Peugeot 2008 (2024 year). Manual in english

Practical information

► Remove the cap from the lock and press it

► Release the wheel; it automatically locks in

Maximum load distributed over the roof

onto the head of the key.

the unlocked position (position B).

bars, for a loading height not exceeding

40 cm: 70 kg.

As this value may change, please verify the

maximum load quoted in the guide supplied

with the roof bars.

If the height exceeds 40 cm, adapt the speed

of the vehicle to the profile of the road to

avoid damaging the roof bars and the fixings

on the vehicle.

Be sure to refer to national legislation in order

to comply with the regulations for transporting

objects that are longer than the vehicle.

► Insert the key into the lock 7.

► Replace the protective plug 2 into the

► Open the lock using the key.

carrier 1.

Recommendations

► Stow the towball in its bag to protect it from

Distribute the load uniformly, taking care

knocks and dirt.

to avoid overloading one of the sides.

Arrange the heaviest part of the load as close

as possible to the roof.

Roof bars

Secure the load firmly.

Drive gently: the vehicle will be more

As a safety measure and to avoid

susceptible to the effects of side winds and its

damaging the roof, it is essential to use

stability may be affected.

transverse roof bars approved for your

Regularly check the security and tight

vehicle.

fastening of the roof bars, at least before each

Observe the instructions on fitting and use

trip.

contained in the guide supplied with the roof

Remove the roof bars once they are no longer

► Hold the towball 5 firmly in one hand; using

bars.

needed.

the other hand, pull and turn the wheel 6 fully in

a clockwise direction until it stops; do not release

Sunroof

the wheel.

Check that the load does not protrude

► Extract the towball from the base of its

below the roof bars, so that it does not

carrier 1.

161

CarManuals2.com

Practical information

impede movement of the sunroof - risk of

The roof bar fixings have a stud which must be

Installation tips

major damage!

inserted into the opening of each anchorage

► To fit the snow chains during a journey, stop

point.

the vehicle on a flat surface at the side of the

Fitting on longitudinal bars

road.

Snow chains

► Apply the parking brake and position any

wheel chocks under the wheels to prevent

In wintry conditions, snow chains improve

movement of the vehicle.

traction as well as the behaviour of the vehicle

► Fit the snow chains following the instructions

when braking.

provided by the manufacturer.

Snow chains must be fitted only to the

► Move off gently and drive for a few moments,

front wheels.

without exceeding 31 mph (50 km/h).

They must never be fitted to "space-saver"

► Stop the vehicle and check that the snow

The transverse bars must be fixed at the

type spare wheels.

chains are correctly tightened.

markings located on the longitudinal bars.

It is strongly recommended that you

Observe the legislation in force in your

practise fitting the snow chains on a level

Direct fitting on roof

country relating to the use of snow

and dry surface before setting off.

chains and maximum authorised speeds.

Only use chains that have been designed to be

Avoid driving with snow chains on roads

fitted on the type of wheel on the vehicle:

that have been cleared of snow to avoid

damaging the vehicle's tyres and the road

Original tyre size

Maximum link size

surface. If the vehicle is fitted with alloy

215/65R16

9 mm (Polaire XP9)

wheels, check that no part of the chain or its

fixings is in contact with the wheel rim.

215/60R17

9 mm (Polaire XP9)

215/55R18

10 mm

(Polaire 0112)

Very cold climate screen

For more information on snow chains, contact a

(Depending on country of sale)

The transverse bars must only be fixed at the

PEUGEOT dealer or a qualified workshop.

This removable device prevents the

four anchorage points located on the roof frame.

accumulation of snow around the radiator

These points are concealed by the vehicle doors

cooling fan.

when the doors are closed.

162

CarManuals2.com

Practical information

It consists of a first element for the upper part

► First insert the lower fixing brackets into the

► Press the upper fixing brackets to release

of the front grille and a second element for the

bumper.

them from the grille.

lower part.

► Tilt the side screen upwards until the side and

► Gently tilt the central screen downwards.

then upper fixing brackets click into the bumper.

► Pull towards you to unclip the unit.

In case of difficulty with installation/

► Check that the unit is firmly held by pressing

removal

around the edges.

Contact a PEUGEOT dealer or a qualified

Repeat the same process to fit the central

workshop.

screen into the upper grille of the bumper.

Before any operation, ensure that the

Removing

engine is off and the cooling fan has

stopped.

It is essential to remove them when:

- the outside temperature exceeds

For the central screen with vertical grille

10°C.

► Insert a flat screwdriver into the holes to

- recovery is in progress.

reach the upper fixing brackets of the central

- the speed is above 75 mph (120 km/h).

screen.

