Chrysler New Yorker. Manual - part 533

TEST 11A

REPAIRING - HEADLAMP WASHERS NOT WORKING PROPERLY

Perform TEST 1A Before Proceeding

FIG. 1

FIG. 2

W

I

N
D

S

H

I

E

L

D

W

I

P
E

R

S
Y
S

T

E

M

730

TEST 11A

REPAIRING - HEADLAMP WASHERS NOT WORKING PROPERLY

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION 
OF ALL COMPONENTS.

START TEST 11A. 

SEE GENERAL INFO 4.0

PERFORM

TURN THE IGNITION 

TURN THE LOW BEAM 

DO THE HEADLAMPS

NO 

"EXTERIOR

ON.

HEADLAMPS ON.

OPERATE PROPERLY?

LIGHTING" TEST 

1A.

YES

PUSH AND THEN 

TURN THE WIPERS TO 

RELEASE THE WASH 

DID THE WIPERS AND

NO 

PERFORM TEST 

THE LOW SPEED

BUTTON ON THE

WASHERS OPERATE

1A.

SETTING. WIPER SWITCH.

PROPERLY?

YES

SYSTEM IS 

DID THE HEADLAMP YES

OPERATEING 

WASHERS TURN ON?

PROPERLY WITH NO 

PROBLEM FOUND. 

NO 

SUBSITUTE THE

WITH THE HEADLAMPS

HEADLAMP WASHER 

ON, PUSH THE WASH 

DID THE HEADLAMP 

YES

REPLACE THE

RELAY WITH A KNOWN

BUTTON ON THE

WASHERS TURN ON?

ORIGINAL HEADLAMP 

GOOD RELAY. 

WIPER SWITCH.

WASHER RELAY.*

FIG. 1

NO 

DISCONNECT THE

WITH AN OHMMETER,

HEADLAMP WASHER 

MEASURE BETWEEN

IS THE RESISTANCE 

NO 

REPAIR THE OPEN 

MOTOR HARNESS

GROUND AND THE

BELOW 5.0 OHMS?

GROUND CIRCUIT.*

CONNECTOR.** GROUND 

CIRCUIT. 

FIG. 2

YES

CONTINUE TEST 
11A ON THE NEXT 

PAGE.

W

I

N
D

S

H

I

E

L

D

W

I

P
E

R

S
Y
S

T

E

M

731

TEST 11A

CONTINUED - REPAIRING HEADLAMP WASHERS NOT WORKING PROPERLY

FIG. 1

FIG. 2

FIG. 3

W

I

N
D

S

H

I

E

L

D

W

I

P
E

R

S
Y
S

T

E

M

732

TEST 11A

CONTINUED - REPAIRING HEADLAMP WASHERS NOT WORKING PROPERLY

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

TEST 11A

CONNECT A TEST LIGHT

CONTINUED FROM BETWEEN THE HEADLAMP 

THE PREVIOUS WASHER 

MOTOR

PAGE.

CONNECTOR CAVITIES 

1 & 2. FIG. 1

DOES THE TEST 

WITH THE DRB ENTER

ACTUATE THE

LIGHT FLASH ON AND

YES

REPLACE THE

"BODY COMPUTER"

HEADLAMP WASHER 

OFF AS THE RELAY

HEADLAMP WASHER 

THEN "ACTUATORS". 

RELAY. 

IS ACTUATED?

MOTOR.*

NO 

REMOVE THE HEADLAMP 

STOP THE

WASHER RELAY. 

ACTUATION. 

FIG. 2

WITH A VOLTMETER, 
MEASURE BOTH FUSED

IS THE VOLTAGE

NO 

REPAIR THE OPEN 

B(+) CIRCUITS.

ABOVE 10.0 VOLTS

FUSED B(+) 

ON BOTH CIRCUITS?

CIRCUITS.* 

FIG. 2

YES

CONNECT A JUMPER 

WITH AN OHMMETER,

REPAIR THE OPEN 

WIRE BETWEEN GROUND 

MEASURE BETWEEN GND

IS THE RESISTANCE 

NO 

HEADLAMP WASHER 

AND CAVITY 4 OF THE

AND THE HEADLAMP 

BELOW 5.0 OHMS?

MOTOR CONTROL

HEADLAMP WASHER 

WASHER MOTOR CONTROL

CIRCUIT.*

RELAY CONN. FIG. 2

CKT. FIG. 1

YES

CONNECT A JUMPER 

WIRE BETWEEN GROUND 

DISCONNECT THE BCM

AND CAVITY 1 OF THE

"C3" HARNESS

HEADLAMP WASHER 

CONNECTOR.** 

RELAY CONN. FIG. 2

WITH AN OHMMETER,

REPAIR THE OPEN 

MEASURE BETWEEN GND

IS 

THE RESISTANCE NO HEADLAMP 

WASHER 

AND THE HEADLAMP BELOW 5.0 OHMS?

RELAY CONTROL

WASHER RELAY CONTROL

CIRCUIT.*

CKT. FIG. 3

YES

REPLACE THE BODY 
CONTROL MODULE.* 

W

I

N
D

S

H

I

E

L

D

W

I

P
E

R

S
Y
S

T

E

M

733