Content .. 186 187 188 189 ..

Toyota Tundra. Manual - part 188

TELEPHONE:

DIAGNOSTIC TROUBLE CODE CHART - TELEPHONE

SPEAKER:

DIAGNOSTIC TROUBLE CODE CHART - SPEAKER

DTC 01-21 ROM ERROR; DTC 01-22 RAM ERROR

DESCRIPTION

DTC TROUBLE DETECTION CONDITION

63-43

CD-ROM Abnormal

1. CD

2. Radio receiver

63-44

CD Abnormal

Radio receiver

63-45

Eject Error

Radio receiver

63-46

Scratched / Reversed Disc

1. CD

2. Radio receiver

63-47

High Temperature

Radio receiver

63-48

Excess Current

Radio receiver

63-50

Tray Insertion / Ejection Error

Radio receiver

63-51

Elevator Error

Radio receiver

63-52

Clamp Error

Radio receiver

63-78

DSP Error

63-7D

Disc cannot be Played

1. CD

2. Radio receiver

63-7E

No Playable Files

1. CD

2. Radio receiver

63-7F

1. CD

2. Radio receiver

DTC Code

Detection Item

Trouble Area

57-47

Bluetooth Module Initialization
Failed

Radio receiver

DTC Code

Detection Item

Trouble Area

74-40

Short in Speaker Circuit

1. Harness and connector

2. Speaker

3. Stereo component amplifier

DTC Code

DTC Detection Condition

Trouble Area

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra

INSPECTION PROCEDURE

HINT:

After the inspection is completed, clear the DTCs.

1. REPLACE RADIO RECEIVER

a. for Column Shift Type:

Replace the radio receiver (see REMOVAL ).

b. for Floor Shift Type:

Replace the radio receiver (see REMOVAL ).

NEXT: END

DTC 01-D5 ABSENCE OF REGISTRATION UNIT; DTC 01-D8 NO RESPONSE FOR CONNECTION
CHECK; DTC 01-D9 LAST MODE ERROR; DTC 01-DA NO RESPONSE AGAINST ON / OFF
COMMAND; DTC 01-DB MODE STATUS ERROR; DTC 01-DE SLAVE RESET

DESCRIPTION

DTC TROUBLE DETECTION CONDITION

01-21

A malfunction exists in ROM.

Radio receiver

01-22

A malfunction exists in RAM.

DTC

Code

DTC Detection Condition

Trouble Area

01-

D5*1,*3

A device that the sub-code shows is (was)
disconnected from the system when turning the
ignition switch ON or ACC.
The communication condition with the device that
the code shows cannot be obtained when the engine
starts.



Power source circuit of the
component shown by the sub-code



AVC-LAN circuit between the
radio receiver and the component
shown by the sub-code



Component shown by the sub-
code

01-D8*2,

The device indicated by the sub-code is (was)
disconnected from the system after the engine starts.

01-

D9*1,*3

The device that had functioned before the engine
stopped is (was) disconnected from the system when
turning the ignition switch ON or ACC.

01-DA*3

No response is identified when changing mode.
Sound and image do not change by switch operation.

01-

DB*1,*3

A dual alarm is detected.

01-DE*3,

A slave device has been disconnected after the
engine starts

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra

INSPECTION PROCEDURE

1. CHECK "RADIO RECEIVER COMMUNICATION ERROR" IN FLOW CHART

a. Refer to the RADIO RECEIVER COMMUNICATION ERROR .

NEXT: END

DTC 01-D6 NO MASTER; DTC 01-D7 CONNECTION CHECK ERROR

DESCRIPTION

DTC TROUBLE DETECTION CONDITION

HINT:



*1: Even if no fault is present, this trouble code may be stored depending on the battery condition
or engine start voltage.



*2: If the power connector is disconnected after the engine starts, this code is stored after 180
seconds.



*3: If the device is reported as not existing during verification, check the power source circuit and
AVC-LAN circuit for the device.



*4: This code may be stored if the engine is started and the ignition switch is turned to the START
position again.

NOTE:



Before starting troubleshooting, be sure to clear DTCs to erase codes
stored due to the reasons described in the HINT above. Then, check for
DTCs and troubleshoot according to the output DTCs.



The radio receiver is the master unit.



Be sure to clear and recheck DTCs after the inspection is completed to
confirm that no DTCs are output.

NOTE:

Be sure to read the DESCRIPTION before performing the following procedures.

DTC

Code

DTC Detection Condition

Trouble Area

01-

D6*1

When either of the following conditions is
met:



The device that stores (stored) the
code has (had) been disconnected
when the ignition switch is in the ACC
or ON position.



The master device has (had) been
disconnected when this code is stored.



Radio receiver power source circuit



Power source circuit of the component which
has stored this code AVC-LAN circuit
between the radio receiver and the component
which has stored this code

When either of the following conditions is

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra

INSPECTION PROCEDURE

1. CHECK RADIO RECEIVER POWER SOURCE CIRCUIT

a. Refer to the RADIO RECEIVER POWER SOURCE CIRCUIT .

If the power source circuit is operating normally, proceed to the next step.

2. IDENTIFY THE COMPONENT WHICH HAS STORED THIS CODE

a. Enter the diagnostic mode.

01-

D7*2

met:



The device that stored the code has
(had) been disconnected after the
engine starts (started).



The master device has (had) been
disconnected when this code is (was)
stored.



Component which has stored this code



Radio receiver

HINT:



*1: Even if no fault is present, this trouble code may be stored depending on the battery condition
or engine start voltage.



*2: When 210 seconds have elapsed after disconnecting the power supply connector of the master
component with the ignition switch in the ACC or ON position, this code is stored.

NOTE:



Before starting troubleshooting, be sure to clear DTCs to erase codes
stored due to the reasons described in the HINT above. Then, check for
DTCs and troubleshoot according to the output DTCs.



The radio receiver is the master unit.



Be sure to clear and recheck DTCs after the inspection is completed to
confirm that no DTCs are output.

NOTE:

Be sure to read the DESCRIPTION before performing the following procedures.

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra

Content .. 186 187 188 189 ..