Subaru Legacy IV (2008 year). Manual - part 330

EN(H4DOTC)(diag)-141

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

AD:DTC P0137 O2 SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2)

DTC DETECTING CONDITION:
• Two consecutive driving cycles with fault
• GENERAL DESCRIPTION <Ref. to GD(H4DOTC)-55, DTC P0137 O2 SENSOR CIRCUIT LOW VOLT-
AGE (BANK 1 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Criteria.>

CAUTION:
After repair or replacement of faulty parts, perform Clear Memory Mode <Ref. to EN(H4DOTC)(diag)-
52, OPERATION, Clear Memory Mode.>, and Inspection Mode <Ref. to EN(H4DOTC)(diag)-43, PRO-
CEDURE, Inspection Mode.>.
WIRING DIAGRAM:

EN-05670

B83

1 2 3 4
5 6 7 8

B138

B47

1

2

4

6

3

5

E

*

*

B138

B83

3

4

1

2

5

6

B135

B47

B19

B136

B:

C:

B137

D:

5

6

7 8

2

1

9

4

3

10

24

22 23

25

11 12 13 14 15

26 27

28

16

17 18 19 20 21

33 34

29

32

30

31

35

5

6

7

8

2

1

9

4

3

10

24

22 23

25

11 12 13 14 15

26 27

28

16 17 18 19

20 21

29 30 31

32 33

34 35

5

6

7

8

2

1

9

4

3

10

22 23

11 12 13 14 15

24 25

26

16 17

18 19 20 21

27

28 29

30 31

B19

T5

2

2

T5

B19

3

1

4

B21

1 2 3 4

12 13 14 15

5 6 7 8

16 17 18 19

9 10 11

20 21 22

23 24 25 26 27 28 29 30 31 32 33

35

34

37

36

39

38

41

40

43

42

44

45

47

46

49

48

51

50

53

52

54

T6

SBF-5

*

1

*

2

1
1

*

*

2
2

C4

B4

B30

B1

B134

T6

B134

5

6

7

8

2

1

9

4

3

10

24

22 23

25

11 12 13 14 15

26 27

28

16 17

18 19 20 21

33 34

29

32

30 31

A:

B135

B:

B136

C:

B137

D:

A:

D2

A5

D3

E2

B21

E

35

34

40

D7

36

D1

37

1 2
3 4

3

1

4

MAIN RELAY

REAR
OXYGEN SENSOR

BATTERY

ECM

: TERMINAL No. OPTIONAL 
  ARRANGEMENT

: TERMINAL No. OPTIONAL 
  ARRANGEMENT 
  AMONG 1, 2, 5  AND 6

EN(H4DOTC)(diag)-142

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK REAR OXYGEN SENSOR DATA.
1) Warm up the engine until engine coolant 
temperature is above 75°C (167°F), and keep 
the engine speed at 3,000 rpm. (for up to 2 min-
utes)
2) Read the data of rear oxygen sensor signal 
using Subaru Select Monitor or general scan 
tool.

NOTE:
• Subaru Select Monitor
For detailed operation procedure, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H4DOTC)(diag)-34, Subaru Select Moni-
tor.>
• General scan tool
For detailed operation procedures, refer to the
general scan tool operation manual.

Is the voltage 490 mV or more? Go to step 5.

Go to step 2.

2

CHECK REAR OXYGEN SENSOR CONNEC-
TOR AND COUPLING CONNECTOR.

Has water entered the connec-
tor?

Completely 
remove any water 
inside.

Go to step 3.

3

CHECK HARNESS BETWEEN ECM AND 
REAR OXYGEN SENSOR CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM and 
rear oxygen sensor.
3) Measure the resistance of harness between 
ECM and rear oxygen sensor connector.

Connector & terminal

(B135) No. 4 — (T6) No. 3:
(B135) No. 30 — (T6) No. 4:

Is the resistance less than 1 

:? Go to step 4.

Repair the harness 
and connector.

NOTE:
In this case, repair
the following item:
• Open circuit in
harness between
ECM and rear oxy-
gen sensor con-
nector
• Poor contact of
coupling connector

4

CHECK HARNESS BETWEEN ECM AND 
REAR OXYGEN SENSOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from rear oxygen 
sensor.
3) Turn the ignition switch to ON.
4) Measure the voltage between rear oxygen 
sensor connector and chassis ground.

Connector & terminal

(T6) No. 3 (+) — Chassis ground (–):

Is the voltage 0.2 — 0.5 V?

Replace the rear 
oxygen sensor. 
<Ref. to 
FU(H4DOTC)-48, 
Rear Oxygen Sen-
sor.>

Repair the harness 
and connector.

NOTE:
In this case, repair
the following item:
• Open circuit of
harness between
the ECM and rear
oxygen sensor
• Poor contact of
the rear oxygen
sensor connector
• Poor contact in
ECM connector

5

CHECK EXHAUST SYSTEM.
Check exhaust system parts.

NOTE:
Check the following items.
• Looseness and improper attachment of ex-
haust system parts
• Damage (crack, hole etc.) of parts
• Looseness and improper attachment of parts
between front oxygen (A/F) sensor and rear ox-
ygen sensor

Is there any fault in exhaust 
system?

Repair or replace 
faulty parts.

