OPERATING
3.
Confirm selection.
Displaying telephone book, selecting
PRINCIPLE” on Page 124.
party and calling
Accepting current speed
The PHONE BOOK menu shows the entries of the
telephone book that are stored on the SIM card.
You can define the current speed as the speed
limit in the menu MPH-LIMIT.
1. MAIN MENU
> PHONE
1. MAIN MENU
> PHONE BOOK
>MPH-LIMIT
Select and confirm.
Select and confirm
2. Select entry from the list.
2. Select CURRENT MPH.
3. Confirm selection.
3. Confirm selection.
LIMIT ACTIVE is activated automatically and
the selected speed limit is shown.
Multi-Purpose Display and Instruments
129
Presetting speed
Activating or deactivating the limit
Example: Front side light warning message
You can define a speed limit in the menu
Displaying warning messages
1. MAIN MENU
MPH-LIMIT.
>MPH-LIMIT
All current warnings and information relating to the
Select and confirm.
1. MAIN MENU
traffic safety of the vehicle can be displayed in the
>MPH-LIMIT
2. Select LIMIT ACTIVE.
menu WARNINGS.
Select and confirm.
3. Confirm selection.
2. Select MPH SET.
LIMIT ACTIVE is activated
Danger!
3. Set desired limit:
LIMIT ACTIVE is deactivated
Warning messages indicate possible faults.
- Press briefly: Limit is set in increments of
4. Select BACK.
f Go to an authorized Porsche dealer
1 mph (around 1.6 km/h).
5. Confirm selection.
immediately.
- Press for longer than 2 seconds: Limit is set
Sub-menu MPH-LIMIT is displayed.
in increments of 10 mph (16 km/h).
4. Confirm selection.
LIMIT ACTIVE is activated automatically.
130 Multi-Purpose Display and Instruments
1. MAIN MENU
Displaying status of level control
Displaying status of locks/reduc-
>VEHICLE INFO
tion
The ground clearance of vehicles equipped with
Select and confirm.
level control is shown in the LEVEL menu.
The selected driving programs for Low Range/
2. Select WARNINGS.
High Range as well as the engaged locks can be
3. Confirm selection.
1. MAIN MENU
displayed.
NO WARNING is displayed if the vehicle is in
>VEHICLE INFO
perfect condition. Any warning messages
Select and confirm.
1. MAIN MENU
which are present are displayed.
2. Select LEVEL.
>VEHICLE INFO
4. Press repeatedly to display the warnings one
3. Confirm selection.
Select and confirm.
after the other.
The current level settings are displayed.
2. Select LOCKS/REDUCT.
5. Confirm selection.
4. Confirm selection.
3. Confirm selection.
VEHICLE INFO menu is displayed.
VEHICLE INFO menu is displayed.
The current settings for
- Longitudinal lock on/off
Note on operation
Note on operation
- Reduction on/off
f
For information on the operating principle of
- Transverse axle differential lock on/off are
The level control is adjusted by means of the
the multi-purpose display:
displayed.
rocker switch behind the gearshift lever in the
Please see the chapter “OPERATING
center console.
4. Confirm selection.
PRINCIPLE” on Page 124.
VEHICLE INFO menu is displayed.
For information on level control and height
adjustment:
Note on operation
Please see the chapter “AIR SUSPENSION WITH
LEVEL CONTROL AND HEIGHT ADJUSTMENT” on
The driving programs are set by means of the
Page 190.
rocker switch behind the gearshift lever in the
center console.
f For information on the programs for Off Road
and On Road driving and engaging locks/
reduction:
Please see the chapter “DRIVING PROGRAMS
FOR ON-ROAD AND OFF-ROAD DRIVING” on
Page 177.
Multi-Purpose Display and Instruments
131
damage with tire sealant or fit the spare wheel.
f
Do not by any means continue to drive with
leaking tires.
f
Sealing the tire with the tire sealant is only an
emergency repair so you can drive to the next
authorized Porsche dealer.
