Content      ..     59      60      61      62     ..

SINUMERIK 840D sl. Service - Configuring Commissioning. Manual (2011-2020) - page 61

NC variables

3.2 NC variable descriptions

numStrokes (C, NIB)

N4

1

Validity:

From NCK version 3.6

Read access

partDistance (C, NIB)

N4

Length of the path between punches

If the block has been divided in segments with the instruction 'SPP' (variable 'automCutSegment' = 2) the variable specifies the

length of the path between the punches.

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

1

Validity:

From NCK version 3.6

Read access

punchActive (C, NIB)

N4

Punching or nibbling active

Identification of punching or nibbling active. The part program turns off/on punching and nibbling with 'SPOF', 'SON' and 'PON'.

Rapid punching and nibbling are turned on/off with 'SONS' and 'PONS'.

The variable 'punchActive' specified the present state.

Return value

0 = inactive

1 = punching active

2 = nibbling active

3 = rapid punching active

4 = rapid nibbling active

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

1

Validity:

From NCK version 3.6

Read access

punchDelayActive (C, NIB)

N4

Punching with delay active

Identifier that indicates whether punching with delay is active. The part program can turn on/off the delay with the instructions

'PDELAYON' and 'PDELAYOF'. The variable 'PunchDelayActive' indicates the present state.

Return value

0 = inactive

1 = active

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

187

NC variables

3.2 NC variable descriptions

punchDelayActive (C, NIB)

N4

Addressing

Line index:

Max. line index:

1

Validity:

From NCK version 3.6

Read access

punchDelayTime (C, NIB)

SD 42400: PUNCH_DWELL_TIME

N4

Punching delay time

Units and value ranges

Physical unit:

Data type:

ms

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

1

Validity:

From NCK version 3.6

Read access

strokeNr (C, NIB)

Current stroke number

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

1

Validity:

From NCK version 3.6

Read access

3.2.3.15

O: Internal

OEM-MMC: LinkItem /Channel/Drive/...

C-O

LOOKAH_NUM_CHECKED_BLOCKS (C, O)

MD 29000: $OC_LOOKAH_NUM_CHE-

CKED_BLOCKS

MD 29000: $OC_LOOKAH_NUM_CHECKED_BLOCKS

Units and value ranges

Physical unit:

Data type:

-

TYPE_DWORD

Read access

NC variables

188

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

3.2.3.16

PA: Protection zones

OEM-MMC: LinkItem /Channel/ProtectedArea/...

Up to 10 protection zones can be defined. Each protection zone is described by a polygon function consisting of up

to 10 elements. The maximum permissible number of protection zones is specified in "$$numProtArea" in the

module Y in area C. The maximum permissible number of polygon definition elements is specified in "$$numCon-

tourInProtArea" in module Y in area C. Module PA contains the individual coordinates of the polygon elements. The

protection zones are addressed via the variable indices.

The classification as NCK or channel-specific protection zone does not affect the protection zone monitoring func-

tion but simply indicates the area in which the protection zone is registered.

The physical unit actually used for length quantities is defined in "$$/C/SGA/extUnit" in module SGA in area C.

MDD_PA_CENT_ABS_0 (C, PA)

$SC_PA_CENT_ABS[x,0] x = Number pro-

A3

tection zone

Abscissa arc centre of 1st contour element

Absolute abscissa value of arc centre of 1st contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ABS_1 (C, PA)

$SC_PA_CENT_ABS[x,1] x = Number pro-

A3

tection zone

Abscissa arc centre of 2nd contour element

Absolute abscissa value of arc centre of 2nd contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ABS_2 (C, PA)

$SC_PA_CENT_ABS[x,2] x = Number pro-

A3

tection zone

Abscissa arc centre of 3rd contour element

Absolute abscissa value of arc centre of 3rd contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

189

NC variables

3.2 NC variable descriptions

MDD_PA_CENT_ABS_2 (C, PA)

$SC_PA_CENT_ABS[x,2] x = Number pro-

A3

tection zone

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ABS_3 (C, PA)

$SC_PA_CENT_ABS[x,3] x = Number pro-

A3

tection zone

Abscissa arc centre of 4th contour element

Absolute abscissa value of arc centre of 4th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ABS_4 (C, PA)

$SC_PA_CENT_ABS[x,4] x = Number pro-

A3

tection zone

Abscissa arc centre of 5th contour element

Absolute abscissa value of arc centre of 5th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ABS_5 (C, PA)

$SC_PA_CENT_ABS[x,5] x = Number pro-

A3

tection zone

Abscissa arc centre of 6th contour element

Absolute abscissa value of arc centre of 6th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

NC variables

190

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

MDD_PA_CENT_ABS_6 (C, PA)

$SC_PA_CENT_ABS[x,6] x = Number pro-

A3

tection zone

Abscissa arc centre of 7th contour element

Absolute abscissa value of arc centre of 7th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ABS_7 (C, PA)

$SC_PA_CENT_ABS[x,7] x = Number pro-

A3

tection zone

Abscissa arc centre of 8th contour element

Absolute abscissa value of arc centre of 8th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ABS_8 (C, PA)

$SC_PA_CENT_ABS[x,8] x = Number pro-

A3

tection zone

Abscissa arc centre of 9th contour element

Absolute abscissa value of arc centre of 9th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ABS_9 (C, PA)

$SC_PA_CENT_ABS[x,9] x = Number pro-

A3

tection zone

Abscissa arc centre of 10th contour element

Absolute abscissa value of arc centre of 10th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

191

NC variables

3.2 NC variable descriptions

MDD_PA_CENT_ABS_9 (C, PA)

$SC_PA_CENT_ABS[x,9] x = Number pro-

A3

tection zone

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ORD_0 (C, PA)

$SC_PA_CENT_ORD[x,0] x = Number pro-

A3

tection zone

Ordinate arc centre of 1st contour element

Absolute ordinate value of arc centre of 1st contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ORD_1 (C, PA)

$SC_PA_CENT_ORD[x,1] x = Number pro-

A3

tection zone

Ordinate arc centre of 2nd contour element

Absolute ordinate value of arc centre of 2nd contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ORD_2 (C, PA)

$SC_PA_CENT_ORD[x,2] x = Number pro-

A3

tection zone

Odinate arc centre of 3rd contour element

Absolute ordinate value of arc centre of 3rd contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

NC variables

192

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

MDD_PA_CENT_ORD_3 (C, PA)

