Snowmobile Polaris 600 IQ Widetrak (2017 year). Manual - part 9

39

FEATURES

Instrumentation

MFD Digital Display Programs

Performance Program
Trip Settings

Trip F automatically displays when the 
fuel level is low if the snowmobile is 
equipped with an electronic fuel gauge. 
The fuel symbol and the last fuel bar on 
the MFD gauge (if equipped) will blink 
when the fuel level reaches 1/8 of a tank.

The Trip F odometer records distance 
traveled, and the fuel symbol continues 
to blink, until enough fuel is added to 
raise the level above 1/4 of a tank. The 
Trip F odometer will automatically reset 
to zero after refueling.

40

FEATURES

Instrumentation

MFD Digital Display Programs

Performance Program
Clock Setting (if equipped)

1. Enter the Performance Program.

2. Press and release the SET button 

until the clock screen is active.

3. Press and hold the SET button for 

five seconds.

4. When the hour starts flashing, 

press the SET switch once to advance one hour. (Press and hold the 
SET button to advance the hours quickly.)

5. Press and release the MODE button to save the hour. The minutes 

will begin flashing.

6. Set the minutes in the same manner.

7. When finished, press and release the MODE button to save the new 

setting. If the MODE button is not pressed within ten seconds, the 
gauge will automatically save the new entry.

41

FEATURES

Instrumentation

MFD Digital Display Programs

Engine Program

Press and release the MODE button until the engine program screen is 
active. The default display for this screen includes engine hours, 
electrical system voltage level, fuel level (if equipped) and either engine 
coolant temperature, air temperature (accessory) or altimeter 
(accessory).

Press and release the SET button to cycle through the following screens: 
hour meter, engine temperature, air temperature (available as an 
accessory), altimeter (available as an accessory) and turbo boost (if 
equipped).

Hour Meter

The hour meter records the total hours of 
engine operation since manufacture. This 
meter cannot be reset.

Engine Temperature

A thermometer measures water temperature, 
giving an indication of engine temperature.

Air Temperature (if equipped)

The MFD displays actual air temperature in 
either standard or metric units.

1. Enter the Engine Program.

2. Press and hold the MODE switch for ten 

seconds to switch between standard and 
metric units of measurement.

42

FEATURES

Instrumentation

MFD Digital Display Programs

Engine Program
Altitude (if equipped)

The rider can calibrate the altimeter for current 
atmospheric conditions. Altimeter accuracy 
will be +/-300 ft. (91 m) after adjustment.

1. Enter the Engine Program.

Tip: Press and hold the MODE switch for ten sec-

onds to switch between standard and metric 
units of measurement. When "ALt" displays, 
the program is in the metric mode.

2. Press and release the SET button until the altimeter screen is active.

3. Press and hold the SET button for five seconds. When the digits 

begin to flash, release the button. 

4. Press and release the SET button once to advance 50 feet (15 m).

Tip: Press and hold the SET button to advance quickly by 100-foot (30 m) 

increments.

5. Adjust the altitude display to within 50 ft. (15 m) of current altitude.

Tip: The gauge reads barometric pressure and allows the rider to compensate 

for daily fluctuations in air pressure. The gauge can adjust the displayed 
altitude to +/- 1300 ft. (396 m) from the preset value. It will adjust up to 
+1300 ft. (396 m) above the calibrated altitude. Once the +1300 ft. (396 m) 
offset has been reached, the next adjustment is -1300 ft. (396 m) from the 
calibrated altitude, and 50 ft. (15 m) will be added to the altitude each time 
the SET button is pressed.

6. Press and release the MODE button to set the reading at the adjusted 

value. If the MODE button is not pressed within ten seconds, the 
gauge will automatically save the new entry.