The maximum permitted speed is 50 mph
(80 km/h).
f
Defective tires must be immediately replaced
Displaying average consumption
Setting Tire Pressure Monitoring
by an authorized Porsche dealer.
Tire repairs are not permissible under any
1. MAIN MENU
Danger!
circumstances.
>VEHICLE INFO
Risk of serious personal injury or death.
f
Do not drive with tires whose tire pressure
Select and confirm.
Driving the vehicle with low tire pressure
drops again in a short period of time. Have
2. Select Ø
CONSUM.
increases risk of a tire failure and resulting
tires checked by an authorized Porsche dealer.
3. Confirm selection.
loss of control. Furthermore, low tire
f
If Tire Pressure Monitoring is defective (e.g.
The average consumption is displayed.
pressure increases rate of wear of the
defective wheel transmitters), contact an
The displayed value is based on the distance
affected tires.
authorized Porsche dealer immediately and
travelled since the last reset to “zero”.
Despite the advantages offered by Tire
have the damage repaired.
Pressure Monitoring, it is not a substitute for
Resetting average consumption
The tire pressure will not be monitored by
proper tire maintenance, and it is still the
defective Tire Pressure Monitoring.
4. Select RESET.
driver’s responsibility to update the settings
For information on warning messages on the
5. Press the ENTER button for longer than
in the multi-purpose display and maintain the
multi-purpose display: Please see the chapter
1 second.
correct tire pressure, even if under-inflation
“OVERVIEW OF WARNING MESSAGES” on
The value is set to “- -.-”.
has not reached the level to trigger illumina-
Page 149.
tion of Tire Pressure Monitoring low tire
f
Tire Pressure Monitoring gives a warning about
Note on operation
pressure message. Low tire pressure
tire damage due to insufficient tire pressure as
reduces the road safety of the vehicle and
f For information on the operating principle of
well as about a gradual loss of pressure due to
destroys the tire and wheel.
the multi-purpose display:
foreign objects. Tire Pressure Monitoring
Please see the chapter “OPERATING
f When a flat tire has been displayed, immedi-
cannot warn you about tire damage that
PRINCIPLE” on Page 124.
ately stop in a suitable place and check the
occurs suddenly (e.g. flat tire due to acute
tires for damage. If necessary, remedy the
external effects).
132 Multi-Purpose Display and Instruments
f
If a tire pressure message is displayed, correct
The display as well as the settings for Tire
Warning light
the tire pressure at the next opportunity.
Pressure Monitoring take place on the multi-
purpose display in the sub-menu
f
Incomplete entries or selection of the wrong
TYRE PRESSURE.
tires on the multi-purpose display affect
Warning!
However, the tire pressure must still be set
correct indication of warnings and messages.
manually on the wheel.
Your vehicle has also been equipped with a TPM
The settings in the TYRE PRESSURE menu
malfunction indicator to indicate when the system
must be updated after wheel changes, use of
The deviations in the tire pressures from the
is not operating properly.
a spare wheel or changes in vehicle loading.
required pressures are shown in the sub-menu
The TPM malfunction indicator is combined with
TYRE PRESSURE.
f
Use only the pressure differences shown in the
the low tire pressure telltale.
TYRE PRESSURE menu or from tire pressure
Example:
When the system detects a malfunction, the
messages or warnings when correcting the
If the tire pressure display shows “-4 psi
telltale will flash for approximately one minute and
tire pressure.
(-0.3 bar)”, you must increase the tire pressure by
then remain continuously illuminated. This
4 psi (0.3 bar).
sequence will continue upon subsequent vehicle
f
Tires lose air over time without a tire defect
start-ups as long as the malfunction exists.
being present. A tire pressure warning will then
The tire pressures to be monitored are fixed in the
When the malfunction indicator is illuminated, the
appear on the multi-purpose display.
Tire Pressure Monitoring system and cannot be
system may not be able to detect or signal low tire
Correct tire pressure.
changed.
pressure as intended.