$SC_PA_CENT_ORD[x,3] x = Number pro-

A3

tection zone

Ordinate arc centre of 4th contour element

Absolute ordinate value of arc centre of 4th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ORD_4 (C, PA)

$SC_PA_CENT_ORD[x,4] x = Number pro-

A3

tection zone

Ordinate arc centre of 5th contour element

Absolute ordinate value of arc centre of 5th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ORD_5 (C, PA)

$SC_PA_CENT_ORD[x,5] x = Number pro-

A3

tection zone

Ordinate arc centre of 6th contour element

Absolute ordinate value of arc centre of 6th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ORD_6 (C, PA)

$SC_PA_CENT_ORD[x,6] x = Number pro-

A3

tection zone

Ordinate arc centre of 7th contour element

Absolute ordinate value of arc centre of 7th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

193

NC variables

3.2 NC variable descriptions

MDD_PA_CENT_ORD_6 (C, PA)

$SC_PA_CENT_ORD[x,6] x = Number pro-

A3

tection zone

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ORD_7 (C, PA)

$SC_PA_CENT_ORD[x,7] x = Number pro-

A3

tection zone

Ordinate arc centre of 8th contour element

Absolute ordinate value of arc centre of 8th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ORD_8 (C, PA)

$SC_PA_CENT_ORD[x,8] x = Number pro-

A3

tection zone

Ordinate arc centre of 9th contour element

Absolute ordinate value of arc centre of 9th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CENT_ORD_9 (C, PA)

$SC_PA_CENT_ORD[x,9] x = Number pro-

A3

tection zone

Ordinate arc centre of 10th contour element

Absolute ordinate value of arc centre of 10th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

NC variables

194

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

MDD_PA_CONT_ABS_0 (C, PA)

$SC_PA_CONT_ABS[x,0] x = Number pro-

A3

tection zone

Abscissa end point of 1st contour element

Absolute abscissa value of end point of 1st contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ABS_1 (C, PA)

$SC_PA_CONT_ABS[x,1] x = Number pro-

A3

tection zone

Abscissa end point of 2nd contour element

Absolute abscissa value of end point of 2nd contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ABS_2 (C, PA)

$SC_PA_CONT_ABS[x,2] x = Number pro-

A3

tection zone

Abscissa end point of 3rd contour element

Absolute abscissa value of end point of 3rd contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ABS_3 (C, PA)

$SC_PA_CONT_ABS[x,3] x = Number pro-

A3

tection zone

Abscissa end point of 4th contour element

Absolute abscissa value of end point of 4th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

195

NC variables

3.2 NC variable descriptions

MDD_PA_CONT_ABS_3 (C, PA)

$SC_PA_CONT_ABS[x,3] x = Number pro-

A3

tection zone

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ABS_4 (C, PA)

$SC_PA_CONT_ABS[x,4] x = Number pro-

A3

tection zone

Abscissa end point of 5th contour element

Absolute abscissa value of end point of 5th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ABS_5 (C, PA)

$SC_PA_CONT_ABS[x,5] x = Number pro-

A3

tection zone

Abscissa end point of 6th contour element

Absolute abscissa value of end point of 6th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ABS_6 (C, PA)

$SC_PA_CONT_ABS[x,6] x = Number pro-

A3

tection zone

Abscissa end point of 7th contour element

Absolute abscissa value of end point of 7th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

NC variables

196

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

MDD_PA_CONT_ABS_7 (C, PA)

$SC_PA_CONT_ABS[x,7] x = Number pro-

A3

tection zone

Abscissa end point of 8th contour element

Absolute abscissa value of end point of 8th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ABS_8 (C, PA)

$SC_PA_CONT_ABS[x,8] x = Number pro-

A3

tection zone

Abscissa end point of 9th contour element

Absolute abscissa value of end point of 9th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ABS_9 (C, PA)

$SC_PA_CONT_ABS[x,9] x = Number pro-

A3

tection zone

Abscissa end point of 10th contour element

Absolute abscissa value of end point of 10th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ORD_0 (C, PA)

$SC_PA_CONT_ORD[x,0] x = Number pro-

A3

tection zone

Ordinate end point of 1st contour element

Absolute ordinate value of end point of 1st contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

197

NC variables

3.2 NC variable descriptions

MDD_PA_CONT_ORD_0 (C, PA)

$SC_PA_CONT_ORD[x,0] x = Number pro-

A3

tection zone

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ORD_1 (C, PA)

$SC_PA_CONT_ORD[x,1] x = Number pro-

A3

tection zone

Ordinate end point of 2nd contour element

Absolute ordinate value of end point of 2nd contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ORD_2 (C, PA)

$SC_PA_CONT_ORD[x,2] x = Number pro-

A3

tection zone

Odinate end point of 3rd contour element

Absolute ordinate value of end point of 3rd contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ORD_3 (C, PA)

$SC_PA_CONT_ORD[x,3] x = Number pro-

A3

tection zone

Ordinate end point of 4th contour element

Absolute ordinate value of end point of 4th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

NC variables

198

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

MDD_PA_CONT_ORD_4 (C, PA)

$SC_PA_CONT_ORD[x,4] x = Number pro-

A3

tection zone

Ordinate end point of 5th contour element

Absolute ordinate value of end point of 5th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ORD_5 (C, PA)

$SC_PA_CONT_ORD[x,5] x = Number pro-

A3

tection zone

Ordinate end point of 6th contour element

Absolute ordinate value of end point of 6th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ORD_6 (C, PA)

$SC_PA_CONT_ORD[x,6] x = Number pro-

A3

tection zone

Ordinate end point of 7th contour element

Absolute ordinate value of end point of 7th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ORD_7 (C, PA)

$SC_PA_CONT_ORD[x,7] x = Number pro-

A3

tection zone

Ordinate end point of 8th contour element

Absolute ordinate value of end point of 8th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

199

NC variables

3.2 NC variable descriptions

MDD_PA_CONT_ORD_7 (C, PA)

$SC_PA_CONT_ORD[x,7] x = Number pro-

A3

tection zone

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ORD_8 (C, PA)

$SC_PA_CONT_ORD[x,8] x = Number pro-

A3

tection zone

Ordinate end point of 9th contour element

Absolute ordinate value of end point of 9th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_CONT_ORD_9 (C, PA)

