Nissan Rogue. Manual - part 1124

SRC-46

< DTC/CIRCUIT DIAGNOSIS >

B0001, B0002 DRIVER AIRBAG MODULE

Is the DTC detected?

YES

>> Refer to 

SRC-46, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011279544

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

• Visible damage to connector or terminal

• Loose terminal

• Poor connection

NOTE:

All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component

(including any in-line connectors). 

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Perform one of the following repairs:

• Visible damage: Replace the harness.

• Loose terminal: Secure the terminal.

• Poor connection: Secure the connection.

2.

CONFIRM DTC

1. Reconnect all harness connectors.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 3.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

3.

WIRING HARNESS

Check the wiring harness for visible damage.

NOTE:

The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component

(including any in-line connectors).
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace the harness.

4.

CHECK SPIRAL CABLE CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-

nector.

3. Check continuity between driver air bag module harness connector and combination switch (spiral cable)

harness connector.

4. Check continuity between driver air bag module harness connector and ground.

Driver air bag module

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Connector

Terminal

B92

29

M53

4

Yes

30

3

B93

32

2

31

3

B0001, B0002 DRIVER AIRBAG MODULE

SRC-47

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-15, "Removal and Installation"

.

5.

CONFIRM DTC

1. Reconnect all harness connectors.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 6.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

6.

AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace the air bag diagnosis sensor unit. Refer to 

SR-26, "Removal and Installation"

.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 7.

NO

>> Clear DTC. Inspection End.

7.

DRIVER AIR BAG MODULE

1. Replace the driver air bag module. Refer to 

SR-12, "Removal and Installation"

.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 8.

NO

>> Clear DTC. Inspection End.

8.

RELATED HARNESS

Replace the related harness.

>> END

Driver side air bag module

Ground

Continuity 

Connector

Terminal

B92

29

No

30

B93

32

31

SRC-48

< DTC/CIRCUIT DIAGNOSIS >

B0010, B0011 PASSENGER AIRBAG MODULE

B0010, B0011 PASSENGER AIRBAG MODULE

DTC Logic

INFOID:0000000011279545

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.

CHECK SELF DIAGNOSTIC RESULT

1. Turn ignition switch ON.

2. Check for DTC using CONSULT.
Is the DTC detected?

YES (Current DTC)>>Refer to 

SRC-48, "Diagnosis Procedure"

.

YES (Past DTC)>>GO TO 2.

NO

>> Inspection End.

2.

ERASE SELF DIAGNOSTIC RESULT

Erase the DTC using CONSULT.
Can the DTC be erased?

YES

>> Inspection End.

NO

>> Refer to 

SRC-48, "Diagnosis Procedure"

.

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.

CHECK SELF DIAGNOSTIC RESULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-14, "On Board Diagnosis Function"

.

NOTE:

SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?

YES

>> Refer to 

SRC-48, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011279546

1.

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

CONSULT name

DTC

DTC detecting condition

Repair order

ASSIST AIRBAG MODULE CIRCUIT 

[OPEN]

B0010

Front passenger air bag module circuit 
(AS1) is open.

Refer to 

SRC-48, "Diagnosis Proce-

dure"

.

ASSIST AIRBAG MODULE CIRCUIT 

[VB-SHORT]

Front passenger air bag module circuit 
(AS1) is shorted to a power supply cir-
cuit.

ASSIST AIRBAG MODULE CIRCUIT 

[GND-SHORT]

Front passenger air bag module circuit 
(AS1) is shorted to ground.

ASSIST AIRBAG MODULE CIRCUIT 

[SHORT]

Front passenger air bag module cir-
cuits (AS1) are shorted to each other.

ASSIST AIRBAG MODULE 2ND CIRCUIT 

[OPEN]

B0011

Front passenger air bag module circuit 
(AS2) is open.

ASSIST AIRBAG MODULE 2ND CIRCUIT 

[VB-SHORT]

Front passenger air bag module circuit 
(AS2) is shorted to a power supply cir-
cuit.

ASSIST AIRBAG MODULE 2ND CIRCUIT 

[GND-SHORT]

Front passenger air bag module circuit 
(AS2) is shorted to ground.

ASSIST AIRBAG MODULE 2ND CIRCUIT 

[SHORT]

Front passenger air bag module cir-
cuits (AS2) are shorted to each other.

B0010, B0011 PASSENGER AIRBAG MODULE

SRC-49

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

• Visible damage to connector or terminal

• Loose terminal

• Poor connection

NOTE:

All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component

(including any in-line connectors). 

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Perform one of the following repairs:

• Visible damage: Replace the harness.

• Loose terminal: Secure the terminal.

• Poor connection: Secure the connection.

2.

CONFIRM DTC

1. Reconnect all harness connectors.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 3.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

3.

WIRING HARNESS

Check the wiring harness for visible damage.

NOTE:

The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component

(including any in-line connectors).
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace the harness.

4.

CONFIRM DTC

1. Reconnect all harness connectors.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 5.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

5.

AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace the air bag diagnosis sensor unit. Refer to 

SR-26, "Removal and Installation"

.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 6.

NO

>> Clear DTC. Inspection End.

6.

FRONT PASSENGER AIR BAG MODULE

1. Replace the front passenger air bag module. Refer to 

SR-17, "Removal and Installation"

.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 7.

NO

>> Clear DTC. Inspection End.

7.

RELATED HARNESS

Replace the related harness.

>> END