► Press on each upper fixing bracket in turn to

For the side screen

release them from the grille.

Fitting

► Insert a finger into the notch in the lower part

► Pull towards you to unclip the unit.

of the side screen.

► Pull towards you to unclip the unit.

Energy economy mode

This system manages the duration of use of

certain functions, in order to conserve a sufficient

level of charge in the battery with the ignition off.

After switching off the engine and for a maximum

cumulative period of around 30 minutes, you can

continue to use functions such as the audio and

telematics system, dipped beam headlamps or

► Hold the side screen in front of the lower left

courtesy lamps.

grille of the bumper.

For the central screen with horizontal grille

163

CarManuals2.com

Practical information

Selecting the mode

Load reduction mode

Before carrying out any work under the

bonnet, you must switch off the ignition, check

A confirmation message is displayed when

This system manages the use of certain

that the READY indicator lamp is off on the

energy economy mode is entered, and the active

functions according to the level of charge

instrument panel and disconnect the nozzle

functions are placed on standby.

remaining in the battery.

from the charging connector if it is connected.

If a telephone call is in progress at the

When the vehicle is being driven, the load

time, it will be maintained for around 10

reduction function temporarily deactivates certain

minutes via the audio system’s hands-free

functions, such as the air conditioning and the

system.

heated rear screen.

The deactivated functions are reactivated

automatically as soon as conditions permit.

Exiting the mode

The location of the interior bonnet

These functions are automatically reactivated the

Bonnet

release lever prevents the bonnet being

next time the vehicle is used.

opened when the left-hand front door is

To restore the use of these functions

Stop & Start

closed.

immediately, start the engine and let it run:

Before doing anything under the bonnet,

- For less than 10 minutes, to use the

you must switch off the ignition to avoid any

When the engine is hot, handle the

equipment for approximately 5 minutes.

risk of the engine restarting automatically.

exterior safety catch and the bonnet stay

- For more than 10 minutes, to use the

Take care with objects or clothing that could

with care (risk of burns), using the protected

equipment for approximately 30 minutes.

be caught in the blades of the cooling fan

area.

Let the engine run for the specified duration to

or in certain moving components - risk of

When the bonnet is open, take care not to

ensure that the battery charge is sufficient.

strangulation and serious injury!

damage the safety catch.

To recharge the battery, avoid repeatedly or

Do not open the bonnet under very windy

continuously restarting the engine.

conditions.

A flat battery prevents the engine from

starting.

Cooling of the engine when stopped

For more information on the 12 V battery,

The engine cooling fan may start after

refer to the corresponding section.

Electric motor

the engine has been switched off.

Take care with objects or clothing that

could be caught in the blades of the cooling

could be caught in the blades of the fan!

fan or in certain moving components - risk of

strangulation and serious injury!

164

CarManuals2.com

Practical information

Opening

Closing

Diesel engine

► Open the left-hand front door.

► Hold the bonnet and pull out the stay from the

support slot.

► Clip the stay in its housing.

► Lower the bonnet and release it near the end

of its travel.

► Pull on the bonnet to check that it is locked

correctly.

1. Screenwash fluid reservoir

Because of the presence of electrical

2. Engine coolant reservoir

equipment under the bonnet, it is strongly

3. Brake fluid reservoir

recommended that exposure to water (rain,

4. Battery/Fuses

► Pull the interior release lever, located at the

washing, etc.) be limited.

5. Fusebox

bottom of the door frame, towards you.

6. Air filter

Engine compartment

7. Engine oil filler cap

8. Engine oil dipstick

The engine shown here is an example for

illustrative purposes only.

Diesel fuel system

The locations of the following components may

This system is under very high pressure.

vary:

All work must be carried out only by a

- Air filter.

PEUGEOT dealer or a qualified workshop.

- Engine oil dipstick.

- Engine oil filler cap.

Electric motor

Petrol engine

► Lift the exterior safety catch and raise the

bonnet.

► Unclip the stay from its housing and place it

in the support slot to hold the bonnet open.

1. Screenwash fluid reservoir

2. Engine coolant reservoir (level only)

165

CarManuals2.com

Practical information

Used products

Checking using the dipstick

3. Brake fluid reservoir

4. Battery/Fuses

For the location of the dipstick, please refer

Avoid prolonged contact of used oil or

5. Fusebox

to the illustration of the corresponding engine

fluids with the skin.

400 V electrical circuit

compartment.

Most of these fluids are harmful to health and

7. Emergency circuit-breaker for emergency

► Grasp the dipstick by its coloured grip and

very corrosive.

services and maintenance technicians

pull it out completely.