$SC_PA_CONT_ORD[x,9] x = Number pro-

A3

tection zone

Ordinate end point of 10th contour element

Absolute ordinate value of end point of 10th contour element

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDD_PA_MINUS_LIM (C, PA)

$SC_PA_MINUS_LIM[x] x = Number pro-

A3

tection zone

Lower limit of protection zone, applicate

Limitation in the minus direction of the protection zone in the axis that is perpendicular to the polygon definition (applicate)

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

NC variables

200

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

MDD_PA_PLUS_LIM (C, PA)

$SC_PA_PLUS_LIM[x] x = Number protec-

A3

tion zone

Upper boundary of protection zone, applicate

Limitation of the protection zone in the plus direction of the axis that is perpendicular to the polygon definition (applicate)

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_ACTIV_IMMED (C, PA)

$SC_PA_ACTIV_IMMED[x] x = Number

A3

protection zone

Active immediately after referencing

Code for "active immediately after referencing", i.e. the protection zone is active as soon as the control has been started up and

the axes have been referenced

Return value

0 = protection zone is not active immediately

1 = protection zone is active immediately

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_NUM (C, PA)

$SC_PA_CONT_NUM[x] x = Number pro-

A3

tection zone

Number of valid contour elements

Units and value ranges

Physical unit:

Data type:

Minimum value:

Maximum value:

-

TYPE_UWORD

0

$$numContourInProtArea

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_TYP_0 (C, PA)

$SC_PA_CONT_TYP[x,0] x = Number pro-

A3

tection zone

Contour type of 1st contour element

Return value

0 = G1

1 = G2

2 = G3

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

201

NC variables

3.2 NC variable descriptions

MDU_PA_CONT_TYP_0 (C, PA)

$SC_PA_CONT_TYP[x,0] x = Number pro-

A3

tection zone

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_TYP_1 (C, PA)

$SC_PA_CONT_TYP[x,1] x = Number pro-

A3

tection zone

Contour type of 2nd contour element

Return value

0 = G1

1 = G2

2 = G3

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_TYP_2 (C, PA)

$SC_PA_CONT_TYP[x,2] x = Number pro-

A3

tection zone

Contour type of 3rd contour element

Return value

0 = G1

1 = G2

2 = G3

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_TYP_3 (C, PA)

$SC_PA_CONT_TYP[x,3] x = Number pro-

A3

tection zone

Contour type of 4th contour element

Return value

0 = G1

1 = G2

2 = G3

NC variables

202

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

MDU_PA_CONT_TYP_3 (C, PA)

$SC_PA_CONT_TYP[x,3] x = Number pro-

A3

tection zone

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_TYP_4 (C, PA)

$SC_PA_CONT_TYP[x,4] x = Number pro-

A3

tection zone

Contour type of 5th contour element

Return value

0 = G1

1 = G2

2 = G3

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_TYP_5 (C, PA)

$SC_PA_CONT_TYP[x,5] x = Number pro-

A3

tection zone

Contour type of 6th contour element

Return value

0 = G1

1 = G2

2 = G3

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_TYP_6 (C, PA)

$SC_PA_CONT_TYP[x,6] x = Number pro-

A3

tection zone

Contour type of 7th contour element

Return value

0 = G1

1 = G2

2 = G3

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

203

NC variables

3.2 NC variable descriptions

MDU_PA_CONT_TYP_6 (C, PA)

$SC_PA_CONT_TYP[x,6] x = Number pro-

A3

tection zone

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_TYP_7 (C, PA)

$SC_PA_CONT_TYP[x,7] x = Number pro-

A3

tection zone

Contour type of 8th contour element

Return value

0 = G1

1 = G2

2 = G3

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_TYP_8 (C, PA)

$SC_PA_CONT_TYP[x,8] x = Number pro-

A3

tection zone

Contour type of 9th contour element

Return value

0 = G1

1 = G2

2 = G3

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_CONT_TYP_9 (C, PA)

$SC_PA_CONT_TYP[x,9] x = Number pro-

A3

tection zone

Contour type of 10th contour element

Return value

0 = G1

1 = G2

2 = G3

NC variables

204

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

MDU_PA_CONT_TYP_9 (C, PA)

$SC_PA_CONT_TYP[x,9] x = Number pro-

A3

tection zone

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_LIM_3DIM (C, PA)

$SC_PA_LIM_3DIM[x] x = Number pro-

A3

tection zone

Limitation of protection zone applicate

Code for limitation of protection zone in the axis that is perpendicular to polygon definition (applicate)

Return value

0 = no limitation

1 = limitation in positive direction

2 = limitation in negative direction

3 = limitation in both directions

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

MDU_PA_ORI (C, PA)

$SC_PA_ORI[x] x = Number protection

A3

zone

Plane assignment of protection zone

Code for plane assignment of protection zone

Return value

0 = G17

1 = G18

2 = G19

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

205

NC variables

3.2 NC variable descriptions

MDU_PA_TW (C, PA)

$SC_PA_T_W[x] x = Number protection

A3

zone

Workpiece or tool-related protection zone

Code for workpiece or tool-oriented protection zone

Return value

0 = workpiece-related

1 = reserved

2 = reserved

3 = tool-related

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

$$numProtArea

Validity:

From NCK version 3.6

Read access

collisionAlarm (C, PA)

OD19830 $ON_COLLISION_MASK

Collision of two protection zones

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

3

Read access

acCollPos (C, PA)

Collision position in world coordinates

Contact point between two collision bodies during a collision alarm.

Corresponds with system variable $AC_COLLPOS

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

3

Read access

declarProtObject (C, PA)

Declaration of a variable protection zone

Return value

0=No object

1=WORKPIECE

2=FIXTURE

NC variables

206

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

fixtureStatus (C, PA)

Units and value ranges

Physical unit:

Data type:

-

TYPE_WORD

Read access

3.2.3.17

RP: Arithmetic parameter

OEM-MMC: LinkItem /Channel/Parameter/...

Arithmetic parameters are special predefined variables which are addressed with the letter R followed by a number.

The contents and meaning of an arithmetic parameter are defined by the programmer of a part program. 100 R

variables are defined by default. The number of R variables can be set via machine data 28050 (MM_NUM_R_PA-

RAM).

rpa (C, RP)

$R[x] x = ParameterNo

PA

Alternative name:

R

R variables

Units and value ranges

Physical unit:

Data type:

-

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

MM_NUM_R_PARAM + 1

Validity:

From NCK version 3.6

Read access and write access

3.2.3.18

S: State data

OEM-MMC: LinkItem /Channel/State/...