The following settings must be made to permit
TPM malfunctions may occur for a variety of
correct monitoring.
reasons, including the installation of replacement
Functional description of Tire Pressure
or alternate tires or wheels on the vehicle that
Monitoring
- Tires
prevent the TPM from functioning properly.
Select the type and size of the tires fitted on
Tire Pressure Monitoring continuously monitors
Always check the TPM malfunction telltale after
the vehicle.
tire pressure and tire temperature on all four
replacing one or more tires or wheels on your
wheels and warns the driver when the tire
- Load
vehicle to ensure that the replacement or alternate
pressure is too low.
Select the type of loading.
tires and wheels allow the TPM to continue to
function properly.
Note on operation
Settings can be made only when the vehicle is
stationary.
f For information on tires and wheels:
Please see the chapter “TIRES/WHEELS” on
Page 281.
Multi-Purpose Display and Instruments
133
After driving off, the system starts to teach the
wheels and wheel positions on the vehicle. During
this time, the tire pressure warning light on the
speedometer flashes about 60 seconds and lights
up thereafter permanently, and no current tire
pressure information is available on the displays.
Note
Information on the tire size and type can be found
on the tire sidewall. For further information on the
Setting the tire type and size
Note on operation
details on the tire sidewall:
f
For information on the operating principle of
f Please see the chapter “INSCRIPTION ON
Warning!
the multi-purpose display:
RADIAL TIRE” on Page 290.
Please see the chapter “OPERATING
Incomplete entries or selection of the wrong
tires on the multi-purpose display affect
PRINCIPLE” on Page 124.
Note on operation
correct indication of warnings and
1.
MAIN MENU
Before fitting tires approved by Porsche with a
messages.
>TYRE PRESS.
size which is not already stored in the multi-
f The settings must be updated in the TYRE
>SETTINGS
purpose display, the missing information should
PRESSURE menu after changing a wheel, filling
Select and confirm.
be supplemented in the multi-purpose display.
with tire sealant or adding air (after previous
2.
Select TYRES.
f Go to an authorized Porsche dealer
warning “Flat tyre”).
immediately.
3.
Confirm selection.
f Please see the chapter ““FLAT TYRE”
The TYRE TYPE list is displayed.
WARNING” on Page 136.
4.
Select tire type (e.g. SUMMER).
The list with the possible tire sizes (e.g. for the
The settings of the multi-purpose display must be
selection SUMMER) is displayed.
updated after changing wheels or tires on the
5.
Select tire size (e.g. 18 inch).
vehicle.
6.
Confirm selection.
The tire type and tire size must be selected even
The current settings are displayed.
if the settings for the new set of wheels are the
same as for the old wheels.
134 Multi-Purpose Display and Instruments
Warning!
1. MAIN MENU
Risk of accident due to excessive speed. This
>TYRE PRESS.
could lead to serious personal injury or
>SETTINGS
death.
Select and confirm.
f Always observe the permissible maximum
2. Select LOAD.
speed of the respective tire.
3. Confirm selection.
The LOAD menu is displayed.
f Exceeding maximum tire speed could result in
Select corresponding load type (e.g. FULL
a tire burst, causing loss of control of the
LOAD).
vehicle. This could lead to serious personal
injury or death.
Setting vehicle loading and adjusting tire
4. Confirm selection.
Moreover, Porsche recommends obeying all
pressure
The set load status is shown.
traffic laws at all times to maintain the safety
Deviations from the required pressure are shown
The tire pressure must be adjusted according to
of yourself and all vehicle occupants.
in the sub-menu MAIN MENU>TYRE
the vehicle load.
PRESSURE>SETTINGS (filling information).
The speed code letter indicates the maximum
A distinction is made between two types of
permissible speed for the tire.
loading:
f Correct the tire pressure according to this
f This letter appears on the tire sidewall:
information.
- Partial load
Please see the chapter “INSCRIPTION ON
up to 3 people and 46 lbs (21 kg) of luggage
RADIAL TIRE” on Page 290.
