Freightliner Century Class. Manual - part 5

 

  Index      Freightliner     Freightliner Century Class - service manual 2016 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  3  4  5  6   ..

 

 

Freightliner Century Class. Manual - part 5

 

 

Maintenance Operation Sets for Groups 00 through 83

Maint.

No.

Operation Description

Service Schedules

I, II, and III

Service Schedule

IV

IM

M1

M2

M3

IM

M1

M2

M3

00–04

Lubrication and Fluid Level Check

01–01

Engine Noise Panel Inspection (noise emission control)

01–02

Engine Drive Belt Inspection

01–03

Engine Mount Inspection (noise emission control)

*

01–04

Engine-Support Fasteners Check (noise emission control)

09–01

Air Cleaner Element Inspection and Replacement

13–01

Air Compressor Inspection

15–01

Alternator, Battery, and Starter Check

20–01

Pressure Relief Cap Check

20–02

Radiator Pressure-Flushing and Coolant Change

20–03

Fan Clutch Check (noise emission control)

25–01

Eaton Fuller Clutch Release Bearing Lubrication

25–02

Clutch Release Cross-Shaft Lubrication

25–03

Sleeve Assembly Bronze Bushing Lubrication

25–04

Meritor Clutch Release Bearing Lubrication

26–01

Manual Transmission Fluid Change, and Magnetic Plug Cleaning
(synthetic lubricant)

26–02

Allison Transmission Fluid and Filter Change

26–03

Manual Transmission Air Filter/Regulator Check, Cleaning, or
Replacement

26–04

Transmission Fluid Level Inspection

31–01

Fifth Wheel Inspection

31–02

Fifth Wheel Lubrication

31–03

Frame Fastener Torque Check

31–04

Trailer Electrical Connector Lubrication

31–05

Premier 690 Coupling Inspection

32–01

Suspension Inspection

32–02

Suspension Lubrication

32–03

Suspension U-Bolt Torque Check

33–01

Knuckle Pin Lubrication, Meritor Axles

33–02

Tie Rod Inspection

33–03

Tie Rod Lubrication, Meritor Axles

33–04

All-Axle Alignment Check

33–05

Knuckle Pin Lubrication, Dana Spicer Axles

33–06

Tie Rod Lubrication, Dana Spicer Axles

General Information

00

Maintenance Operation Sets Table: 00–09

00/17

Maintenance Operation Sets for Groups 00 through 83

Maint.

No.

Operation Description

Service Schedules

I, II, and III

Service Schedule

IV

IM

M1

M2

M3

IM

M1

M2

M3

33–07

Basic Inspection, Meritor Unitized Wheel Ends

33–08

End-Play Check, Meritor Unitized Wheel Ends

33–09

Kingpin Lubrication, Detroit

Axles

§

33–10

Tie Rod Lubrication, Detroit

Axles

§

35–01

Axle Lubricant and Filter Change, and Magnetic Strainer Cleaning

35–02

Axle Breather and Axle Lubricant Level Inspection

40–01

Wheel Nut and Rim Nut Check

40–02

Tire Check

41–01

Driveline Inspection

41–02

Driveline Lubrication

42–01

Air Brake System Valve Inspection

42–02

Air Dryer Desiccant Replacement

42–03

Air Dryer Inspection

42–04

Alcohol Evaporator Cleaning and Inspection

42–05

Dana Spicer Camshaft Bracket Lubrication

42–06

Dana Spicer, Haldex, and Gunite Slack Adjuster Lubrication

42–07

Meritor Camshaft Bracket Lubrication

42–08

Meritor Slack Adjuster Lubrication

42–09

Bendix E–6 Foot Control Valve Inspection and Lubrication

42–10

Brake Inspection

42–11

Versajust Slack Adjuster Inspection and Lubrication

46–01

Drag Link Inspection

46–02

Power Steering Fluid and Filter Change

46–03

Power Steering Fluid Level Inspection

46–04

Power Steering Gear Lubrication

46–05

Drag Link Lubrication

46–06

Rack and Pinion Steering Gear Inspection

46–07

Bellows Replacement, Rack and Pinion Steering Gear

47–01

Fuel Filter Replacement

47–02

Fuel Separator Sight Bowl Cleaning and Element Replacement

47–03

Fuel Tank Band-Nut Tightening

49–01

Exhaust System Inspection (noise emission control)

49–02

CAT CGI Bellows Replacement

60–01

Cab Suspension Air Bag Inspection

General Information

00

Maintenance Operation Sets Table: 00–09

00/18

Maintenance Operation Sets for Groups 00 through 83

Maint.