During NC operation different internal states occur and system-specific data may change during operation. To

distinguish those from system variables, they are classified as state data.

A distinction is made between:

- NCK-specific state data

- Mode-group-specific state data

- Channel-specific state data

- Drive-specific state data (FDD)

- Drive-specific state data (MSD)

NC variables

208

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

G0Mode (C, S)

$AC_G0MODE

G00: Path axes traverse as pos. axes

G00 is active and $MC_G0_LINEAR_MODE is FALSE (Siemens mode) or $MC_EXTERN_G0_LINEAR_MODE is FALSE (ISO mode)

and therefore non-linear interpolation is active with G0, i.e. the path axes are traversed as positioning axes.

Return value

0: G00 not active

1: G00 and linear interpolation active

2: G00 and non-linear interpolation active

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

0

0

2

Addressing

Line index:

Max. line index:

1

Read access

aGG (C, S)

$A_GG

active G function in synchronized action

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

-

TYPE_UWORD

0

0

Addressing

Line index:

Max. line index:

$$/N/YNCFL/Gruppe_NUM

Read access

aLinkTransRate (C, S)

$A_LINK_TRANS_RATE

Link transfer rate

Link transfer rate

Number of link variables that can still be transferred in the

current IPO cycle via the NCU link communication.

If this variable is read in the context of the lead, it always

outputs the maximum available bandwidth.

Units and value ranges

Physical unit:

Data type:

Minimum value:

-

TYPE_UWORD

0

Addressing

Line index:

Max. line index:

1

Read access

aMonifact (C, S)

$A_MONIFACT

Factor for tool life monitoring

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

209

NC variables

3.2 NC variable descriptions

aTcMtn (C, S)

$AC_TC_MTN

Target magazine new tool

Target magazine number of new tool

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

1

Read access

aTcMto (C, S)

$AC_TC_MTO

Target magazine old tool

Target magazine number of old tool

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

1

Read access

aTcStatus (C, S)

$AC_TC_STATUS

Command status

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

1

Read access

aTcThno (C, S)

$AC_TC_THNO

Number of toolholder

Number of toolholder for new tool

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

1

Read access

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

213

NC variables

3.2 NC variable descriptions

aTcMtptn (C, S)

$AC_TC_MTLTN

Number of the multitool place of the tool

Number of the multitool place of the loaded tool

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

1

Read access

aTcNumPlaces (C, S)

$AC_TC_MTNLOC

Number of defined places in the multitool

Units and value ranges

Physical unit:

Data type:

-

TYPE_UWORD

Addressing

Line index:

Max. line index:

1

Read access

aaAccLim (C, S)

Axial acceleration override (ACC)

Display of the axial acceleration override programmed by ACC.

Depending on $MA_DYN_LIMIT_RESET_MASK, the value can remain active after Reset.

The variable always shows the programmed acceleration override and not the currently active acceleration limit.

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

100

1

200

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access

aaAccLimA (C, S)

$AA_ACCLIMA[a]

Axial acceleration overr. main run

Axial acceleration override in main run

Return value

1-200

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

100

1

200

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

215

NC variables

3.2 NC variable descriptions

aaAccLimA (C, S)

$AA_ACCLIMA[a]

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access

aaJerkLim (C, S)

Axial jerk override (JERKLIM)

Display of the axial jerk override programmed by JERKLIM.

Depending on $MA_DYN_LIMIT_RESET_MASK, the value can remain active after Reset.

The variable always shows the programmed jerk override and not the currently active jerk limit.

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

100

1

200

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access

aaVeloLim (C, S)

Axial velocity override (VELOLIM)

Display of the axial velocity override programmed by VELOLIM.

Depending on $MA_DYN_LIMIT_RESET_MASK, the value can remain active after Reset.

The variable always shows the programmed velocity override and not the currently active velocity limit.

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

100

1

200

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access

NC variables

216

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

actCollPosMcsPacked (C, S)

Collision position in MCS

Position of a channel axis with a collision in the MCS.

The positions can be read for all configured channel axes.

Row index corresponds to

1 1st configured channel axis

2 2nd configured channel axis

20

20th configured channel axis

Units and value ranges

Physical unit:

Data type:

Initial value

mm, inch, degree, user defi-

TYPE_DOUBLE

0

ned

Addressing

Line index:

Max. line index:

MAXNUM_AXES_PER_CHAN

Read access

aaEgActive (C, S)

$AA_EG_ACTIVE[a,b]

EG link active

Electronic gear:

Link to the specified master axis is operative, i.e. activated.

Return value

0: Deactivated

1: Activated

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

0

0

1

Addressing

Line index:

Max. line index:

$$numMachAxes * $$numMachAxes

Read access

aaEgAx (C, S)

$AA_EG_AX[n,a]

EG axis number master axis

Electronic gear:

Axis number of nth master axis (1-n).

(Axis index = axis number - 1)

Return value

1-numMachAxes

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

0

1

$$numMachAxes

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

217

NC variables

3.2 NC variable descriptions

aaEgAx (C, S)

$AA_EG_AX[n,a]

Addressing

Line index:

Max. line index:

$$numMachAxes * 5

Read access

aaEgDenom (C, S)

$AA_EG_DENOM[a,b]

EG denominator link factor

Electronic gear:

Denominator of link factor for the specified master axis.

The link factor of the gear is the result of $AA_EG_NUMERA[a,b]/$AA_EG_DENOM[a,b].

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

1

Addressing

Line index:

Max. line index:

$$numMachAxes * $$numMachAxes

Read access

aaEgNumLa (C, S)

$AA_EG_NUM_LA[a]

EG number of master axes

Electronic gear:

Number of master axes specified with EGDEF.

If the axis has not been specified with EGDEF as slave axis,

the value is 0.

Return value

0-5

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

0

0

5

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access

aaEgNumera (C, S)

$AA_EG_NUMERA[a,b]

EG numerator link factor

Electronic gear:

Numerator of link factor for the specified master axis.

The link factor of the gear is the result of $AA_EG_NUMERA[a,b]/$AA_EG_DENOM[a,b].

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

NC variables

218

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

aaEgNumera (C, S)

$AA_EG_NUMERA[a,b]

$$numMachAxes * $$numMachAxes

Read access

aaEgSyn (C, S)

$AA_EG_SYN[a,b]

EG synchronous position of master axis

Electronic gear:

Synchronous position for the specified master axis.

