COMBINE HARVESTER AW70V, VNQ, AW82V, VNQ. Manual - part 2

Safety Instructions

 

9 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Check the brake and control levers.

 

It will be very dangerous if the brake does not work or   
there is deviation in the control levers. Be sure to check   
and adjust the same. 
 
[If not] 
Personal injury or damages to the machine may be caused. 
 

 

Be sure to properly fix the panel covers dismounted.

 

Make sure to replace the panel covers dismounted during checking   
prior to starting up and operation. Ensure the covers are not deformed 
or damaged. Keep your hands, feed and clothes away from the running parts. 
 
[If not] 
Person injury may be caused. 

Do not 

forget to put   

the cover. 

 

Clean up straw near the engine, muffler and belt pulley. 
Check whether there is straw, dust or fuel attached on the engine, 
muffler and belt pulley before daily operation. 
 
[If not] 
Dust may be ignited and cause fire or personal injury. 

Discharged straw 

causes a fire. 

 

Put all control levers in the neutral position when starting up the engine.

 

Be sure to sit in the driver’s seat and put all control levers in the neutral   
position before starting up the engine. 
 
[If not] 
The engine may not be started up. 

Safety Instructions

 

10 

 

 
4. Precautions for operation and moving

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Never park on slope.

 

Wood blocks must be used for preventing sliding, and at   
the same time, the brake pedal must be locked if you   
have to park the machine on a slope. 
 
[If not] 
The machine may slide and cause accident. 

 

Do not drive close to road edge.

 

Do not come close to the road edge or slippery road surface   
while driving. 
 
[If not] 
The road edge may collapse and cause turn-over of the   
machine or personal injury. 

 

Use the gangplank when crossing a ridge or ditch. 
Be sure to use the gangplank of the width, length and strength   
suitable for the machine when entering the field, crossing a ditch   
or high ridge, or passing through a soft field. 
 
[If not] 
The machine may loss balance, fall over and cause injuries. 

 

Be sure to comply with relevant laws and regulations, and wear the safety helmet.

 

You are required to abide by relevant laws and regulations,   
and for safety consideration, wear the safety helmet during working and driving on road. 
 
[If not] 
Unexpected injuries may be caused. 

Safety Instructions

 

11 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sound the horn for signaling before starting slowly. 
Check the surroundings and give a signal to remind the workers   
around of safety before starting the machine slowly. 
 
[If not] 
Person injury may be caused. 

 

Do not carry anyone else.

 

Do not carry anyone else in the machine or let others come close during driving. 
 
[If not] 
Unexpected injuries may be caused. 

 

Do not operate the range shift lever while ascending or descending a slope. 
Do not stop the machine or operate the auxiliary shift lever while ascending a slope. 
 
[If not] 
The machine may run backward and cause accident. 

 

Pay attention to the gravity center of the machine on an inclined ground. 
Get off the machine and operate on the ground if the angle of inclination   
at any points in the front/rear or left/right side of the combine exceeds 10 degrees. 
 
[If not] 
The machine may loss balance, fall over and cause injuries. 

Safety Instructions

 

12 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5. Precautions for loading/unloading

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjust the speed according to road and working condition. 
Do not turn the machine abruptly while ascending or descending a slope. 
Pay attention to the machine width and turning space for the rear part   
for the driving performance may be affected by its working status and 
road conditions. Turn slowly while driving on a slope or uneven ground. 
Avoid the cavity, groove, ditch or other obstacles that may cause the   
machine to fall over if any. 
 
[If not] 
Accident may be caused. 

 

Use gangplanks of sufficient length, width and strength for loading/unloading

 

The gangplanks should be firm, secure and provided with anti-skid measures, 
be inclined less than 15 degrees when put on the truck frame, and have   
a length over 4 times of the frame height. 
 
[If not] 
Accident may be caused. 

 

Make sure the ramp boards are parallel and stable while 
 loading/ unloading

 

Be sure to hook the ramp boards stably and reliably in parallel. 
 
[If not] 
The machine may loss balance, fall over and cause injuries. 

Keep  

parallel. 

Stabilize