- Full load
more than 3 people and 46 lbs (21 kg) of
luggage
Multi-Purpose Display and Instruments
135
- Changing wheel with spare wheel or
collapsible spare wheel
For information on jacking up the vehicle:
Please see the chapter “LIFTING THE VEHICLE
WITH A LIFTING PLATFORM OR GARAGE LIFT”
on Page 298.
For information on changing a wheel:
Please see the chapter “LIFTING THE VEHICLE
WITH A JACK” on Page 299.
“Flat tyre” warning
The display shows: SELECTION AFTER WARNING
or
The warning threshold for output of this warning
1.
Stop the vehicle immediately in a suitable
- Sealing with tire sealant.
message is speed-dependent.
place.
For information on handling and filling the
At a speed of below 100 mph (160 km/h), this
2.
Check the indicated wheel for damage.
sealant: Please see the chapter “USING TIRE
warning indicates a pressure loss of at least 7 psi
SEALANT” on Page 296.
(0.5 bar); at a speed of above 100 mph
3.
Fill the tire or change the wheel, as appro-
(160 km/h), the warning indicates a pressure loss
priate.
4.
Switch ignition on again.
of at least 6 psi (0.4 bar). The message indicates
The “Flat tyre” warning first appears again on
- Adding air
the wheel in which the pressure loss has been
the multi-purpose display. The display changes
Example: If the tire pressure display shows
detected. The deviation from the required
to SELECTION AFTER WARNING after a few
“-7 psi (---0.5 bar)”, you must increase the tire
pressure is displayed for the corresponding
seconds.
pressure by 7 psi (0.5 bar).
wheel. The tire pressure warning light on the
On vehicles without air suspension:
5.
Select the action which has been carried out
speedometer lights up in addition to the warning
Please see the chapter “CHECKING TIRE
on the vehicle on the display with the rocker
message. This significant pressure loss is a
PRESSURE WITH A PRESSURE GAGE” on
switch.
danger to road safety.
Page 306.
- ADD AIR or
f The warning message can be acknowledged
On vehicles with air suspension:
while driving.
- WHEEL CHANGE > SPARE WHEEL > Spare
Please see the chapter “INFLATING TIRES ON
To do this, press the ENTER button on the
wheel type or
VEHICLES WITH AIR SUSPENSION” on
wiper stalk. The tire pressure warning light on
Page 308.
- SEALING SET
the speedometer remains lit.
The measure display SELECTION AFTER
or
6.
Press the ENTER button.
WARNING appears only after the ignition is
switched back on again.
136 Multi-Purpose Display and Instruments
Warning!
Note
Risk of accident, resulting in serious
If a collapsible spare wheel or tire sealant is used,
personal injury or death. The spare wheel
a warning reminder appears on the multi-purpose
and collapsible spare wheel are not equipped
display if the speed limit of 50 mph (80 km/h) is
with wheel transmitters and are not
exceeded.
monitored by Tire Pressure Monitoring.
Note on operation
f The spare wheel and collapsible spare wheel
If you do not confirm a selection or confirm a
must be used only over short distances.
selection without carrying out the task described
for this selection, this will affect correct indication
“Tyre pressure too low” message
Warning!
of warnings and messages.
Depending on the selection made, a corre-
Risk of accident resulting in serious personal
This message indicates pressure loss of at least
sponding message will appear when the ignition is
injury or death if a collapsible spare wheel or
4 psi (0.3 bar).
switched on, when driving off or while driving.
tire sealant is in use.
The message indicates the wheel in which the
For further information on warning messages on
pressure loss has been detected. The deviation
f
Avoid hard acceleration and high cornering
the multi-purpose display:
from the required pressure is displayed for the
speeds.
Please see the chapter “OVERVIEW OF WARNING
corresponding wheel.
f
Do not exceed maximum speed of 50 mph
MESSAGES” on Page 149.
The message appears only when the vehicle is
(80 km/h).
stationary. It appears for the first time when the
f
Please observe the safety and operating
ignition is switched off and then each time the
instructions on the tire compressor.
ignition is switched on until the tire pressure has
been corrected to the required value.
f
Have the tire or wheel replaced by an
authorized Porsche dealer as soon as
The message is shown for 10 seconds on the
possible.
multi-purpose display. It can be suppressed
immediately by pressing the ENTER button.
f Check the tire pressure at the next opportunity
and fill the tires.