► Wipe the end of the dipstick using a clean,

For more information on the Charging system

Do not discard used oil or fluids into

lint-free cloth.

(Electric), refer to the corresponding section.

sewers or onto the ground.

Empty used oil into the containers reserved

for this purpose at a PEUGEOT dealer or a

Checking levels

qualified workshop.

Check all of the following levels regularly in

accordance with the Manufacturer's service

schedule. Top them up if required, unless

Engine oil

otherwise indicated.

The level is checked, with the engine

► Reinsert the dipstick and push fully down,

If a level drops significantly, have the

having been switched off for at least 30

then pull it out again to visually check the oil

corresponding system checked by a PEUGEOT

minutes and on level ground, either using the oil

level: the correct level is between marks A (max)

dealer or a qualified workshop.

level indicator in the instrument panel when the

and B (min).

ignition is switched on (for vehicles equipped

Do not start the engine if the level is:

The fluids must comply with the

with an electric gauge), or using the dipstick.

- above mark A: contact a PEUGEOT dealer or

Manufacturer's requirements and with

It is normal to top up the oil level between two

a qualified workshop.

the vehicle's engine.

services (or oil changes). It is recommended

- below mark B: top up the engine oil

that you check the level, and top up if necessary,

immediately.

Take care when working under the

every 3,000 miles (5,000 km).

bonnet, as certain areas of the engine

Oil grade

may be extremely hot (risk of burns) and the

In order to maintain the reliability of the

Before topping up or changing the

cooling fan could start at any time (even with

engine and emissions control system,

engine oil, check that the oil is suitable

the ignition off).

never use additives in the engine oil.

for your engine and complies with the

recommendations in the service schedule

supplied with the vehicle (or available

from your PEUGEOT dealer or qualified

workshop).

166

CarManuals2.com

Practical information

Use of non-recommended oil may invalidate

Engine coolant

If the level is close to or below

your warranty in the event of engine failure.

the "MIN" mark, it is essential to contact a

(Petrol or Diesel)

PEUGEOT dealer or a qualified workshop.

It is normal to top up this fluid between

Topping up the engine oil level

two services.

For the location of the engine oil filler cap, please

Screenwash fluid

The check and top-up must only be done with

refer to the corresponding engine compartment

Top up to the required level when

the engine cold.

illustration.

necessary.

A level of coolant that is too low risks causing

► Add oil in small quantities, avoiding any spills

major damage to the engine; the coolant level

on engine components (risk of fire).

Fluid specification

must be close to the "MAX" mark without ever

► Wait a few minutes before checking the level

The fluid must be topped up with a pre-mixed

going above it.

again using the dipstick.

product.

If the level is close to or below the "MIN" mark, it

► Top up the level if necessary.

In winter (temperatures below zero), a fluid

is essential to top it up.

► After checking the level, carefully screw the

containing an anti-freeze agent which is

When the engine is hot, the temperature of the

oil filler cap back on and replace the dipstick in

appropriate for the temperature conditions

coolant is regulated by the fan.

its tube.

must be used in order to protect the system's

As the cooling system is pressurised, wait at

least one hour after switching off the engine

components (pump, tank, ducts, jets).

The oil level indication displayed on the

instrument panel when the ignition is

before carrying out any work.

Filling with pure water is prohibited in all

switched on is not valid for 30 minutes

In order to avoid the risk of scalding if you need

circumstances (risk of freezing,

following an addition of oil.

to top up in an emergency, wrap a cloth around

limescale, etc.).

the cap and unscrew the cap by two turns to

allow the pressure to drop.

Brake fluid

Once the pressure has dropped, remove the cap

AdBlue^® (BlueHDi)

The level of this fluid should be close to

and top up to the required level.

An alert is triggered when the reserve level is

the "MAX" mark. If not, check the brake

reached.

Vehicle with electric motor

pads for wear.

For more information on the Indicators and in

Do not top up the coolant.

To know how often the brake fluid should be

particular the AdBlue range indicators, refer to

replaced, refer to the manufacturer's servicing

the corresponding section.

schedule.

To avoid the vehicle being immobilised in

accordance with regulations, you must top up the

Clean the cap before removing it to refill.

AdBlue tank.

Use only DOT4 brake fluid from a sealed

container.

167

CarManuals2.com

Practical information

For more information on AdBlue^® (BlueHDi),

Versions equipped with Stop & Start are

temporary lighting of this warning lamp,

and in particular the supply of AdBlue, refer to

fitted with a 12 V lead-acid battery with

accompanied by an alert message.

the corresponding section.

special technology and specifications.

