Dodge Dakota (ND). Manual - part 1196

 

  Index      Dodge     Dodge Dakota (ND) 2005 - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1194  1195  1196  1197   ..

 

 

Dodge Dakota (ND). Manual - part 1196

 

 

14. Remove the carpet (1) from the vehicle.

INSTALLATION

Club Cab, Without Rear Jumper Seats

WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental
restraint system before attempting any steering wheel, steering column, airbag, occupant classification sys-
tem, seat belt tensioner, impact sensor, or instrument panel component diagnosis or service. Disconnect
and isolate the battery negative (ground) cable, then wait two minutes for the system capacitor to discharge
before performing further diagnosis or service. This is the only sure way to disable the supplemental
restraint system. Failure to take the proper precautions could result in accidental airbag deployment.

WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.

NOTE: Carpet for Quad Cab models shown. Club
Cab similar.

1. For vehicles equipped with a manual shift transmis-

sion, remove the cutout (2) from the carpet for the
shifter assembly.

2. Position the carpet (1) in the vehicle.

23 - 196

INTERIOR

ND

NOTE: Cab back trim panel with jumper seats shown. Trim panel without similar.

3. Install the cab back trim panel, (Refer to 23 - BODY/INTERIOR/PANEL-CAB BACK TRIM - INSTALLATION).

4. Install the lower C-pillar trim panels, (Refer to 23 -

BODY/INTERIOR/PANEL-C PILLAR LOWER TRIM
- INSTALLATION).

5. Install the upper C-pillar trim panels, (Refer to 23 -

BODY/INTERIOR/PANEL-C PILLAR UPPER TRIM
- INSTALLATION).

6. Install the jack storage compartment cover.

ND

INTERIOR

23 - 197

NOTE: Mini floor console shown. Full floor con-
sole different.

7. Install the floor console, (Refer to 23 - BODY/INTE-

RIOR/CONSOLE-FLOOR - INSTALLATION).

NOTE: Electric front seats shown. Other seats
similar.

8. Install the front seats, (Refer to 23 - BODY/SEATS/

SEAT-FRONT - INSTALLATION).

9. Position the retractor (1) mounting bracket to the

mounting holes in the floor panel inboard of the
door sill (4). Be certain that the seat belt webbing
between the retractor and the turning loop is not
twisted.

10. Install the two screws (2) that secure the retractor

bracket to the floor panel. Tighten the screws to
39 N·m (29 ft. lbs.).

11. Reconnect the body wire harness connector (3) to

the seat belt tensioner initiator on the retractor.

23 - 198

INTERIOR

ND

12. Install the rear door sill scuff plates, (Refer to 23 -

BODY/INTERIOR/PLATE-DOOR

SCUFF

-

INSTALLATION).

NOTE: Cowl trim panel for Quad Cab models
shown. Club Cab similar.

13. Install the cowl trim panels, (Refer to 23 - BODY/

INTERIOR/PANEL-COWL

TRIM

-

INSTALLATION).

14. Install the outer front seat belt retractor covers,

(Refer to 23 - BODY/INTERIOR/COVER-OUTER
FRONT

SEAT

BELT

RETRACTOR

-

INSTALLATION).

ND

INTERIOR

23 - 199

 

 

 

 

 

 

 

Content   ..  1194  1195  1196  1197   ..