Example: If the tire pressure display shows
“-4 psi (-0.3 bar)”, you must increase the tire
pressure by 4 psi (0.3 bar).
Multi-Purpose Display and Instruments
137
The spare wheel and collapsible spare wheel are
Setting spare wheel.
not equipped with wheel transmitters and are not
monitored by Tire Pressure Monitoring.
1.
MAIN MENU
>TYRE PRESS.
>SETTINGS
Wheel change (without warning)
> TYRES
> SPARE WHEEL
The settings of the multi-purpose display must be
Select and confirm.
updated after changing wheels or tires on the
vehicle.
2.
Select SPARE WHEEL.
Please see the chapter “SETTING THE TIRE TYPE
3.
Confirm selection.
The spare wheel is not equipped with a wheel
AND SIZE” on Page 134.
The display automatically returns to the TYRE
transmitter and is not monitored by Tire Pressure
PRESSURE sub-menu (filling information).
Monitoring. The tire pressure warning light on the
Setting spare wheel/sealant (without
The required tire pressures are displayed
speedometer flashes about 60 seconds and lights
warning)
here.
up thereafter permanently when the ENTER button
Select BACK.
is pressed. The value “_” is displayed in the sub-
If you have fitted a spare wheel or collapsible
4.
Confirm selection.
menu TYRE PRESSURE (filling information) at the
spare wheel or used tire sealant without being
The basic display appears.
position of the spare wheel.
requested to do so by a “Flat tyre” warning on the
multi-purpose display, you must subsequently
The reminder SPARE WHEEL/SEALING SET
update the settings in the TYRE PRESSURE sub-
OPERATION? appears each time the ignition is
menu.
switched on. For information on spare wheel/
sealing set operation: Please see the chapter
“NOTE ON SPARE WHEEL/SEALING SET OPERA-
TION” on Page 140.
138 Multi-Purpose Display and Instruments
Warning!
Setting collapsible spare wheel.
Warning!
Risk of accident, resulting in serious
1. MAIN MENU
Risk of accident, resulting in serious
personal injury or death. The spare wheel is
>TYRE PRESS.
personal injury or death. The collapsible
not equipped with a wheel transmitter and is
>SETTINGS
spare wheel is not equipped with a wheel
not monitored by Tire Pressure Monitoring.
transmitter and is not monitored by Tire
> TYRES
Pressure Monitoring.
f
The spare wheel must be used only over short
> SPARE WHEEL
distances.
Select and confirm.
f The collapsible spare wheel must be used only
For information on handling and fitting/
2. Select COLLAP. WHEEL.
over short distances.
removing the spare wheel: Please see the
3. Confirm selection.
For information on handling the collapsible
chapter “SPARE WHEEL” on Page 309.
The required pressure and speed limit for the
spare wheel: Please see the chapter
collapsible spare wheel are displayed.
“COLLAPSIBLE SPARE WHEEL” on Page 305.
The collapsible spare wheel is not equipped with a
wheel transmitter and is not monitored by Tire
Warning!
Pressure Monitoring. The tire pressure warning
Risk of accident, resulting in serious
light on the speedometer flashes about
personal injury or death if a collapsible spare
60 seconds and lights up thereafter permanently
wheel is in use.
when the ENTER button is pressed. The value “_”
is displayed in the sub-menu TYRE PRESSURE
f Avoid hard acceleration and high cornering
(filling information) at the position of the
speeds.
collapsible spare wheel.
f Do not exceed maximum speed of 50 mph
A warning appears on the multi-purpose display if
(80 km/h).
the speed limit of 50 mph (80 km/h) is exceeded.
f Please observe the safety and operating
The reminder SPARE WHEEL/SEALING SET
instructions on the tire compressor.