No.

Operation Description

Service Schedules

I, II, and III

Service Schedule

IV

IM

M1

M2

M3

IM

M1

M2

M3

60–02

Cab Tilt Pump Reservoir Fluid Level and System Check

60–03

Cab Access Stairs Inspection, Argosy COE

60–04

Mirror Folding Check

72–01

Door Seal, Door Latch, and Door Hinge Lubrication

83–01

Air Conditioner Inspection

83–02

Air Filter Replacement

**

88–01

Hood Rear Support Lubrication

*

At engine overhaul, and whenever the engine has been removed, inspect the lower and upper isolators, and replace them if they are worn.

Inspect Meritor Unitized Wheel Ends at 200,000 miles (321 870 km), and then every 50,000 miles (80 470 km).

Check the end play at 200,000 miles (321 870 km), and then every 200,000 miles (321 870 km).

§

For Schedule II vehicles with Detroit axles, complete this procedure once a year or every 25,000 miles (40 000 km), whichever comes first.

Complete this procedure every 25,000 miles (40 225 km), 3 months, or 500 operating hours, whichever comes first.

**

Replace the HVAC filters every 6 months regardless of mileage.

General Information

00

Maintenance Operation Sets Table: 00–09

00/19

Noise Emission Control
Maintenance

Federal Law, Part 205:
Transportation Equipment Noise
Emission Controls

Part 205, Transportation Equipment Noise Emission
Controls, requires the vehicle manufacturer to fur-
nish, with each new vehicle, such written instructions
for the proper maintenance, use, and repair of the
vehicle by the ultimate purchaser to provide reason-
able assurance of the elimination or minimization of
noise-emission-control degradation throughout the
life of the vehicle. In compliance with the law, the
noise emission controls maintenance information in
each applicable group of this manual, in conjunction
with the vehicle workshop manual, provides these
instructions to owners.

Recommendations for
Replacement Parts

Replacement parts used for maintenance or repair of
noise emission controls should be genuine Freight-
liner parts. If other than genuine Freightliner parts
are used for replacement or repair of components
affecting noise emission control, the owner should be
sure that such parts are warranted by their manufac-
turer to be equivalent to genuine Freightliner parts in
performance and durability.

Freightliner Noise Emission
Controls Warranty

Refer to the vehicle owner’s warranty information
book for warranty information concerning noise emis-
sion controls.

Tampering With Noise Controls is
Prohibited

Federal law prohibits the following acts or the caus-
ing thereof:

1.

The removal or rendering inoperative by any per-
son (other than for purposes of maintenance,
repair, or replacement) of any device or element
of design incorporated into any new vehicle for

the purpose of noise control, prior to its sale or
delivery to the ultimate purchaser, or while it is in
use.

2.

The use of the vehicle after such device or ele-
ment of design has been removed or rendered
inoperative by any person.

Among those acts presumed to constitute tam-
pering are the acts listed below:

A. Removal of engine noise-deadening panels.

B. Removal of cab-tunnel or hood noise-

deadening panels.

C. Removal of, or rendering inoperative, the en-

gine speed governor so as to allow engine
speed to exceed manufacturer’s specifica-
tions.

D. Removal of, or rendering inoperative, the fan

clutch, including bypassing the control on
any thermostatic fan drive to cause it to op-
erate continuously.

E. Removal of the fan shroud.

F.

Removal of, or rendering inoperative, ex-
haust components, including exhaust pipe
clamping.

G. Removal of air intake components.

Maintenance Instructions

Scheduled intervals are in the maintenance tables in
this group. A "Verification of Inspections Log (Groups
01, 20, and 49)" follows, and should be filled in each
time noise emission controls on the vehicle are main-
tained or repaired.

General Information

00

00/20

 

 

 

 

 

 

 

Content   ..  3  4  5  6   ..