Двигатели Scania четвёртой серии. Руководство - часть 157

 

  Главная      Автомобили - Scania     Двигатели Scania 4-ой серии - руководство по эксплуатации и ремонту

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  155  156  157  158   ..

 

 

Двигатели Scania четвёртой серии. Руководство - часть 157

 

 

66

ã

03:04-06

Fault code D002

Fault

Internal fault in the control unit.

Cause

The control unit could not process (convert) the 
signal from the fuel supply pressure sensor.

Remarks

If the fault is active, the control unit uses a pre-
programmed value (21,4 bar absolute 
pressure).

Engine torque is limited by 30% as long as the 
fault is active.

Action

Clear the fault code memory. Start the engine 
and accelerate the engine to full speed.

If the fault code is regenerated, renew the 
control unit.

Fault codes

03:04-06

ã

67

Fault code D004

Fault

The control unit does not rely on the fuel 
supply pressure sensor signal even though it is 
within the electrical tolerances.

Cause

The supply pressure is implausibly high in 
comparison with normal pressure for different 
operational conditions.

Remarks

If the voltage is outside the permitted range, the 
control unit uses a pre-programmed value 
(21,4 bar absolute pressure).

Engine torque is limited by approximately 30% 
as long as the fault is active.

Action

Check the overflow valve.

Check the signal from the fuel feed pressure 
sensor.

Check for any visible faults on the sensor and 
the wiring.

Clean the connectors.

Then, erase the fault code memory and check 
whether the fault code is generated again.

Fault codes

68

ã

03:04-06

Fault code D005

Fault

The control unit does not rely on the fuel 
supply pressure sensor signal even though it is 
within the electrical tolerances.

Cause

The supply pressure is implausibly low in 
comparison with normal pressure for different 
operational conditions.

Remarks

If the voltage is outside the permitted range, the 
control unit uses a pre-programmed value 
(21,4 bar absolute pressure).

Engine torque is limited by approximately 30% 
as long as the fault is active.

Action

Check the signal from the fuel supply pressure 
sensor.

Check for any visible faults on the sensor and 
the wiring.

Clean the connectors.

Then, erase the fault code memory and check 
whether the fault code is generated again.

The fault may also be due to any of the 
following causes:

One of the two overflow valves opens too early.

The fuel shut-off valve is closed.

The fuel filter is blocked.

Air in the fuel or out of fuel.

Defect supply pump.

Serious leakage in the fuel system.

Fault codes

03:04-06

ã

69

Fault code D100

Fault

The voltage has been above 4.79 V (above 
20.3 bar absolute pressure), i.e. above the upper 
limit for the fuel pressure to the front bank, 
cylinder 1-3.

Cause

The voltage between pin 3 and 2 in connector 
A1 is too high, or there is a fault with the 
voltage supply to sensor group 2 (pin 8 in 
connector B2, pin 1 in connector A1).

Remarks

If the voltage is outside the permitted range, the 
control unit uses a pre-programmed value 
(0.448 bar absolute pressure).

If the value from the fuel pressure sensor for 
the rear bank, cylinder 4-6 is incorrect at the 
same time, it is probably the shared voltage 
supply for the sensors which is faulty.

Engine torque is limited by 30% as long as the 
fault is active.

Action

Check the signal from the fuel pressure sensor.

Check for any visible faults on the sensor and 
the wiring.

Clean the connectors.

Then, erase the fault code memory and check 
whether the fault code is generated again.

Fault codes

 

 

 

 

 

 

 

содержание   ..  155  156  157  158   ..