As soon as traffic conditions allow, regenerate

Its replacement should be carried out only by

the filter by driving at a speed of at least

a PEUGEOT dealer or a qualified workshop.

37 mph (60 km/h), with an engine speed above

Checks

2,500 rpm, for about 15 minutes (until the

Unless otherwise indicated, check these

warning lamp goes out).

Passenger compartment

components in accordance with the

If it is not possible to reach 37 mph (60 km/h),

Manufacturer's service schedule and according

filter

leave the engine running at idle for about 15

to your engine.

minutes, then drive with an engine speed above

Depending on the environment and the

Otherwise, have them checked by a PEUGEOT

2,500 rpm for 15 minutes.

use of the vehicle (e.g. dusty atmosphere,

dealer or a qualified workshop.

city driving), change it twice as often, if

Do not switch off the engine until the filter

Only use products recommended by

necessary.

is fully regenerated; repeated intervals

PEUGEOT or products of equivalent

can degrade the engine oil prematurely.

A clogged passenger compartment filter

quality and specification.

Regenerating the filter while the vehicle is

can adversely affect air conditioning

In order to optimise the operation of

stationary is not recommended.

system performance and generate

components as important as those in the

undesirable odours.

braking system, PEUGEOT selects and offers

Following prolonged operation of the

very specific products.

vehicle at very low speed or at idle, you

Air filter

may, in exceptional circumstances, notice

Depending on the environment and the

water vapour coming from the exhaust while

12 V battery

use of the vehicle (e.g. dusty atmosphere,

accelerating. These emissions have no

The battery does not require any

city driving), change it twice as often, if

impact on the vehicle’s behaviour and the

maintenance.

necessary.

environment.

Check regularly that the terminals are correctly

tightened (versions without quick-release

Oil filter

New vehicle

terminals) and that the connections are clean.

Change the oil filter each time the engine

During the first few particle filter

For more information on the precautions

oil is changed.

regeneration operations, you may notice a

to take before any work on the 12 V

"burning" smell. This is perfectly normal.

battery, refer to the corresponding section.

Particle filter (Diesel)

The start of clogging of the

particle filter is indicated by the

168

CarManuals2.com

Practical information

Manual gearbox

necessary to have the condition of the brakes

Driving with worn or damaged tyres reduces the

checked, even between vehicle services.

braking and road holding performance of the

The gearbox does not require any

Unless there is a leak in the circuit, a drop in the

vehicle. Regularly check the condition of the

maintenance (no oil change).

brake fluid level indicates that the brake pads

tyres (tread and sidewalls) and rims as well as

are worn.

the presence of the valve caps.

Automatic gearbox

When the wear indicators no longer appear set

The gearbox does not require any

After washing the vehicle, moisture, or in

back from the tread, the depth of the grooves is

maintenance (no oil change).

wintry conditions, ice can form on the

less than 1.6 mm; replace the tyres as soon as

brake discs and pads: braking efficiency may

possible.

Manual parking brake

be reduced. Gently dab the brakes to dry and

Using different size wheels and tyres from those

If you notice excessive brake lever travel

defrost them.

specified can affect the lifetime of tyres, wheel

or decreased effectiveness, the parking

rotation, ground clearance, the speedometer

brake must be adjusted, even between two

Brake disc/drum wear

reading and have an adverse effect on road

services.

holding.

For any information on checking brake

This system must be checked by a PEUGEOT

Fitting different tyres on the front and rear axles

disc/drum wear, contact a PEUGEOT

dealer or a qualified workshop.

can cause the ESC to mistime.

dealer or a qualified workshop.

Always mark the direction of rotation on the tyres

Electric parking brake

Wheels and tyres

that will be stored when fitting winter or summer

This system does not require any routine

tyres. Store them in a cool, dry place and away

The inflation pressure of all tyres,

servicing. However, in the event of a

from direct exposure to the sun's rays.

including the spare wheel, must be

problem, do not hesitate to have the system

Winter or 4-seasons tyres can be

checked on "cold" tyres.

checked by a PEUGEOT dealer or a qualified

identified by this symbol on their

The pressures indicated on the tyre pressure

workshop.

sidewalls.

label are valid for "cold" tyres. If you have driven

For more information on the Electric

for more than 10 minutes or more than 6 miles

Shock absorbers

parking brake, refer to the

(10 kilometres) at over 31 mph (50 km/h), add

corresponding section.

