Nissan Versa Sedan. Manual - part 812

TM-154

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A

P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A

DTC Logic

INFOID:0000000009267912

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Drive the vehicle.

2. Maintain the following conditions for 5 seconds or more.

3. Check the first trip DTC.
Is “P0713” detected?

YES

>> Go to 

TM-152, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009267913

1.

CHECK CIRCUIT BETWEEN TCM AND A/T UNIT (CHECK 1)

1. Turn ignition switch OFF.

2. Disconnect the TCM connector and A/T unit connector. 

3. Check the continuity between the TCM harness connector and the A/T unit harness connector.

Is the check result normal?

YES

>> GO TO 2.

NO

>> Repair or replace malfunctioning part.

2.

CHECK CIRCUIT BETWEEN TCM AND A/T UNIT (CHECK 2)

1. Turn ignition switch ON.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0713

Transmission Fluid Tempera-
ture Sensor “A” Circuit High

Under the following diagnosis 
conditions, the A/T fluid temper-
ature identified by TCM is 

−

40

°C (−40°F) or less continu-

ously for 5 seconds or more.
• Diagnosis condition
- Ignition switch: ON
- Vehicle speed: 10 km/h (7 

MPH) or more

- Selector lever: D position
- TCM power supply voltage: 

10 V <TCM power supply 
voltage <16 V

• Harness or connector

(Open circuit or short circuit 
to the power supply in the flu-
id temperature sensor circuit)

• A/T fluid temperature sensor

Vehicle speed

: 10 km/h (7 MPH) or more

Selector lever

: D position

TCM harness connector

A/T unit harness connector

Continuity

Connector

Terminal

Connector

Terminal

F44

12

F46

11

Exists

11

16

P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-155

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

2. Check the voltage between the TCM harness connector and ground.

Is the check result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning part.

3.

CHECK FLUID TEMPERATURE SENSOR

Check the fluid temperature sensor. Refer to 

TM-155, "Component Inspection (A/T Fluid Temperature Sen-

sor)"

.

Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace the malfunctioning parts.

Component Inspection (A/T Fluid Temperature Sensor)

INFOID:0000000009267914

1.

CHECK A/T FLUID TEMPERATURE SENSOR

Measure the resistance between the A/T unit connector terminals.

Is the check result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of the A/T fluid temperature sensor. Replace the transaxle assembly. Refer

to 

TM-250, "Removal and Installation"

.

TCM harness connector

Ground

Voltage

Connector

Terminal

F44

12

Ground

Approx. 0 V

A/T unit connector

Condition

Resistance

Terminal

11

16

A/T fluid temperature: 20

°C (68°F)

Approx. 6.5 k

Ω

A/T fluid temperature: 50

°C (122°F)

Approx. 2.2 k

Ω

A/T fluid temperature: 80

°C (176°F)

Approx. 0.87 k

Ω

TM-156

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

P0717 INPUT SPEED SENSOR A

P0717 INPUT SPEED SENSOR A

DTC Logic

INFOID:0000000009267915

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for 5 seconds or more.

4. Stop the vehicle.

5. Check the first trip DTC.
Is “P0717” detected?

YES

>> Go to 

TM-156, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009267916

1.

CHECK INPUT SPEED SENSOR POWER CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect the transaxle assembly connector.

3. Turn ignition switch ON.

4. Check the voltage between the A/T unit harness connector and ground.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0717

Input/Turbine Speed Sensor “A” 
Circuit No Signal

Under the following diagnosis 
conditions, the input speed sen-
sor value is less than 600 rpm 
continuously for 5 seconds or 
more.
• Diagnosis condition
- Engine speed: More than 

1,500 rpm

- Position: Other than P or N
- Idle switch: OFF
- Vehicle speed: More than 40 

km/h (25 MPH)

- TCM power supply voltage: 

10 V <TCM power supply 
voltage <16 V

• Harness or connector

(Open circuit or short circuit in 
the input speed sensor cir-
cuit)

• Input speed sensor

Engine speed

: More than 1,500 rpm

Accelerator pedal position

: 0.5/8.0 or more

Selector lever

: D position

Vehicle speed

: More than 40 km/h (25 MPH)

P0717 INPUT SPEED SENSOR A

TM-157

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the check result normal?

YES 

>> GO TO 2.

NO

>> Check the TCM power supply. Refer to 

TM-216, "Diagnosis Procedure"

.

2.

CHECK INPUT SPEED SENSOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Check the continuity between the A/T unit harness connector and ground.

Is the check result normal?

YES 

>> GO TO 3.

NO

>> Check or repair the malfunction items.

3.

CHECK INPUT SPEED SENSOR SIGNAL CIRCUIT

1. Disconnect the TCM connector.

2. Check the continuity between the TCM harness connector and the A/T unit harness connector.

Is the check result normal?

YES 

>> GO TO 4.

NO

>> Check or repair the malfunction items.

4.

CHECK INPUT SPEED SENSOR TCM CIRCUIT (CHECK 3)

Check the continuity between TCM harness connector and ground.

Is the check result normal?

YES 

>> GO TO 5.

NO

>> Check or repair the malfunction items.

5.

CHECK TCM INPUT SIGNALS

1. Connect all of the disconnected connectors.

2. Lift the vehicle.

3. Start the engine.

4. Check the frequency of the input speed sensor.

A/T unit harness connector

Ground

Voltage

Connector

Terminal

F46

14

Ground

Approx. 5 V

A/T unit harness connector

Ground

Continuity

Connector

Terminal

F46

16

Ground

Exists

TCM harness connector

A/T unit harness connector

Continuity

Connector

Terminal

Connector

Terminal

F44

35

F46

10

Exists

TCM harness connector

Ground

Continuity

Connector

Terminal

F44

35

Ground

Does not exist