OPERATION? appears each time the ignition is
f Have the collapsible spare wheel replaced by
switched on.
an authorized Porsche dealer as soon as
For information on spare wheel/sealing set opera-
possible.
tion: Please see the chapter “NOTE ON SPARE
WHEEL/SEALING SET OPERATION” on Page 140.
139
Multi-Purpose Display and Instruments
Setting tire sealant/sealing set
Warning!
Note on spare wheel/sealing set operation
1. MAIN MENU
Risk of accident, resulting in serious
Each time the ignition is switched on,
>TYRE PRESS.
personal injury or death if a tire repaired with
the reminder SPARE WHEEL/SEALING SET
>SETTINGS
tire sealant is in use.
OPERATION? appears for approx. 10 seconds if a
> TYRES
f
Avoid hard acceleration and high cornering
spare wheel type (spare wheel, collapsible spare
> SPARE WHEEL
speeds.
wheel or sealing set) has been set.
Select and confirm.
f
Do not exceed maximum speed of 50 mph
2. Select SEALING SET.
1.
Select YES or NO:
(80 km/h).
3. Confirm selection.
- YES if a spare wheel, collapsible spare wheel
The display automatically returns to the TYRE
f
Please observe the safety and operating
or tire sealant is still being used.
PRESSURE sub-menu (filling information).
instructions on the tire compressor.
- NO if the spare wheel, collapsible spare
wheel or tire sealant has been removed.
f
Use tires repaired with sealant only over short
f Inflate tires according to the displayed
2.
Confirm selection.
distances.
pressure differences.
The selected item is then accepted.
For information on handling and filling the
A warning appears on the multi-purpose display if
The current settings are displayed if NO is
sealant: Please see the chapter “USING TIRE
the speed limit of 50 mph (80 km/h) is exceeded.
selected.
SEALANT” on Page 296.
The reminder SPARE WHEEL/SEALING SET
OPERATION? appears each time the ignition is
switched on.
For information on spare wheel/sealing set opera-
tion: Please see the chapter “NOTE ON SPARE
WHEEL/SEALING SET OPERATION” on Page 140.
140 Multi-Purpose Display and Instruments
- at least three wheel transmitters for Tire
Faults in Tire Pressure Monitoring
Pressure Monitoring are faulty or not present,
In the event of faults, Tire Pressure Monitoring
- temporarily after changing a wheel,
cannot monitor the tire pressure. A distinction is
- too many wheel transmitters have been
made between partial monitoring and inactive
detected,
system.
In the case of partial monitoring, the tire pressure
- there is external interference by other radio
warning light on the speedometer flashes about
sources, e.g. wireless headphones,
60 seconds and lights up thereafter permanently.
- tire temperatures are too high.
No message is output on the multi-purpose
f Set the fitted wheel set with tire type and tire
display.
f For information on messages on the multi-
size.
If Tire Pressure Monitoring is not active, the tire
purpose display:
Please see the chapter “SETTING THE TIRE
pressure warning light on the speedometer
Please see the chapter “OVERVIEW OF
TYPE AND SIZE” on Page 134.
flashes about 60 seconds and lights up thereafter
WARNING MESSAGES” on Page 149.
Note on operation
permanently. A corresponding message is output
on the multi-purpose display.
The reminder SPARE WHEEL/SEALING SET
Notes on tire pressure
The warning light goes out as soon as all faults
OPERATION? goes out automatically after approx.
have been remedied.
Pressure increase as the result of tempera-
10 seconds if no selection is made during this
ture increase
time. The original selection “YES” is then
Tire Pressure Monitoring switches to partial
maintained.
monitoring if:
In accordance with physical principles, the tire
pressure changes as the temperature changes.
- there are up to two wheel transmitters not
The tire pressure increases or decreases by
present or faulty (e.g. a spare wheel or collap-
around 1.5 psi (0.1 bar) for every 18 °F (10 °C)
sible spare wheel is fitted that does not have a
change in temperature.
wheel transmitter).
In the event of partial monitoring, the value “_” is
Tire pressure specifications
displayed in the sub-menu TYRE PRESSURE (filling
The tire pressure must match the prescribed value
information) at the position of the faulty or missing
(required pressure).
wheel transmitter.
