Nissan Versa Sedan. Manual - part 814

TM-162

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

P072C STUCK IN 1GR

P072C STUCK IN 1GR

DTC Logic

INFOID:0000000009267919

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

• “

TM-162, "Diagnosis Procedure"

” must be performed before starting “DTC CONFIRMATION PROCE-

DURE”.

• Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause

secondary malfunction.

• Always drive vehicle at a safe speed.

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Select the D position.

3. Drive the vehicle.

4. Maintain the following conditions for 5 seconds or more.

5. Check the first trip DTC.
Is “P072C” detected?

YES

>> Go to 

TM-162, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009267920

1.

MALFUNCTION CAUSE SIMULATION TEST

Refer to 

GI-45, "Intermittent Incident"

. 

Is the check result normal?

YES 

>> Replace the transaxle assembly. Refer to 

TM-250, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning parts.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P072C

Stuck in Gear 1

The following diagnosis condi-
tions are met and the detection 
conditions continue for 0.5 sec-
onds or more.
• Diagnosis condition
- Shifting is not in progress.
- Stop lamp switch OFF
• Detection conditions
- Deceleration: Less than 

−

0.35 G

- Gear ratio: 6% or more, or 

−

6% or less compared with 
normal gear ratio

• 2-4 brake solenoid valve
• Control valve assembly

Selector lever

: 1 position

Stop lamp switch

: OFF

Vehicle speed

: 20 km/h (13 MPH) or more

P072D STUCK IN 2GR

TM-163

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P072D STUCK IN 2GR

DTC Logic

INFOID:0000000009267921

DTC DETECTION LOGIC

DTC REPRODUCTION PROCEDURE

CAUTION:

• “

TM-163, "Diagnosis Procedure"

” must be performed before starting “DTC CONFIRMATION PROCE-

DURE”.

• Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause

secondary malfunction.

• Always drive vehicle at a safe speed.

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for 5 seconds or more.

4. Check the first trip DTC.
Is “P072D” detected?

YES

>> Go to 

TM-163, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009267922

1.

MALFUNCTION CAUSE SIMULATION TEST

Refer to 

GI-45, "Intermittent Incident"

. 

Is the check result normal?

YES 

>> Replace the transaxle assembly. Refer to 

TM-250, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning parts.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P072D

Stuck in Gear 2

The following diagnosis condi-
tions are met and the detection 
conditions continue for 0.5 sec-
onds or more.
• Diagnosis condition
- Shifting is not in progress.
- Stop lamp switch OFF
• Detection conditions
- Deceleration: Less than –

0.35 G

- Gear ratio: 6% or more, or 

−

6% or less compared with 
normal gear ratio

• High clutch/low & reverse 

brake solenoid valve

• Control valve assembly

Selector lever

: 2 position

Gear

: 2GR

Stop lamp switch

: OFF

Vehicle speed

: 20 km/h (13 MPH) or more

TM-164

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

P072E STUCK IN 3GR

P072E STUCK IN 3GR

DTC Logic

INFOID:0000000009267923

DTC DETECTION LOGIC

DTC REPRODUCTION PROCEDURE

CAUTION:

• “

TM-164, "Diagnosis Procedure"

” must be performed before starting “DTC CONFIRMATION PROCE-

DURE”.

• Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause

secondary malfunction.

• Always drive vehicle at a safe speed.

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for 5 seconds or more.

4. Check the first trip DTC.
Is “P072E” detected?

YES

>> Go to 

TM-164, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009267924

1.

MALFUNCTION CAUSE SIMULATION TEST

Refer to 

GI-45, "Intermittent Incident"

. 

Is the check result normal?

YES 

>> Replace the transaxle assembly. Refer to 

TM-250, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning parts.

DTC

Trouble diagnosis name

DTC Detection Condition

Possible causes

P072E

Stuck in Gear 3

The following diagnosis condi-
tions are met and the detection 
conditions continue for 0.5 sec-
onds or more.
• Diagnosis condition
- Shifting is not in progress.
- Stop lamp switch OFF
• Detection conditions
- Deceleration: Less than –

0.35 G

- Gear ratio: 6% or more, or 

−

6% or less compared with 
normal gear ratio

• 2-4 brake solenoid valve
• Control valve assembly

Selector lever

: D position (O/D OFF)

Gear

: 3GR

Stop lamp switch

: OFF

Vehicle speed

: 20 km/h (13 MPH) or more

P072F STUCK IN 4GR

TM-165

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P072F STUCK IN 4GR

DTC Logic

INFOID:0000000009267925

DTC DETECTION LOGIC

DTC REPRODUCTION PROCEDURE

CAUTION:

• “

TM-165, "Diagnosis Procedure"

” must be performed before starting “DTC CONFIRMATION PROCE-

DURE”.

• Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause

secondary malfunction.

• Always drive vehicle at a safe speed.

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn the ignition switch OFF and wait for

at least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for 5 seconds or more.

4. Check the first trip DTC.
Is “P072F” detected?

YES

>> Go to 

TM-165, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009267926

1.

MALFUNCTION CAUSE SIMULATION TEST

Refer to 

GI-45, "Intermittent Incident"

. 

Is the check result normal?

YES 

>> Replace the transaxle assembly. Refer to 

TM-250, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning parts.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P072F

Stuck in Gear 4

The following diagnosis condi-
tions are met and the detection 
conditions continue for 0.5 sec-
onds or more.
• Diagnosis condition
- Shifting is not in progress.
- Stop lamp switch OFF
• Detection conditions
- Deceleration: Less than 

−

0.35 G

- Gear ratio: 6% or more, or 

−

6% or less compared with 
normal gear ratio

• Low clutch solenoid valve
• Control valve assembly

Selector lever

: D position

Gear

: 4GR

Stop lamp switch

: OFF

Vehicle speed

: 20 km/h (13 MPH) or more