It is not easy for drivers to detect when

0.3 bar (30 kPa) to the values indicated on the

shock absorbers are worn. Nevertheless,

label.

the shock absorbers have a major impact on

Brake pads

Under-inflation increases energy

road holding and braking performance.

Brake wear depends on the style of

consumption. Non-compliant tyre

For your safety and driving comfort, it is

driving, particularly in the case of vehicles

pressures cause tyres to wear prematurely

important to have them regularly checked by a

used in town, over short distances. It may be

and have an adverse effect on the vehicle's

PEUGEOT dealer or a qualified workshop.

road holding - risk of accident!

169

CarManuals2.com

Practical information

Timing and accessory kits

alert, which may vary considerably depending

The SCR system includes a heater for the

on your driving style.

AdBlue^® tank, allowing you to continue driving

The timing and accessory kits are used

An alert system is triggered once the reserve

in very cold conditions.

from the time the engine is started until it

level is reached: it is then possible to drive for a

is switched off. It is normal for them to wear over

further 1,500 miles (2,400 km) before the tank is

time.

Supply of AdBlue^®

empty and the vehicle is immobilised.

A faulty timing or accessory kit can damage

It is recommended that the AdBlue^® be topped

the engine, rendering it unusable. Observe the

For more information on the Warning

up as soon as the first alert is issued indicating

recommended replacement frequency, stated in

and indicator lamps and the associated

that the reserve level has been reached.

distance travelled or time elapsed, whichever is

alerts, or the Indicators, please refer to the

reached first.

corresponding sections.

For the correct operation of the SCR

system:

- Use only AdBlue^® fluid that meets the ISO

AdBlue^® (BlueHDi)

Once the AdBlue^® tank is empty, a device

22241 standard.

required by law prevents the engine from

To respect the environment and ensure

- Never transfer AdBlue^® to another container

being restarted.

compliance with the Euro 6 standard, without

as it would lose its purity.

If the SCR system is faulty, the level of

adversely affecting the performance or fuel

- Never dilute AdBlue^® with water.

emissions from the vehicle will no longer meet

consumption of its Diesel engines, PEUGEOT

the Euro 6 standard and the vehicle starts

has taken the decision to equip its vehicles with

You can obtain AdBlue^® from a PEUGEOT

polluting the environment.

dealer or a qualified workshop, as well as service

a system that combines SCR (Selective Catalytic

In the event of a confirmed SCR system

stations equipped with AdBlue^® pumps specially

Reduction) with a Diesel Particle Filter (DPF) for

malfunction, it is essential to visit a

designed for passenger vehicles.

the treatment of exhaust gases.

PEUGEOT dealer or a qualified workshop as

soon as possible. After 685 miles (1,100 km),

Recommendations on storage

SCR system

a device is automatically activated to prevent

AdBlue^® freezes at about -11°C and deteriorates

Using a liquid called AdBlue^® that contains

the engine from starting.

above +25°C. Containers should be stored in a

urea, a catalytic converter turns up to 85% of

In both cases, a range indicator indicates

cool area and protected from direct sunlight.

the nitrogen oxides (NOx) into nitrogen and

the distance that can be travelled before the

Under these conditions, the fluid can be kept for

water, which are harmless to health and the

vehicle is immobilised.

at least a year.

environment.

If the fluid has frozen, it can be used once it has

The AdBlue^® is contained in a special

Freezing of the AdBlue^®

completely thawed out at room temperature.

tank holding about 15 litres.

AdBlue^® freezes at temperatures below

Its capacity allows a driving range of

Never store AdBlue^® containers in your

around -11°C.

approximately 4,000 miles (6,500 km) before an

vehicle.

170

CarManuals2.com

Practical information

Precautions for use

Never pour the AdBlue^® into the Diesel

AdBlue^® is a urea-based solution. This fluid is

fuel tank.

non-flammable, colourless and odourless (when

kept in a cool place).

If any AdBlue^® is splashed, or if there are

In the event of contact with the skin, wash the

any spillages on the bodywork, rinse

affected area with soap and running water. In the

immediately with cold water or wipe with a

event of contact with the eyes, immediately rinse

damp cloth.

the eyes with large amounts of water or with an

If the fluid has crystallised, clean it off using a

eye wash solution for at least 15 minutes. Seek

sponge and hot water.

medical attention if you feel a persistent burning

► Turn the blue cap of the AdBlue^® tank anti-

sensation or irritation.

Important: in the event of a top-up after

clockwise and remove it.

If swallowed, immediately wash out the mouth

a breakdown because of a lack of

► With a container of AdBlue^®: after checking

with clean water and then drink plenty of water.