You can find information on the tire pressure for
Tire Pressure Monitoring is not active in the
cold tires 68 °F (20 °C):
following cases:
- Tire Pressure Monitoring is faulty,
Multi-Purpose Display and Instruments
141
- in the sub-menu TYRE PRESSURE (filling infor-
Switching off passenger compart-
mation):
ment monitoring on the multi-
as a required pressure for each axle if Tire
Pressure Monitoring has not yet been taught
purpose display
the corresponding values,
The passenger compartment monitoring system
- in the front left door aperture for each wheel,
can be temporarily deactivated in the ALARM sub-
menu.
- in the Technical Data chapter in this Owner’s
When the doors are locked again, the ultrasound
Manual: Please see the chapter “TIRE
passenger compartment monitoring system is
PRESSURES, COLD (68 °F/20 °C)” on
activated once more.
Page 354.
Further important information concerning this
Switching passenger compartment
If Tire Pressure Monitoring has been taught the
topic can be found in a separate chapter:
monitoring on/off
corresponding values, the deviations from the
f Please see the chapter “TEMPORARILY
The alarm is triggered if motion is detected in the
required pressure are shown in the sub-menu
DEACTIVATING PASSENGER COMPARTMENT
interior with the doors closed (e.g. if a window is
TYRE PRESSURE (filling information) indepen-
MONITORING SYSTEM” on Page 246.
broken in a theft).
dently of the tire temperature. The correct tire
pressure adjustment can be made for a wheel on
Notes on operation
1.
MAIN MENU
the basis of this display information even if the
f Comfort settings can be made only when the
>SETTINGS
tires are warm.
vehicle is stationary.
> COMFORT
Insufficient tire filling pressure can cause tires to
> ALARM
overheat when driving and thus be damaged -
f For information on the operating principle of
Select and confirm.
even invisibly.
the multi-purpose display:
2.
Select INTERIOR.
Hidden tire damage is not eliminated by subse-
Please see the chapter “OPERATING
3.
Confirm selection.
quently correcting the tire pressure.
PRINCIPLE” on Page 124.
Monitoring is activated.
f For this reason, always make sure that the tire
Monitoring is deactivated.
pressure is correct.
f For further information on maintenance and
care of tires and wheels:
Please see the chapter “TIRES/WHEELS” on
Page 281.
142 Multi-Purpose Display and Instruments
Changing settings for opening and
Setting door unlocking
locking the vehicle
Door unlocking can be set on an individual basis.
Note on operation
1.
MAIN MENU
Comfort settings can be made only when the
>SETTINGS
vehicle is stationary.
> COMFORT
> DOOR OPENING
You can set different variants of locking and
> DOORS
unlocking the doors and the rear lid as well as the
Select and confirm.
check-back signal when locking and unlocking the
Synchronous adjustment of door
2.
Select one of the three options:
vehicle and save them on the respective remote
mirrors
control.
- SINGLE DOOR
Only the driver’s door is unlocked.
1. MAIN MENU
The door on the access side is unlocked on
Note on operation
>SETTINGS
vehicles equipped with Porsche Entry & Drive.
Comfort settings can be made only when the
> COMFORT
- VEH. SIDE
vehicle is stationary.
> DOOR OPENING
Both doors on the driver’s side are unlocked.
When this function is active, the mirrors move
Select and confirm.
The doors on the access side are unlocked on
simultaneously and in the same direction.
2. Set the desired function.
vehicles equipped with Porsche Entry & Drive.
3. Switch ignition off.
- ALL
1. MAIN MENU
4. Close the driver’s door.
All doors are unlocked.
>SETTINGS
5. Press button on the car key.
3.
Confirm selection.
> COMFORT
> MIRRORS
The settings are now stored on this car key.
Note on operation
Select and confirm.
