|
|
2D 1595Ford Fiesta Remake HCS engines Cylinder head Maximum permissible gasket surface distortion (measured over 0.15 mm Valve seat angle (inlet and exhaust) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45º Valve seat width (inlet and exhaust) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.18 to 1.75 mm* *The inlet and exhaust valves have special inserts which cannot be recut using conventional tools. Valves - general Inlet Exhaust Valve length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103.7 to 104.4 mm 104.2 to 104.7 mm Valve head diameter: 1.0 and 1.1 litre engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32.90 to 33.10 mm 28.90 to 29.10 mm 1.3 litre engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34.40 to 34.60 mm 28.90 to 29.10 mm Valve stem diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0 mm 7.0 mm Valve stem-to-guide clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.020 to 0.069 0.046 to 0.095 Cylinder block Cylinder bore diameter: 1.0 and 1.1 litre engines: Standard class 1 (or A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68.68 to 68.69 mm Standard class 2 (or B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68.69 to 68.70 mm Standard class 3 (or C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68.70 to 68.71 mm Oversize 0.5 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69.20 to 69.21 mm Oversize 1.0 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69.70 to 69.71 mm 1.3 litre engines: Standard class 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73.94 to 73.95 mm Standard class 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73.50 to 73.96 mm Standard class 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73.96 to 73.97 mm Oversize 0.5 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74.50 to 74.51 mm Oversize 1.0 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75.00 to 75.01 mm Chapter 2 Part D: Camshaft and tappets - removal, inspection and refitting (HCS engines) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Crankshaft - refitting and main bearing running clearance check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Crankshaft - removal and inspection . . . . . . . . . . . . . . . . . . . . . . . . 12 7 Cylinder head - reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Cylinder head and valve components - cleaning and inspection . . . 8 Engine - initial start-up after overhaul . . . . . . . . . . . . . . . . . . . . . . . . 19 3 Engine overhaul - preliminary information . . . . . . . . . . . . . . . . . . . . . 6 Engine overhaul - reassembly sequence . . . . . . . . . . . . . . . . . . . . . 15 2 Engine/transmission - removal and refitting (CVH and PTE engines) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Engine/transmission - removal and refitting (Zetec engines) . . . . . . 5 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Main and big-end bearings - inspection . . . . . . . . . . . . . . . . . . . . . . 14 bearing running clearance check . . . . . . . . . . . . . . . . . . . . . . . . . 18 Piston/connecting rod assemblies - removal and inspection . . . . . . 11 2D•1 Specifications Contents Easy, suitable for Fairly easy, suitable Fairly difficult, Difficult, suitable for Very difficult, Degrees of difficulty 5 4 3 2 1 |