AdBlue, it is essential to wait around 5

the expiry date, read the instructions on the

In certain conditions (high temperature, for

minutes before switching on the ignition,

label carefully before pouring the contents of the

example), the risk of release of ammonia cannot

without opening the driver’s door,

container into the vehicle's AdBlue^® tank.

be excluded: do not inhale the fluid. Ammonia

unlocking the vehicle, inserting the key

► With an AdBlue^® pump: insert the nozzle and

vapours have an irritant effect on mucous

into the ignition switch, or bringing the

fill the tank until the nozzle automatically cuts

membranes (eyes, nose and throat).

key for the "Keyless Entry and Start"

out.

system into the passenger compartment.

Store AdBlue^® out of the reach of

In order not to overfill the AdBlue^® tank:

Switch on the ignition, then wait for 10

children, in its original container.

- Add between 10 and 13 litres using

seconds before starting the engine.

AdBlue^® containers.

Procedure

► Switch off the ignition and remove the key

- Stop after the nozzle’s first automatic cut-

from the switch to switch off the engine.

out, if you are refilling at a service station.

Before starting the top-up procedure, ensure that

The system only registers AdBlue^®

the vehicle is parked on a flat and level surface.

► With the Keyless Entry and Start system,

intermediate top-ups of 5 litres or more.

In wintry conditions, ensure that the temperature

press the "START/STOP" button to switch off the

of the vehicle is above -11°C. Otherwise the

engine.

If the AdBlue^® tank is completely empty

AdBlue^® may be frozen and so cannot be poured

into the tank. Park the vehicle in a warmer area

- which is confirmed by the message

for a few hours to allow the top-up to be carried

out.

171

CarManuals2.com

Practical information

“Top up AdBlue: Starting impossible” - it is

To release them

► Switch off the ignition.

essential to add at least 10 litres.

► With the engine running and while depressing

If the 5-second time limit is exceeded,

Top-up detection may not be instantaneous

the brake pedal, move the gear selector to the

the gearbox engages mode P; it is then

after addition. It may take a few minutes of

neutral position.

necessary to restart the procedure.

driving before the top-up detection is effective.

► While depressing the brake pedal, switch off

the engine.

Reverting to normal operation

► Release the brake pedal, then switch on the

► Press button P on the selector.

Free-wheeling

ignition.

► While depressing the brake pedal, press the

In certain situations, it is necessary to put the

With EAT8 automatic

control to release the parking brake.

vehicle into free-wheeling mode (e.g. towing, on

► Release the brake pedal, then switch off the

gearbox or drive selector

a rolling road, automatic car wash (Wash mode),

rail or sea transport).

ignition.

and electric parking brake

The procedure varies according to the type of

Reverting to normal operation

gearbox and parking brake.

► While depressing the brake pedal, restart the

Never leave the vehicle unattended with

engine and apply the parking brake.

Release procedure

the vehicle into free-wheeling mode.

► With the vehicle stationary and the engine

With EAT8 automatic

running, depress the brake pedal and select

Keyless Entry and Start

gearbox and manual parking

mode N.

You must not depress the brake pedal

brake

Within 5 seconds:

while switching the ignition on again, then

► Depress and hold the brake pedal, then

switching it off. If you do, the engine will start,

observe this order: switch off the engine and

requiring you to restart the procedure.

move the push selector forwards or backwards.

Release procedure

► Release the brake pedal, then switch on the

► With the vehicle stationary and the engine

ignition.

With manual or EAT6

running, select mode N and switch off the

► Place your foot on the brake and press the

automatic gearbox and

engine.

electric parking brake control to release it.

Within 5 seconds:

► Release the brake pedal, then switch off the

electric parking brake

► Switch on the ignition.

ignition.

► While depressing the brake pedal, move the

push selector forwards or backwards to confirm

mode N.

172

CarManuals2.com

Practical information

A message is displayed on the

to lock the doors and, depending on version,

To clean instrument panels, touch screens

instrument panel to confirm the unlocking

move the electronic key away.

or other displays, wipe gently with a soft,

of the wheels for 15 minutes.

When using a pressure washer, keep the jet

dry cloth. Do not use products (e.g. alcohol,

When the vehicle is free-wheeling, the

nozzle at a minimum distance of 30 cm from

disinfectant) or soapy water directly on these

audio system cannot be updated (message

the vehicle (particularly when cleaning areas

surfaces - risk of damage!

displayed on the instrument panel).

containing chipped paint, sensors or seals).

Promptly clean up any stains containing

Bodywork

After 15 minutes or reverting to normal

chemicals liable to damage the vehicle's

operation

paintwork (including tree resin, bird

High-gloss paint

droppings, insect secretions, pollen and tar).

