DAF LF45, LF55 Series. Manual - part 541

 

  Index      DAF     DAF LF45, LF55 Series - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  539  540  541  542   ..

 

 

DAF LF45, LF55 Series. Manual - part 541

 

 

7

LF45/55 series

Inspection and adjustment

FRONT AXLE, 152N

2-1

2. INSPECTION AND ADJUSTMENT

2.1 INSPECTION AND ADJUSTMENT OF SWIVEL AXLE PLAY

Checking swivel axle play
1.

The vehicle must have its wheels on the
ground.

Note:
If the wheels have been taken off the front
axle (to be overhauled, for example), the
swivel axle will hang loose on the axle end.
In that case, place a jack under the swivel
axle so that the swivel axle is pushed
against the underside of the axle end.

2.

Using a feeler gauge, measure the distance
between the shim and the swivel axle at
(A). Take measurements in several places.
Compare the measured value with the
admissible play, see “Technical data”.

Note:
The play should be about equal around the
entire circumference of the axle end. If it is
not, this indicates that there is radial play in
the needle bearings. If there is radial play
and one of the measurements taken differs
from the specified value, the needle
bearings must be replaced, see “Removal
and installation”.

If excessive axial play is measured around
the entire circumference of the axle end,
the swivel axle thrust bearing is probably
worn.

;;;;;;;

;;;;;;;

;;;;;;;

;;;;;;;

;;;

;;;

;;

;;;

;;;

;;;

;;;

;;

;;

;;

;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;;

;

;

;

;

;;

;;

;;

;;

;;

;;

;;

;;

;;;

;;

;;

;;

;;

;

;

;

;

;

;

;

;

;;;;;

;;;;;

;;

;;

;

;;

;;

;

;

;

;

;

;;;;;;;

;;;;;;;

;;;;;;;

;;;;;;;

;;;

;;;

;;

;;

;;;

;;;

;;;

;;;

;;

;;

;;

;

;

;

;

;;;

;;;

;;;

;;;

;;;

;;;;;

;;;;;

;;

;;

;

;;

;;

;

;

;

;

;

;;

;;

;;

A

S7 00 579

;;;;

;;;;

8

ᓻ 200322

7

FRONT AXLE, 152N

Inspection and adjustment

LF45/55 series

2-2

Adjusting swivel axle play, split thrust
bearing
1.

Take the swivel axle off the axle end, see
“Removal and installation”.

2.

Degrease and clean the thrust bearing.

3.

Check the thrust bearing for wear and
damage. If in doubt, replace the thrust
bearing.

4.

Check the machined surfaces of the axle
end and the swivel axle for damage.

5.

Take the dust seal (1) off the thrust
washer (2).

6.

Assemble the thrust bearing without
greasing it and without the dust seal (1).
Make sure that the cam on the underside of
the bearing ring (3) falls into the recess of
the shoulder ring (4). See arrows in the
drawing.

7.

Fit the swivel axle with its original shim to
the axle end.

8.

Fit the king pin. Hand-tighten the nut.

9.

Place a jack under the swivel axle, so that
the thrust bearing is pushed against the
axle end.

10. Using a feeler gauge, measure the gap

between the shim and the swivel axle.
If necessary, insert a shim with a different
thickness in order to achieve the specified
axial play, see “Technical data”.

S7 00 114

3

2

1

4

Note:
The thickness of the shim can also be
determined using the formula in the
drawing.

A =

thickness of shim

B =

distance between the swivel axle
contact surfaces

C =

total thickness of the thrust bearing
without the dust seal

D =

axle end dimension

E =

play

S7 00 815

B

D

A

A=B-(C+D+E)

E

C

8

ᓻ 200322

7

LF45/55 series

Inspection and adjustment

FRONT AXLE, 152N

2-3

11. Take the swivel axle off the axle end.

12. Dismantle the thrust bearing and grease the

top (side with ribs and lubricating grooves)
of the bearing ring (3).

13. Fit a new dust seal (1) to the thrust

washer (2).
Make sure that the top of the dust seal is
positioned under the top of the thrust
washer.

14. Install the swivel axle with the correct shim

on the axle end, see “Removal and
installation”.

15. Measure the play again.

Adjusting swivel axle play, compound thrust
bearing
1.

Take the swivel axle off the axle end, see
“Removal and installation”.

2.

Check the thrust bearing for wear and
damage. If in doubt, replace the thrust
bearing.

3.

Check the machined surfaces of the axle
end and the swivel axle for damage.

4.

Fit the swivel axle with its original shim to
the axle end.

5.

Fit the king pin. Hand-tighten the nut.

6.

Place a jack under the swivel axle, so that
the thrust bearing is pushed against the
axle end.

7.

Using a feeler gauge, measure the gap
between the shim and the swivel axle.
If necessary, insert a shim with a different
thickness in order to achieve the specified
axial play, see “Technical data”.

S7 00 114

3

2

1

4

8

ᓻ 200322

7

FRONT AXLE, 152N

Inspection and adjustment

LF45/55 series

2-4

Note:
The thickness of the shim can also be
determined using the formula in the
drawing.

A =

thickness of shim

B =

distance between the swivel axle
contact surfaces

C =

total thickness of the thrust bearing

D =

axle end dimension

E =

play

8.

Take the swivel axle off the axle end.

9.

Install the swivel axle with the correct shim
on the axle end, see “Removal and
installation”.

10. Check the play once again.

S7 00 577

B

D

A

A=B-(C+D+E)

E

C

8

ᓻ 200322

 

 

 

 

 

 

 

Content   ..  539  540  541  542   ..