Note on operation
If the unlocking button
on the remote control
2. Select SYNCH.
f For information on the operating principle of
is pressed a second time within 2 seconds, all
3. Confirm selection.
the multi-purpose display:
vehicle doors are unlocked, independent of the
SYNCHRONOUS ADJUSTMENT is
Please see the chapter “OPERATING
affected setting.
activated.
PRINCIPLE” on Page 124.
SYNCHRONOUS ADJUSTMENT is deacti-
vated.
Multi-Purpose Display and Instruments
143
Setting rear lid locking
Setting AUTO LOCK (automatic door
locking) and AUTO UNLOCK (automatic
When the TAILGATE function is active, rear access
door unlocking)
(rear lid, rear window and spare wheel bracket) is
included in the central locking system.
1. MAIN MENU
Access is possible when the vehicle is stationary
>SETTINGS
and unlocked.
> COMFORT
At speeds higher than 4 mph (6 km/h), release is
> DOOR OPENING
blocked until a door is opened with the vehicle
Select and confirm.
stationary.
2. Select AUTO LOCK or AUTO UNLOCK.
Setting door opening signal
When the TAILGATE function is deactivated,
3. Confirm selection.
If the function TURN SIGNALS is active, door
access is only possible using button
on the
Selection is activated.
unlocking and locking is confirmed by the
remote control.
Selection is deactivated.
emergency flashers flashing.
1. MAIN MENU
AUTO LOCK and AUTO UNLOCK variants
If the function HORN is active, door unlocking and
>SETTINGS
locking is confirmed by an acoustic signal.
> COMFORT
You can set 4 different variants of automatic door
> DOOR OPENING
locking (AUTO LOCK) and automatic door
1.
MAIN MENU
Select and confirm.
unlocking (AUTO UNLOCK).
>SETTINGS
2. Select TAILGATE.
Doors locked using AUTO LOCK can always be
> COMFORT
> DOOR OPENING
3. Confirm selection.
opened by pulling the inner door handle twice
Function is activated.
regardless of the setting for door unlocking.
> SIGNAL
Select and confirm.
Function is deactivated.
Option 1:
2.
Select TURN SIGNALS or HORN.
AUTO LOCK off and AUTO UNLOCK off
3.
Confirm selection.
Note on operation
The doors do not lock and unlock automatically.
Selection is activated.
Vehicles with powerliftgate:
Selection is deactivated.
Regardless of the setting in the multi-purpose
Option 2:
display, the rear lid can be opened by pulling the
AUTO LOCK on and AUTO UNLOCK off
button in the driver’s door when the vehicle is at a
Doors lock automatically when a speed of approx.
standstill with the ignition switched on.
4 mph (6 km/h) is exceeded.
Please see the chapter “POWERLIFTGATE (REAR
LID)” on Page 23.
144 Multi-Purpose Display and Instruments
Option 3:
1. MAIN MENU
AUTO LOCK on and AUTO UNLOCK on
> SETTINGS
Doors lock automatically when a speed of approx.
> LIGHTS
4 mph (6 km/h) is exceeded.
Select and confirm.
On vehicles without Porsche Entry & Drive, the
2. Select DAYTIME DRIVING LIGHTS.
doors are unlocked automatically when the
3. Confirm selection.
ignition key is withdrawn.
Function ist activated.
On vehicles equipped with Porsche Entry & Drive,
Function ist deactivated.
the doors are unlocked when the ignition is
Switching daytime driving lights
switched off twice.
Canada only:
on/off
Option 4:
The DAYTIME DRIVING LIGHTS function cannot be
AUTO LOCK off and AUTO UNLOCK on
Note on operation
deactivated.
The doors do not lock automatically.
The options in the LIGHTS menu can only be set
when the vehicle is stationary.
If the doors are locked with the central locking
system button:
USA only:
On vehicles without Porsche Entry & Drive, the
doors are unlocked automatically when the
You can activate/deactivate the daytime driving
ignition key is withdrawn.
lights on the multi-purpose display in the instru-
ment panel.
On vehicles equipped with Porsche Entry & Drive,
the doors are unlocked when the ignition is
switched off twice.
Multi-Purpose Display and Instruments
145