► While depressing the brake pedal, restart the

Depending on the environment, clean the

Do not use abrasive products, solvents,

engine and select mode P.

vehicle frequently to remove salty deposits

petrol or oil to clean the bodywork.

(in coastal areas), soot (in industrial areas)

Never use an abrasive sponge to clean

Advice on care and

and mud/salts (in wet or cold areas). These

stubborn stains - risk of scratching the

substances can be highly corrosive.

paintwork!

maintenance

Contact a PEUGEOT dealer or a qualified

Do not apply polish in strong sunshine, or to

workshop for advice on removing stubborn

plastic or rubber parts.

General recommendations

stains requiring special products (such as tar

Observe the following recommendations to avoid

or insect removers).

Use a soft cloth and soapy water or a pH

damaging the vehicle.

Preferably, have paint touch-ups performed

neutral product.

Exterior

by a PEUGEOT dealer or a qualified

Gently wipe the bodywork with a clean

workshop.

microfibre cloth.

Never use a high-pressure jet wash in

Apply polish with the vehicle clean and dry.

the engine compartment - risk of

Interior

Comply with the instructions for use stated on

damaging the electrical components!

the product.

Do not wash the vehicle in bright sunshine or

When washing the vehicle, never use a

extremely cold conditions.

water hose or high-pressure jet to clean

Decals

the interior.

(Depending on version)

When washing the vehicle in an

Liquids carried in cups or other open

automatic roller-brush car wash, be sure

containers can spill, presenting a risk of

Do not use a high-pressure washer to

damage to the instruments and controls and

clean the vehicle - risk of damaging or

the controls located on the centre console. Be

detaching the decals!

vigilant!

173

CarManuals2.com

Practical information

Use a high-flow hose (temperature

Act quickly by reducing the stain from its

Do not use printed cloths or

between 25°C and 40°C).

edges inwards.

printed absorbent paper.

Place the jet of water perpendicular to the

Remove as much substance or solids as

Do not use steam-cleaning systems.

surface to be cleaned.

possible using a spoon or spatula, and

Rinse the vehicle with demineralised water.

remove as much liquid as possible using

Remove dust from the Alcantara^® parts

absorbent paper.

regularly with a dry cloth, soft brush or

vacuum cleaner.

Textile

Product/Procedure to use depending

Clean the Alcantara^®, without rubbing too

The dashboard, door panels and seats may

on the type of stain:

vigorously, with a white cotton cloth which is

contain parts made of textile material.

- Grease, oil and ink: clean with a pH-neutral

slightly damp.

Maintenance

detergent.

To find out which products and procedures to

- Vomit: clean with sparkling mineral water.

Do not use aggressive cleaning products

use on different types of stains, refer to the

- Blood: spread flour over the stain and allow

(e.g. alcohol, solvent or ammonia).

"Textile - Stain removal" section.

to dry; remove with a slightly damp cloth.

Do not use steam-cleaning systems - risk of

For more information, go to the Alcantara^®

- Mud: allow to dry and then remove with a

affecting the adhesion of the fabrics!

trademark website: www.alcantara.com.

slightly damp cloth.

- Cake, chocolate, ice cream: clean with

Leather

Remove dust from the textile parts

lukewarm water.

regularly with a dry cloth, soft brush or

- Sugary and/or alcoholic drinks: clean with

Leather is a natural product. Appropriate regular

vacuum cleaner.

lukewarm water, or lemon juice if the stain is

care is essential for its durability.

Rub down the textile parts once per year with

persistent.

It must be protected and nourished using a

a clean, damp cloth. After leaving overnight to

- Hair gel, coffee, tomato sauce, vinegar:

specific leather product, to keep it supple and

dry, brush with a soft-bristled brush.

clean with lukewarm water and lemon juice.

preserve its original appearance.

For solid substances, then use a soft brush or

Do not use maintenance products which

Stain removal

vacuum cleaner.

are not suitable for cleaning leather

For liquid substances, then use a damp

(e.g. solvent, detergent, petrol, pure alcohol).

Do not rub the stain or it may spread or

microfibre cloth and then dry with another

Do not use bleaching or colour-removal

you may cause the substance to

cloth.

products (e.g. perchloroethylene).

penetrate the surface.

When cleaning items partly made from

leather, take care not to damage the other

Alcantara^®

materials with the specific leather product.

Alcantara^® is an elegant and practical material

which is very resistant and easy to maintain.