Replace the rear 
oxygen sensor. 
<Ref. to 
FU(H4DOTC)-48, 
Rear Oxygen Sen-
sor.>

EN(H4DOTC)(diag)-143

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

AE:DTC P0138 O2 SENSOR CIRCUIT HIGH VOLTAGE (BANK 1 SENSOR 2)

DTC DETECTING CONDITION:
• Two consecutive driving cycles with fault
• GENERAL DESCRIPTION <Ref. to GD(H4DOTC)-57, DTC P0138 O2 SENSOR CIRCUIT HIGH VOLT-
AGE (BANK 1 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Criteria.>

CAUTION:
After repair or replacement of faulty parts, perform Clear Memory Mode <Ref. to EN(H4DOTC)(diag)-
52, OPERATION, Clear Memory Mode.>, and Inspection Mode <Ref. to EN(H4DOTC)(diag)-43, PRO-
CEDURE, Inspection Mode.>.
WIRING DIAGRAM:

EN-05670

B83

1 2 3 4
5 6 7 8

B138

B47

1

2

4

6

3

5

E

*

*

B138

B83

3

4

1

2

5

6

B135

B47

B19

B136

B:

C:

B137

D:

5

6

7 8

2

1

9

4

3

10

24

22 23

25

11 12 13 14 15

26 27

28

16

17 18 19 20 21

33 34

29

32

30

31

35

5

6

7

8

2

1

9

4

3

10

24

22 23

25

11 12 13 14 15

26 27

28

16 17 18 19

20 21

29 30 31

32 33

34 35

5

6

7

8

2

1

9

4

3

10

22 23

11 12 13 14 15

24 25

26

16 17

18 19 20 21

27

28 29

30 31

B19

T5

2

2

T5

B19

3

1

4

B21

1 2 3 4

12 13 14 15

5 6 7 8

16 17 18 19

9 10 11

20 21 22

23 24 25 26 27 28 29 30 31 32 33

35

34

37

36

39

38

41

40

43

42

44

45

47

46

49

48

51

50

53

52

54

T6

SBF-5

*

1

*

2

1
1

*

*

2
2

C4

B4

B30

B1

B134

T6

B134

5

6

7

8

2

1

9

4

3

10

24

22 23

25

11 12 13 14 15

26 27

28

16 17

18 19 20 21

33 34

29

32

30 31

A:

B135

B:

B136

C:

B137

D:

A:

D2

A5

D3

E2

B21

E

35

34

40

D7

36

D1

37

1 2
3 4

3

1

4

MAIN RELAY

REAR
OXYGEN SENSOR

BATTERY

ECM

: TERMINAL No. OPTIONAL 
  ARRANGEMENT

: TERMINAL No. OPTIONAL 
  ARRANGEMENT 
  AMONG 1, 2, 5  AND 6

EN(H4DOTC)(diag)-144

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK REAR OXYGEN SENSOR DATA.
1) Warm up the engine until engine coolant 
temperature is above 75°C (167°F), and rapidly 
reduce the engine speed from 3,000 rpm.
2) Read the data of rear oxygen sensor signal 
using Subaru Select Monitor or general scan 
tool.

NOTE:
• Subaru Select Monitor
For detailed operation procedure, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H4DOTC)(diag)-34, Subaru Select Moni-
tor.>
• General scan tool
For detailed operation procedures, refer to the
general scan tool operation manual.

Is the voltage 250 mV or less?

Go to step 5.

Go to step 2.

2

CHECK REAR OXYGEN SENSOR CONNEC-
TOR AND COUPLING CONNECTOR.

Has water entered the connec-
tor?

Completely 
remove any water 
inside.

Go to step 3.

3

CHECK HARNESS BETWEEN ECM AND 
REAR OXYGEN SENSOR CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM and 
rear oxygen sensor.
3) Measure the resistance of harness between 
ECM and rear oxygen sensor connector.

Connector & terminal

(B135) No. 4 — (T6) No. 3:
(B135) No. 30 — (T6) No. 4:

Is the resistance less than 1 

:? Go to step 4.

Repair the harness 
and connector.

NOTE:
In this case, repair
the following item:
• Open circuit in
harness between
ECM and rear oxy-
gen sensor con-
nector
• Poor contact of
coupling connector

4

CHECK HARNESS BETWEEN ECM AND 
REAR OXYGEN SENSOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from rear oxygen 
sensor.
3) Turn the ignition switch to ON.
4) Measure the voltage between rear oxygen 
sensor connector and chassis ground.

Connector & terminal

(T6) No. 3 (+) — Chassis ground (–):

Is the voltage 0.2 — 0.5 V?

Replace the rear 
oxygen sensor. 
<Ref. to 
FU(H4DOTC)-48, 
Rear Oxygen Sen-
sor.>

Repair the harness 
and connector.

NOTE:
In this case, repair
the following item:
• Open circuit of
harness between
the ECM and rear
oxygen sensor
• Poor contact of
the rear oxygen
sensor connector
• Poor contact in
ECM connector

5

CHECK EXHAUST SYSTEM.
Check exhaust system parts.

NOTE:
Check the following items.
• Looseness and improper attachment of ex-
haust system parts
• Damage (crack, hole etc.) of parts
• Looseness and improper attachment of parts
between front oxygen (A/F) sensor and rear ox-
ygen sensor

Is there any fault in exhaust 
system?

Repair or replace 
faulty parts.

Replace the rear 
oxygen sensor. 
<Ref. to 
FU(H4DOTC)-48, 
Rear Oxygen Sen-
sor.>