Units and value ranges

Physical unit:

Data type:

Initial value

mm, inch, degree, user defi-

TYPE_DOUBLE

0

ned

Addressing

Line index:

Max. line index:

$$numMachAxes * $$numMachAxes

Read access

aaEgSynFa (C, S)

$AA_EG_SYNFA[a]

EG synchronous position of slave axis

Electronic gear:

Synchronous position for the slave axis.

Units and value ranges

Physical unit:

Data type:

Initial value

mm, inch, degree, user defi-

TYPE_DOUBLE

0

ned

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access

aaEgType (C, S)

$AA_EG_TYPE[a,b]

EG link type

Electronic gear:

Type of link for the specified master axis

Return value

0: Actual-value linkage

1: Setpoint linkage

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

0

0

1

Addressing

Line index:

Max. line index:

$$numMachAxes * $$numMachAxes

Read access

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

219

NC variables

3.2 NC variable descriptions

aaJerkLimA (C, S)

$AA_JERKLIMA[a]

Axial jerk override main run

Axial jerk override in run in

Return value

1-200

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

100

1

200

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access

aaMeasP1Valid (C, S)

$AA_MEAS_P1_VALID

Save axial measuring point 1

Save axial measuring point P1 for workpiece and

tool measurement

Return value

0: Clear axial measuring point

1: Write actual axial values to axial measuring point

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_DWORD

0

0

1

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access and write access

aaMeasP2Valid (C, S)

$AA_MEAS_P2_VALID

Save axial measuring point 2

Save axial measuring point P2 for workpiece and

tool measurement

Return value

0: Clear axial measuring point

1: Write actual axial values to axial measuring point

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_DWORD

0

0

1

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access and write access

NC variables

220

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

aaMeasP3Valid (C, S)

$AA_MEAS_P3_VALID

Save axial measuring point 3

Save axial measuring point P3 for workpiece and

tool measurement

Return value

0: Clear axial measuring point

1: Write actual axial values to axial measuring point

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_DWORD

0

0

1

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access and write access

aaMeasP4Valid (C, S)

$AA_MEAS_P4_VALID

Save axial measuring point 4

Save axial measuring point P4 for workpiece and

tool measurement

Return value

0: Clear axial measuring point

1: Write actual axial values to axial measuring point

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_DWORD

0

0

1

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access and write access

aaMeasPoint1 (C, S)

$AA_MEAS_POINT1

1st measuring point

1st measuring point for workpiece and tool measurement

Units and value ranges

Physical unit:

Data type:

Initial value

mm, inch, user defined

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access and write access

aaMeasPoint2 (C, S)

$AA_MEAS_POINT2

2nd measuring point

2nd measuring point for workpiece and tool measurement

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

221

NC variables

3.2 NC variable descriptions

aaMeasSetpoint (C, S)

$AA_MEAS_SETPOINT

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access and write access

aaMeasSpValid (C, S)

$AA_MEAS_SP_VALID

Save axial setpoint

Save axial setpoint for workpiece and

tool measurement

Return value

0: Clear axial setpoint

1: Validate axial setpoint

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_DWORD

0

0

1

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access and write access

aaVeloLimA (C, S)

$AA_VELOLIMA[a]

Axial velocity overr. main run

Axial velocity override in main run

Return value

1-200

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

100

1

200

Addressing

Line index:

Max. line index:

$$numMachAxes

Read access

acAlarmStat (C, S)

$AC_ALARM_STAT

ESR alarm status

!=0: Alarms are pending, the appropriate coded alarm reactions can be used as source for

"Extended stop and retract".

Return value

The data is bit-coded. Individual states can therefore be masked or

evaluated separately if necessary (bits excluded below produce a value of 0)

Bit2 = 1: NOREADY (active rapid deceleration + cancellation of servo enable)

Bit6 = 1: STOPBYALARM (ramp stop of all channel axes)

Bit9 = 1: SETVDI (VDI interface signal alarm setting)

Bit13 = 1: FOLLOWUPBYALARM (follow-up)

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

223

NC variables

3.2 NC variable descriptions

acAlarmStat (C, S)

$AC_ALARM_STAT

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_UWORD

0

Addressing

Line index:

Max. line index:

1

Read access

acAsup (C, S)

$AC_ASUP

Reason for the activation of an ASUB

Code number for the cause of activation of an ASUB

Return value

The reasons are bit-coded.

BIT0: Activation because of: User interrupt "ASUB with Blsync".

BIT1: Activation because of: User interrupt "ASUB".

BIT2: Activation because of: User interrupt "ASUB from channel state Ready".

BIT3: Activation because of: User interrupt "ASUB in manual mode".

BIT4: Activation because of: Activation because of: User interrupt "ASUB".

BIT5: Activation because of: Abort of the subroutine repetition.

BIT6: Activation because of: Activation of decoding single block.

BIT7: Activation because of: Activation of DDTG.

BIT8: Activation because of: Activation of axis synchronization.

BIT9: Activation because of: Change of operating mode.

BIT10: Activation because of: Program continuation under TeachIn or after TeachIn deactivation.

BIT11: Activation because of: Selection overstore.

BIT12: Activation because of: Alarm with reaction compensation block with REPOS ( COMPB-

LOCKWITHREORG).

BIT13: Activation because of: Retraction motion with G33 and Stop.

BIT14: Activation because of: Activation of dry run feed.

BIT15: Activation because of: Deactivation of dry run feed.

BIT16: Activation because of: Activation of skip block.

BIT17: Activation because of: Deactivation of skip block.

BIT18: Activation because of: Activate machine data.

BIT19: Activation because of: Activate tool offset.

BIT20: Activation because of: System ASUB after search type SERUPRO has reached the search

target.

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

-

TYPE_DWORD

0

0

Addressing

Line index:

Max. line index:

1

Read access

NC variables

224

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

acAxCtSwA (C, S)

$AC_AXCTSWA[CTn]

Status of axis container

Channel status of axis container rotation

Return value

TRUE: The channel has enabled rotation for the axis container

and rotation is still in progress.

FALSE: Axis container rotation is already finished

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

0

0

1

Addressing

Line index:

Max. line index:

$$numContainer

Read access

acConeAngle (C, S)

$AC_CONE_ANGLE

Taper angle

Currently effective taper angle for taper turning.

