Index Chrysler Chrysler 300M / Concorde / Interpid / LHS, Dodge Interpid - service repair manual 2000-2004 year
Search
Content .. 262 263 264 265 ..
Chrysler 300M, Dodge Interpid. Manual - part 264
FRAME & BUMPERS
TABLE OF CONTENTS
page
FRONT BUMPER REINFORCEMENT
REMOVAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . 1
FRONT FASCIA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
REMOVAL - INTREPID
. . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION - INTREPID
. . . . . . . . . . . . . . . 3
REAR BUMPER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . 3
REAR FASCIA
. . . . . . . . . . . . . . . . . . . . . . . . . . 4
REAR FASCIA - INTREPID
. . . . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . 4
FRAME
SPECIFICATIONS
FRAME DIMENSIONS
. . . . . . . . . . . . . . . . . . . 4
SPECIFICATIONS - TORQUE
. . . . . . . . . . . . . 9
ENGINE CRADLE CROSSMEMBER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . 9
FRONT TOW EYE
. . . . . . . . . . . . . . . . . . . . . . . . . 10
FRONT TOW HOOK BRACKET
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
REAR CROSSMEMBER
DESCRIPTION
OPERATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DISASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . 12
ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . 13
REAR TOW EYE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 15
FRONT BUMPERREINFORCEMENT
(1) Remove front fascia.(2) Remove end plugs in ends of bumper after
removing screws in front of bumper.
(3) Remove attaching bolts from bumper reinforce-
ment to adapter plate through ends of the bumper.(Fig. 1).
(4) If beam is damaged, the adapter plate to rail
welds will have to be cut off
(1) Place reinforcement in position on front of vehi-
cle.
(2) Install attaching bolts to inside of bumper rein-
forcement to adapter plates.
(3) Install end plugs in ends of bumper, using
screws in front of the bumper.
(4) Install front fascia.
Fig. 1 FRONT BUMPER REINFORCEMENT
1-END CAP2-FRONT BUMPER REINFORCEMENT3-END CAP
LH
13 - 1