Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual - part 1766

DIAGNOSIS 7A2-115

No. C12: Large Shock When Gear is Shifted to 1st to 2nd or 2nd

to 1st

No. C13: Large Shock When Gear is Shifted to 2nd to 3rd or 3rd to

2nd

No. C14: Large Shock When Gear is Shifted to 3rd to 4th or 4th to

3rd

No. C15: Large Shock When Kick-down
No. C16: Large Shock When No Acceleration
No. C17: Large Shock When Gear is Shifted Down to 2nd to 1st in

L Range

No. C18: Large Shock (Other)
No. C19: Large Shock When Vehicle Speed is Downed by No

Accelerator Pedal or Vehicle is Stopped

Description:

•

Large shock is felt when the accelerator pedal is stepped on for acceleration and the gear is shifted up or down.

•

Large shock is felt when the accelerator pedal is stepped on for kick-down.

•

Large shock is felt when the accelerator pedal is not stepped on.

•

Large shock is felt when the shift lever is selected in L range.

Diagnosis Hints:

•

Basically same causes as "No. C1 - C8: Engine races up (slip)" are considered.

No. C20: Large lock-up shock

Description:

•

Large shock is felt at lock-up.

Diagnosis Hints:

•

Out of properties of input sensor or faulty lock-up piston pressure system are considered.

•

Trouble diagnosis flow is basically the same as "No. I1: No lock-up".

No. C21: Shift Down or Engine Over-run When The Accelerator

Pedal is Stepped on in 4th Gear

Description:

•

Shift down or engine over-run above the kick-down area.

Diagnosis Hints:

•

Basically same causes as "No. C1 - C8: Engine races up (slip)" are considered.

7A2-116 DIAGNOSIS

No. D1: Faulty Gear Shifting (Different from Shift Pattern)

Description:

•

Gear is shifted, different from the specified shift pattern.

Diagnosis Hints:

•

When inspecting faulty gear shifting, it is important to distinguish between the fault of electric system and

mechanical system (AT main unit).

•

Fault of electric system.

Monitor the output signal (each solenoid driving signal) using with Tech 2. If a trouble signal is sent to the

solenoid synchronously with the faulty gear shifting, the fault is originated in the electric system.

Monitor the input signal (signal from each sensor) using with Tech 2 and find an input signal by which the output

signal (each solenoid driving signal) is subjected to fault.

Fault of the electric system may be derived from temperature or vibration. For instance, though the engine is

normal while it is cold, fault may occur when the engine is warmed up or vehicle is running.

•

Fault of mechanical system.

If the gear is incorrectly shifted irrespective of operating signal (ON-OFF) of each solenoid, the faulty is

originated from the machine system (AT).

If the clutch slips, ATF smells burnt, contaminated to be black or the stall speed increases.

Possible Cause:

•

Disordered select cable.

•

Disordered inhibitor switch.

•

Slip

clutch.

If slip of clutch is caused, a DTC (gear ratio error) is stored.

•

Fixing at 3rd position (fail-safe activated)

Since the gear is fixed at the 3rd position because of the fail-safe function, a trouble that "Faulty gear

shifting" is resulted. In this case, the DTC is memorized.

When TCM stops operation because of faulty TCM ground, the gear is fixed at the 3rd position because

of a mechanical reason. In this case, no DTC is memorized.

••••

Incorrect properties of throttle opening signal (serial communication) of throttle position sensor.

The throttle opening signal which is sent by serial communication from ECM and TCM is an important

signal for gear shifting. In case of ECM fault or when the throttle position sensor does not issue voltage

signal according to the throttle opening, the gear is not shifted by stepping over the accelerator.

If the output voltage of the throttle position sensor changes freely even though the throttle opening is

constant, the gear is shifted incorrectly.

•

Faulty speed sensor.

DIAGNOSIS 7A2-117

When signal from the speed sensor becomes out of order, it may be judged a result of changed vehicle

speed and faulty gear shifting may be the causes.

••••

Trouble in control valve body (faulty operation, sticking, clogged oil passage)

Step

Action

Yes

Dislocation or disordered of select lever.
Does the vehicle move when the brake is released in a position
other than the P range and the vehicle is pushed?

Go to Step 2

Adjust the select

cable.

Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)

Go to Step 3

Are any DTCs stored?

Go to DTC Chart

Go to Step 4

Are the quantity, contamination and smell normal?

If the ATF level is

low, replenish up to

the specified level.

Go to Step 5

If ATF is extremely

black and

contaminated and

smells burnt, slip of

the clutch is

supposed.

7A2-118 DIAGNOSIS

Step

Action

Yes

Inspection of electrical or mechanical fault
Is signal to each solenoid and pressure switch changed
synchronously to the faulty gear shift?

Control Valve

TCM

B12

B20

RED/YEL

WHT/BLK

2-4 Brake Pressure SW

Terminal

Assembly

YEL

E54

(7)

(12)

(1)

H23

(12)

(10)

C95

(1)

(12)

(20)

RED/YEL

YEL

WHT/BLK

L&R Brake Pressure SW

High Clutch Pressure SW

H22

(8)

Control Valve

TCM

B22 (GND)

BLU/BLK

W HT/BLU

L&R Brake Solenoid

Terminal

Assembly

BLK/YEL

RED

2-4 Brake Solenoid

High Clutch Solenoid

Low Clutch Solenoid

E54

(5)

(9)

(10)

(3)

(11)

H23

(11)

(5)

(7)

(2)

(1)

GRY/RED

C95

(6)

(7)

(8)

(9)

(22)

BLU/BLK

BLK/YEL

RED

W HT/BLU

GRY/RED

Range

TCM terminal

Gear

B20

(High clutch

pressure SW)

(2-4 brake pressure

SW)

B12 (Low & reverse
brake pressure SW)

More than 10V

Reverse

More than 10V

D, 3, 2

1st

More than 10V

2nd

More than 10V

3rd

More than 10V

4th

More than 10V

1st

More than 10V

2nd

More than 10V

3rd

More than 10V

4th

More than 10V

R a n g e

T C M te rm in a l

G e a r

B 8

(H ig h c lu tc h

s o le n o id )

B 9

(L o w c lu tch

s o le n o id )

B 7

(2 -4 b ra k e

s o le n o id )

B 6

(L o w & re v e rs e

b ra k e s o le n o id )

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .2 V

(A C ra n g e )

R e v e rs e

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

D , 3 , 2

1 s t

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

2 n d

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

3 rd

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

4 th

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

1 s t

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

2 n d

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

3 rd

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

4 th

A p p ro x . 6 .8 V

(A C ra n g e )

A p p ro x . 6 .8 V

(A C ra n g e )

Go to Step 6

In case of fault in

the machine

system, repair that

portion or replace

the unit.

Slip of clutch or fault

of control valve.

Content .. 1764 1765 1766 1767 ..