The taper angle is specified by the setting data $SC_CONE_ANGLE and is

effective in the operating mode JOG only.

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

Degree

TYPE_DOUBLE

0

-90

90

Addressing

Line index:

Max. line index:

1

Read access

acDelt (C, S)

$AC_DELT

Stored distance-to-go of the path in the WCS

Stored distance-to-go of the path in the WCS after delete-distance-to-go of the path DELDTG for synchronous action (Note: for

SYNACT only)

Units and value ranges

Physical unit:

Data type:

-

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

1

Read access

acDtbb (C, S)

$AC_DTBB

Distance from beginning of the block in the BCS

Distance from the beginning of the block in the BCS (Note: SYNACT only)

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

225

NC variables

3.2 NC variable descriptions

actToolDataBeforeSearch (C, S)

$P_

_BEFORE_SEARCH_RUN

Active tool offset data before the search

Data for determining the active tool offset before the search, that is in reset status before the start of the search.

After reaching the search target, the value is set to the current value for each programming of master tool holder, spindle, D

no or DL no.

-P1: Master tool holder or spindle before the search ($AC_MTHNUM_BEFORE_SEARCH)

Programming "MTH(no)" or "MS(no)" after reaching the search target, this variable then returns the same value as

acMthNum.

-P2: Active D no. before the search (see $P_D_BEFORE_SEARCH)

Programming "D" after reaching the search target, this variable then returns the same value as actDNumber.

-P3: Active DL no. before the search (see $P_DL_BEFORE_SEARCH)

Programming "DL" after reaching the search target, this variable then returns the same value as actDLNumber.

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

-

TYPE_UWORD

0

0

Addressing

Line index:

Max. line index:

$$numSearchRunToolParams

Read access

NC variables

228

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

acsAxFrame (C, S)

Current axial ACS frame

The variable acsAxFrame returns the axial frames of the active ACS (SZS) frames.

The variable has the following structure:

Row index Description

1 - 2

Frame for the 1st channel axis

3 - 4

Frame for the 2nd channel axis

5 - 6

Frame for the 3rd channel axis

7 - 8

Frame for the 4th channel axis

9 - 10

Frame for the 5th channel axis

39 - 40

Frame for the 20th channel axis

The axial frame consists of two values:

Double axSumTrans

Double axScale

For example, to read the first five channel axes, the row index must be entered as = 1 and the maximum row index as 10 ( 5 *

2 ).

The axial frames are returned for all configured channel axes without any axis gaps.

Note:

axSumTrans: Total translation

axScale: Scaling. In the event of a negative value, the axis is mirrored.

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

40

Read access

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

229

NC variables

3.2 NC variable descriptions

acsGeoFrame (C, S)

Current ACS contour frame

The variable acsGeoFrame returns the current ACS contour frame.

The variable has the following structure:

Row index Description

1 - 3

Double geoSumTrans[GEODIM]

4 - 6

Double geoScale[GEODIM]

7 - 9

Double geoRot[GEODIM]

10 - 12

Double geoShear[GEODIM]

The maximum row index entered specifies how many values are to be read at any one time.

Example: Row index = 1 and the maximum index = 12: This enables the complete contour frame to be read (12 values).

Note:

GEODIM:

3 (number of geometry axes)

geoSumTrans: Total translation of the 1st to the 3rd geometry axis

geoScale: Scaling of the 1st to the 3rd geometry axis. In the event of a negative value, the axis is mirrored.

geoRot:

Rotation around the 1st to the 3rd geometry axis. The MD has to determine whether the notation is RPY or Euler.

geoShear: Shear angle of the 1st to the 3rd geometry axis (the shear angle is 90 degrees in orthonormal coordinate systems)

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

12

Read access

actOriToolLengthENS (C, S)

X, Y, Z tool components in the SZS

X, Y, Z components in the SZS of the active tool length, taking into account the tool orientation, including adapter data,

mirrorings and TCARR

(orientable tool carrier).

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

3

Read access

NC variables

230

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

actToolBasePosMcsPacked (C, S)

Position of the tool holder in the MCS

Position of a channel axis in the MCS with reference to the tool holder.

The positions can be read for all configured channel axes without any axis gaps.

Row index Corresponds to

1

1st configured channel axis

2

2nd configured channel axis

20

20th configured channel axis

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

MAXNUM_AXES_PER_CHAN

Read access

actToolEdgeCenterPosBcsPacked (C, S)

Position of the edge center in the BCS

Position of a channel axis in the BCS with reference to the edge center.

The positions can be read for all configured channel axes without any axis gaps.

Row index Corresponds to

1

1st configured channel axis

2

2nd configured channel axis

20

20th configured channel axis

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

MAXNUM_AXES_PER_CHAN

Read access

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

231

NC variables

3.2 NC variable descriptions

actToolEdgeCenterPosEnsPacked (C, S)

Position of the edge center in the SZS

Position of a channel axis in the SZS coordinate system with reference to the edge center.

The positions can be read for all configured channel axes without any axis gaps.

Row index Corresponds to

1

1st configured channel axis

2

2nd configured channel axis

20

20th configured channel axis

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

MAXNUM_AXES_PER_CHAN

Read access

actToolEdgeCenterPosEnsPathn1 (C, S)

Position of the TCP in the SZS

TCP SZS positions of the path axes with path parameter = 1. Packed for all configured channel axes (without gaps).

The positions do not have to correspond to the programmed positions (TRC, WAB, etc.)

The positions can be read for all configured channel axes without any axis gaps.

Row index Corresponds to

1

1st configured channel axis

2

2nd configured channel axis

20

20th configured channel axis

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

MAXNUM_AXES_PER_CHAN

Read access

NC variables

232

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

cmdToolEdgeCenterPosBcsPathn1 (C, S)

End position of the TCP in the BCS

TCP BCS positions of the path axes with path parameter = 1. Packed for all configured channel axes (without gaps).

The positions do not have to correspond to the programmed positions (TRC, WAB, etc.)

The positions can be read for all configured channel axes without any axis gaps.

Row index Corresponds to

1

1st configured channel axis

2

2nd configured channel axis

20

20th configured channel axis

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

MAXNUM_AXES_PER_CHAN

Read access

cmdToolEdgeCenterPosMcsPathn1 (C, S)

Position of the TCP in the MCS

TCP MCS positions of the path axes with path parameter = 1. Packed for all configured channel axes (without gaps).

The positions do not have to correspond to the programmed positions (TRC, WAB, etc.)

