Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual - part 83

TEST

ACTION

APPLICABILITY

Turn the ignition off.
Disconnect the Body Control Module C2 harness connector.
Using a 12-volt test light, back probe between the Recirculation Door Driver circuit
and the Common Door Driver circuit in the BCM C2 harness connector.
Reconnect the Body Control Module C2 harness connector.
Turn the ignition on.
With the DRBIII

t, select Body, Body Computer, System Tests then Actuate Mode

Doors.
Select Recirc Door.
While observing the test light, press and hold the DRB right arrow key for several
seconds.
While observing the test light, press and hold the DRB left arrow key for several
seconds.
Is the test light on while the right and left arrow keys are pressed?

All

Yes

→ Go To 3

→ Replace and program the Body Control Module in accordance

with the Service Information.
Calibration must be performed after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

Turn the ignition off.
Disconnect the Body Control Module C2 harness connector.
Disconnect the Recirculation Door Actuator harness connector.
Measure the resistance of the Recirculation Door Driver circuit between the BCM C2
harness connector and the Recirculation Door Actuator harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 4

→ Repair the Recirculation Door Driver circuit for an open.

Calibration must be performed after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

Turn the ignition off.
Disconnect the Body Control Module C2 harness connector.
Disconnect the Recirculation Door Actuator harness connector.
Measure the resistance of the Common Door Driver circuit between the BCM C2
harness connector and the Recirculation Door Actuator harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Inspect for missing & broken actuator linkage. Check door for

binding & loss of full range. Inspect housing for missing or broken
stops. Repair as necessary. If linkage and door are okay, replace
Recirc Door Actuator in accordance with Service Info.
Calibration must be performed after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

→ Repair the Common Door Driver circuit for an open.

Calibration must be performed after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

317

HEATING & A/C

RECIRCULATION DOOR STALL TEST FAILURE - ATC & MTC —

Continued

TEST

ACTION

APPLICABILITY

Turn the ignition off.
NOTE: Visually inspect the related wiring harness and circuits. Look for
any chafed, pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
NOTE: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?

All

Yes

→ Repair as necessary.

Calibration must be performed after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

→ Test Complete.

318

HEATING & A/C

RECIRCULATION DOOR STALL TEST FAILURE - ATC & MTC —

Continued

Symptom:

SUN LOAD SENSOR FAILURE - ATC

When Monitored and Set Condition:

SUN LOAD SENSOR FAILURE - ATC

When Monitored:

With the ignition on.

Set Condition:

The BCM detects an abnormally low voltage on the sun sensor signal.

POSSIBLE CAUSES

SUN SENSOR LOW

SUN SENSOR SIGNAL CIRCUIT SHORTED TO GROUND

SUN SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND

BODY CONTROL MODULE - SUN SENSE LOW

TEST

ACTION

APPLICABILITY

NOTE: It is advisable to perform the ATC System Test before attempting to
diagnose this trouble code.
Turn the ignition off.
Disconnect the Sun Sensor/VTSS LED harness connector.
Turn the ignition on.
With the DRBIII

t in Sensor Display, read the Sun Sensor voltage.

Is the voltage below 0.2 volts?

All

Yes

→ Go To 2

→ Replace the Sun Sensor in accordance with the Service Informa-

tion.
Perform BODY VERIFICATION TEST - VER 1.

Turn the ignition off.
Disconnect the Sun Sensor/VTSS LED harness connector.
Disconnect the Body Control Module C1 & C2 harness connectors.
Measure the resistance between ground and the Sun Sensor Signal circuit.
Is the resistance below 100.0 ohms?

All

Yes

→ Repair the Sun Sensor Signal circuit for a short to ground.

Perform BODY VERIFICATION TEST - VER 1.

→ Go To 3

Turn the ignition off.
Disconnect the Sun Sensor/VTSS LED harness connector.
Disconnect the Body Control Module C1 & C2 harness connectors.
Measure the resistance between the Sun Sensor Signal circuit and the Sensor
Ground circuit in the Sun Sensor harness connector.
Is the resistance below 100.0 ohms?

All

Yes

→ Repair the Sun Sensor Signal circuit for a short to the Sensor

Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.

→ Go To 4

319

HEATING & A/C