Toyota Sequoia (2005). Manual - part 45

–

SERVICE SPECIFICATIONS

SUSPENSION AND AXLE

SS–35

177

Companion flange vertical runout

Maximum

0.09 mm (0.0035 in.)

Companion flange horizontal runout

Maximum

0.09 mm (0.0035 in.)

Drive pinion preload (at starting)

New bearing

Reused bearing

1.3 – 1.9 N·m (13 – 19 kgf·cm, 11.4 – 16.7 in.·lbf)

0.8 – 1.1 N·m (8 – 11kgf·cm, 7.0 – 9.7 in.·lbf)

Total preload (at starting)

Drive pinion preload plus 0.4 – 0.6 N·m (4 – 6 kgf·cm, 3.5 – 5.2

in.·lbf)

Drive pinion to ring gear backlash

0.13 – 0.18 mm (0.0051 – 0.0071 in.)

Side gear backlash

0.05 – 0.20 mm (0.0020 – 0.0079 in.)

Ring gear runout

Maximum

0.05 mm (0.0020 in.)

Differential case runout

Maximum

0.04 mm (0.0016 in.)

Rear differential

Drive pinion oil seal drive in depth

0 mm (0 in.)

1.50 mm (0.0590 in.)

1.55 mm (0.0610 in.)

1.60 mm (0.0630 in.)

1.65 mm (0.0650 in.)

Side gear thrust washer thickness

1.70 mm (0.0669 in.)

Side gear thrust washer thickness

1.75 mm (0.0689 in.)

1.80 mm (0.0709 in.)

1.85 mm (0.0728 in.)

1.90 mm (0.0748 in.)

SS–36

–

SERVICE SPECIFICATIONS

SUSPENSION AND AXLE

178

58

2.58 mm (0.1015 in.)

60

2.60 mm (0.1024 in.)

62

2.62 mm (0.1031 in.)

64

2.64 mm (0.1039 in.)

66

2.66 mm (0.1047 in.)

68

2.68 mm (0.1055 in.)

70

2.70 mm (0.1063 in.)

72

2.72 mm (0.1071 in.)

74

2.74 mm (0.1079 in.)

76

2.76 mm (0.1087 in.)

78

2.78 mm (0.1094 in.)

80

2.80 mm (0.1102 in.)

82

2.82 mm (0.1110 in.)

84

2.84 mm (0.1118 in.)

86

2.86 mm (0.1126 in.)

88

2.88 mm (0.1134 in.)

90

2.90 mm (0.1142 in.)

92

2.92 mm (0.1150 in.)

94

2.94 mm (0.1157 in.)

96

2.96 mm (0.1165 in.)

98

2.98 mm (0.1173 in.)

00

3.00 mm (0.1181 in.)

R

diff

ti l

Sid b

i

dj

ti

h

thi k

02

3.02 mm (0.1189 in.)

Rear differential

Side bearing adjusting washer thickness

04

3.04 mm (0.1197 in.)

06

3.06 mm (0.1205 in.)

08

3.08 mm (0.1213 in.)

10

3.10 mm (0.1220 in.)

12

3.12 mm (0.1228 in.)

14

3.14 mm (0.1236 in.)

16

3.16 mm (0.1244 in.)

18

3.18 mm (0.1252 in.)

20

3.20 mm (0.1260 in.)

22

3.22 mm (0.1268 in.)

24

3.24 mm (0.1276 in.)

26

3.26 mm (0.1283 in.)

28

3.28 mm (0.1291 in.)

30

3.30 mm (0.1299 in.)

32

3.32 mm (0.1307 in.)

34

3.34 mm (0.1315 in.)

36

3.36 mm (0.1323 in.)

38

3.38 mm (0.1331 in.)

40

3.40 mm (0.1339 in.)

42

3.42 mm (0.1346 in.)

44

3.44 mm (0.1354 in.)

46

3.46 mm (0.1362 in.)

48

3.48 mm (0.1370 in.)

–

SERVICE SPECIFICATIONS

SUSPENSION AND AXLE

SS–37

179

87

1.87 mm (0.0736 in.)

88

1.88 mm (0.0740 in.)

89

1.89 mm (0.0744 in.)

90

1.90 mm (0.0748 in.)

91

1.91 mm (0.0752 in.)

92

1.92 mm (0.0756 in.)

93

1.93 mm (0.0760 in.)

94

1.94 mm (0.0764 in.)

95

1.95 mm (0.0768 in.)

96

1.96 mm (0.0772 in.)

97

1.97 mm (0.0776 in.)

98

1.98 mm (0.0780 in.)

99

1.99 mm (0.0783 in.)

00

2.00 mm (0.0787 in.)

01

2.01 mm (0.0791 in.)

02

2.02 mm (0.0795 in.)

03

2.03 mm (0.0799 in.)

04

2.04 mm (0.0803 in.)

05

2.05 mm (0.0807 in.)

06

2.06 mm (0.0811 in.)

R

diff

ti l

D i

i i

b

i

dj

ti

h

thi k

07

2.07 mm (0.0815 in.)

Rear differential

Drive pinion bearing adjusting washer thickness

08

2.08 mm (0.0819 in.)

09

2.09 mm (0.0823 in.)

10

2.10 mm (0.0827 in.)

11

2.11 mm (0.0831 in.)

12

2.12 mm (0.0835 in.)

13

2.13 mm (0.0839 in.)

14

2.14 mm (0.0843 in.)

15

2.15 mm (0.0846 in.)

16

2.16 mm (0.0850 in.)

17

2.17 mm (0.0854 in.)

18

2.18 mm(0.0858 in.)

19

2.19 mm (0.0862 in.)

20

2.20 mm (0.0866 in.)

21

2.21 mm (0.0870 in.)

22

2.22 mm (0.0874 in.)

23

2.23 mm (0.0878 in.)

24

2.24 mm (0.0882 in.)

25

2.25 mm (0.0886 in.)

26

2.26 mm (0.0890 in.)

27

2.27 mm (0.0894 in.)

28

2.28 mm (0.0898 in.)

SS–38

–

SERVICE SPECIFICATIONS

SUSPENSION AND AXLE

180

Air suspension

Amount of change in vehicle height

HIGH position:

LOW position (4WD):

LOW position (2WD):

40 mm (1.57 in.)

–30 mm (–1.18 in.)

–15 mm (–0.59 in.)

Air suspension

Difference between the tester value and vehicle height

(D–C measurement):

5 mm (0.20 in.) or less

Height control sensor link

standard length:

6.5 – 15.0 mm (0.26 – 0.59 in.) or less