The positions can be read for all configured channel axes without any axis gaps.

Row index Corresponds to

1

1st configured channel axis

2

2nd configured channel axis

20

20th configured channel axis

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

MAXNUM_AXES_PER_CHAN

Read access

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

233

NC variables

3.2 NC variable descriptions

auxfu (C, S)

Current auxiliary function

The variable is only used to read the auxiliary function during the output to the PLC.

This variable may only be used with the event AUXFU.

The variable has the following structure:

Double auxFuType;

Double extension;

Double value;

auxFuType is an integer value and can return the following values:

0: GARBAGE

1: M

2: M (generated by system)

3: H

4: S

5: S (generated by system)

6: T

7: D

8: DL

9: F

Value : floating point with S / F / H ($MC_AUXFU_H_TYPE_INT = 0)

Integer value with M / T / D / DL / H ($MC_AUXFU_H_TYPE_INT = 1)

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

3

Read access

NC variables

234

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

axesActiveInChan (C, S)

Bit mask of all active axes in the channel

Bit mask of all active axes in the channel.

There are many types of axes, e.g. geometry axis, positioning axis, command axis, PLC axis etc. In this mask, only those axes

are marked which, in principle, can be interpolated by an interpolator in this channel.

Bit Description

0

1. Channel axis

1

2. Channel axis

20

20. Channel axis

Units and value ranges

Physical unit:

Data type:

-

TYPE_UDWORD

Addressing

Line index:

Max. line index:

1

Read access

blockProgInfo (C, S)

$AC_BLOCK_PROGSTATE

Information of active block in the interpolator

Returns the information of a main run block.

Return value

Bit-coded:

Bit 0: Block is end of main program ( M02, M17, M30 or RET(ASUB) )

Bit 1: Block is end of subprogram

Bit 2: Block is last initializing block

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

-

TYPE_DWORD

0

0

Addressing

Line index:

Max. line index:

1

Read access

chanAxesIpoAtEnd (C, S)

Channel axis has reached the end of its movement

Bit field of channel axes have reached their end of movement.

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_UDWORD

0

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

235

NC variables

3.2 NC variable descriptions

chanAxesIpoAtEnd (C, S)

Addressing

Line index:

Max. line index:

1

Read access

speedCtrlSpindlesMask (C, S)

Speed-controlled spindles in the channel

Bit array of the speed-controlled spindles of a channel.

If axes in the channel are defined with N20070 $MC_AXCONF_MACHAX_USED[n], speedCtrlSpindlesMask indicates all the

speed-controlled spindles.

For example, if 6 axes are defined in the channel, and axes 4 and 5 are spindles, speedCtrlSpindlesMask returns the 0x18.

Any gaps in the bit array, e.g. if axis 3 is not defined, are closed in the mask.

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_UDWORD

0

Addressing

Line index:

Max. line index:

1

Read access

cmdTrafoParS (C, S)

$P_TRAFO_PAR[n]

Parameter(s) of the programmed transformation

Supplies the value of parameter 'n' of the programmed transformation, e.g. the cylinder diameter in the case of TRACYL

Units and value ranges

Physical unit:

Data type:

-

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

8

Read access

acDtew (C, S)

$AC_DTEW

Distance to the end of the block in the WCS

Distance to the end of the block in the WCS

(Note: for SYNACT only)

Units and value ranges

Physical unit:

Data type:

-

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

1

Read access

NC variables

236

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

acEsrTrigger (C, S)

$AC_ESR_TRIGGER

Activation of ESR

Activation of "NC-controlled ESR"

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

0

0

1

Addressing

Line index:

Max. line index:

1

Read access

acFGo (C, S)

$AC_F_G0

Max. rapid traverse rate in the block

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

mm/min, inch/min, user de-

TYPE_DOUBLE

0

0

fined

Addressing

Line index:

Max. line index:

1

Read access

acFct0 (C, S)

$AC_FCT0[x] x = PolynomNo

a0-coeff. nth polynominal for synchonous action

a0-coefficient of the nth polynominal for the synchronous action SYNFCT / function FCTDEF n

(Note: for SYNACT only)

Units and value ranges

Physical unit:

Data type:

-

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$MC_MM_NUM_FCTDEF_ELEMENTS

Read access

acFct1 (C, S)

$AC_FCT1[x] x = PolynomNo

a1-coeff. nth polynominal for synchonous action

a1-coefficient of the nth polynominal for the synchronous action SYNFCT / function FCTDEF n

(Note: for SYNACT only)

Units and value ranges

Physical unit:

Data type:

-

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

237

NC variables

3.2 NC variable descriptions

acFct1 (C, S)

$AC_FCT1[x] x = PolynomNo

$MC_MM_NUM_FCTDEF_ELEMENTS

Read access

acFct2 (C, S)

$AC_FCT2[x] x = PolynomNo

a2-coeff. nth polynominal for synchonous action

a2-coefficient of the nth polynominal for the synchronous action

SYNFCT / function FCTDEF n

(Note: for SYNACT only)

Units and value ranges

Physical unit:

Data type:

-

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$MC_MM_NUM_FCTDEF_ELEMENTS

Read access

acFct3 (C, S)

$AC_FCT3[x] x = PolynomNo

a3-coeff. nth polynominal for synchonous action

a3-coefficient of the nth polynominal for the synchronous action

SYNFCT / function FCTDEF n

(Note: for SYNACT only)

Units and value ranges

Physical unit:

Data type:

-

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$MC_MM_NUM_FCTDEF_ELEMENTS

Read access

acFctll (C, S)

$AC_FCTLL[x] x = PolynomNo

Lower limit nth polynominal for synchronous action

Lower limit of the nth polynominal for the synchronous action SYNFCT / function FCTDEF n

(Note: for SYNACT only)

Units and value ranges

Physical unit:

Data type:

-

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$MC_MM_NUM_FCTDEF_ELEMENTS

Read access

NC variables

238

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

acFctul (C, S)

$AC_FCTUL[x] x = PolynomNo

Upper limit nth polynominal for synchronous action

Upper limit of the nth polynominal for the synchronous action SYNFCT / function FCTDEF n

(Note: for SYNACT only)

Units and value ranges

Physical unit:

Data type:

-

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

$MC_MM_NUM_FCTDEF_ELEMENTS

Read access

acIwStat (C, S)

$AC_IW_STAT

Current position of machine

Return value

Bit-coded:

Bit 0: Tool inv. position

Bit 1: Axis 2/3 position

Bit 2: Axis 5 position

Bit 3-31: Not yet assigned

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DWORD

0

Addressing

Line index:

Max. line index:

1

Read access

acIwTu (C, S)

$AC_IW_TU

Current position of channel axes

Return value

Bit-coded:

Bit 0: Channel axis 1 position

Bit 1: Channel axis 2 position

Bit 2: Channel axis 3 position

Bit 3: Channel axis 4 position

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DWORD

0

Addressing

Line index:

Max. line index:

1

Read access

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

239

NC variables

3.2 NC variable descriptions

acJogCoord (C, S)

$AC_JOG_COORD

Coordinate system manual travel

Setting the coordinate system for the manual travel

Return value

0: Work

1: SZS

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_DWORD

0

0

1

Read access and write access

acLiftFast (C, S)

$AC_LIFTFAST

Information about LIFTFAST

Information about the execution of LIFTFAST.

At the start of the LIFTFAST operation, the variable

is set internally by the NC to the value "1".

The variable must be reset to the initial state ($AC_LIFTFAST=0)

by the evaluating program (if available), in order to be able to

detect a subsequent LIFTFAST.

Return value

0: Initial state

1: LIFTFAST has been executed

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

0

0

1

Addressing

Line index:

Max. line index:

1

Read access

acMea (C, S)

$AC_MEA

Touch probe has switched

Return value

No. of touch probe

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_UWORD

0

0

1

Addressing

Line index:

Max. line index:

2

Read access

acMeasActPlane (C, S)

$AC_MEAS_ACT_PLANE

Plane setting

Plane setting for measurement calculation

Return value

0: G17, 1: G18, 2: G19

NC variables

240

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

acMeasCornerSetangle (C, S)

$AC_MEAS_CORNER_SETANGLE

Addressing

Line index:

Max. line index:

1

Read access and write access

acMeasDNumber (C, S)

$AC_MEAS_D_NUMBER

Tool edge number

Selected tool edge number

Units and value ranges

Physical unit:

Data type:

Minimum value:

-

TYPE_DWORD

0

Addressing

Line index:

Max. line index:

1

Read access and write access

acMeasDiameter (C, S)

$AC_MEAS_DIAMETER

Diameter

Calculated diameter

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

1

Read access

acMeasDirApproach (C, S)

$AC_MEAS_DIR_APPROACH

Approach direction

Approach direction towards workpiece

Return value

0: +x 1: -x 2: +y 3: -y 4: +z 5: -z

Units and value ranges

Physical unit:

Data type:

Minimum value:

Maximum value:

-

TYPE_DWORD

0

5

Addressing

Line index:

Max. line index:

1

Read access and write access

NC variables

242

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

acMeasFineTrans (C, S)

$AC_MEAS_FINE_TRANS

Fine offset

Correction in fine offset

Return value

0: Correction in coarse translation

1: Correction in fine translation

Units and value ranges

Physical unit:

Data type:

Minimum value:

Maximum value:

-

TYPE_DWORD

0

1

Addressing

Line index:

Max. line index:

1

Read access and write access

acMeasFrameSelect (C, S)

$AC_MEAS_FRAME_SELECT

Frame selection

The frame calculated during workpiece measurement is

entered in the selected frame.

Return value

0:

$P_SETFR

10.. 25: $P_CHBFR[0..15]

50.. 65: $P_NCBFR[0..15]

100.. 199: $P_UIFR[0..99]

1010..1025: $P_CHBFR[0..15]

1050..1065: $P_NCBFR[0..15]

Units and value ranges

Physical unit:

Data type:

Minimum value:

Maximum value:

-

TYPE_DWORD

0

1065

Addressing

Line index:

Max. line index:

1

Read access and write access

acMeasInput (C, S)

$AC_MEAS_INPUT[n]

Data for measurement

Data for the workpiece and tool measurement

Units and value ranges

Physical unit:

Data type:

Initial value

-

TYPE_DOUBLE

0

Addressing

Line index:

Max. line index:

10

Read access and write access

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

243

NC variables

3.2 NC variable descriptions

acMeasSema (C, S)

$AC_MEAS_SEMA

Workpiece measurement semaphore

Variable for disabling and enabling the measurement interface

Return value

0: Not assigned

1: Assigned

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_DWORD

0

0

1

Addressing

Line index:

Max. line index:

1

Read access and write access

acMeasSetCoord (C, S)

$AC_MEAS_SET_COORD

Coordinate system of the set point

Return value

0: Work 1: BCS 2: MCS

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

-

TYPE_DWORD

0

0

Read access and write access

acMeasTNumber (C, S)

$AC_MEAS_T_NUMBER

Tool number

Selected tool number

Units and value ranges

Physical unit:

Data type:

Minimum value:

-

TYPE_DWORD

0

Addressing

Line index:

Max. line index:

1

Read access and write access

acMeasToolLength (C, S)

$AC_MEAS_TOOL_LENGTH

Tool length

Calculated tool length

Units and value ranges

Physical unit:

Data type:

mm, inch, user defined

TYPE_DOUBLE

Addressing

Line index:

Max. line index:

1

Read access

NC variables

246

List Manual, 10/2020, 6FC5397-3CP40-6BA4

NC variables

3.2 NC variable descriptions

acMeasToolMask (C, S)

$AC_MEAS_TOOL_MASK

Tool setting

Tool setting for the measurement calculation

Return value

Bit 0: Tool radius is not included in the calculation

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

-

TYPE_DWORD

0

0

Read access and write access

acMeasType (C, S)

$AC_MEAS_TYPE

Measurement type

Measurement type specification

Return value

0: Default

1: x edge

2: y edge

3: z edge

4: Corner 1

5: Corner 2,

6: Corner 3

7: Corner 4

8: Hole

9: Shaft

10: Tool length

11: Tool diameter

12: Groove

13: Web

14: Actual value setting for geo and special axes

15: Actual value setting for special axes only

16: Edge_2P

17: Plane_Angles

18: Plane_Normal

19: Dimension_1

20: Dimension_2

21: Dimension_3

Units and value ranges

Physical unit:

Data type:

Initial value

Minimum value:

Maximum value:

-

TYPE_DWORD

0

0

21

Addressing

Line index:

Max. line index:

1

Read access and write access

NC variables

List Manual, 10/2020, 6FC5397-3CP40-6BA4

247