174

CarManuals2.com

In the event of a breakdown

Warning triangle

Assembling and placing the

For more information on Refuelling and

on Misfuel prevention (Diesel), refer to

This reflective and dismantable device is to be

triangle

the corresponding section.

installed on the side of the road when a vehicle

is broken down or damaged.

1.5 BlueHDi engines

Before getting out of the vehicle

► Switch on the ignition (without starting the

Turn on the hazard warning lamps, then

engine).

put on the safety vest to assemble and install

► Wait around 1 minute and switch off the

the triangle.

ignition.

► Operate the starter motor to start the engine.

If the engine does not start at the first attempt,

Storage compartment

do not keep trying, but restart the procedure.

Tool kit

For versions supplied with a triangle as original

Set of tools supplied with the vehicle.

equipment, refer to the illustration above.

Its content depends on your vehicle's equipment:

For other versions, refer to the assembly

- Temporary puncture repair kit.

instructions provided with the triangle.

- Spare wheel.

► Put the triangle in place behind the vehicle,

as required by local legislation.

These tools are specific to the vehicle

and may vary according to the level of

equipment.

Running out of fuel

Do not use them for any other purpose.

(Diesel)

There is a compartment in the interior trim of the

tailgate to store a warning triangle.

With Diesel engines, the fuel system must be

Access to the tools

► After opening the tailgate, release the cover

primed if you run out of fuel.

Depending on version, the tool kit is stored in a

by turning the screw a quarter turn to the left.

Before starting to prime the system, it is

bag or in a storage box in the boot.

essential to put at least 5 litres of Diesel into the

fuel tank.

176

CarManuals2.com

In the event of a breakdown

► Raise the boot floor (depending on version),

With temporary puncture repair kit

then the boot carpet by pulling the strap to

access the tools.

List of tools

On the boot carpet or floor

12 V compressor with cartridge of sealant

and speed limit sticker

1. Chock to immobilise the vehicle (depending

For temporary repair of a tyre and to adjust

on equipment)

the tyre pressure.

2. Socket for the security bolts (located in the

For more information on the Temporary

glove box) (depending on equipment)

puncture repair kit, refer to the corresponding

To adapt the wheelbrace to the special

section.

‘security’ bolts.

3. Removable towing eye

With spare wheel

For more information on Towing the vehicle

and using the removable towing eye, refer to the

corresponding section.

Under the boot carpet or floor

5. Wheelbrace

For removing the wheel bolts.

177

CarManuals2.com

In the event of a breakdown

Tyre inflation pressures are indicated on

6. Jack with integrated handle

Temporary puncture

this label.

To raise the vehicle.

repair kit

For more information on Identification

7. Wheel bolt cap removal tool

markings, particularly this label, refer to the

For removing the central bolt cover from alloy

Visit this link to view explanatory videos:

corresponding section.

wheels.

http://q-r.to/bagGl9

For more information on the Spare wheel, refer

to the corresponding section.

The jack must only be used to change a

wheel with a damaged or punctured tyre.

Should the pressure of one or more tyres

Do not use any jack other than the one

be adjusted, it is necessary to reinitialise

supplied with the vehicle.

Made up of a compressor and a sealant

the under-inflation detection system.

If the vehicle does not have its original jack,

cartridge, it allows you to carry out a temporary

For more information on Tyre under-inflation

contact a PEUGEOT dealer or a qualified

repair of the tyre so that you can drive to the

detection, refer to the corresponding section.

workshop to obtain the one that was intended

nearest garage.

by the manufacturer.

It is designed to repair most punctures located

The jack meets European standards,

on the tyre tread.

Repair procedure

as defined in the Machinery Directive

The vehicle's electric system allows the

Do not remove any foreign body

2006/42/CE, and also complies with UKCA

connection of the compressor to the 12 V

(e.g. nail, screw) which has penetrated

requirement, as defined by the Supply

power supply for long enough to repair a tyre

the tyre.

of Machinery (Safety) Regulations 2008

after a puncture.

No.1597.

► Park the vehicle without obstructing traffic

The jack does not require any maintenance.

and apply the parking brake.

For more information on the Tool kit,

► Follow the safety instructions (hazard

refer to the corresponding section.

warning lamps, warning triangle, high visibility

jacket, etc.) according to the legislation in force

in the country in which you are driving.

► Switch the ignition off.

► Remove the valve cap from the tyre to be

repaired, and place it in a clean place.

178

CarManuals2.com

In the event of a breakdown

After use, do not discard the bottle into the

environment; take it to a PEUGEOT dealer or

an authorised waste disposal site.

Do not forget to obtain a new bottle of

sealant, available from a PEUGEOT dealer or

a qualified workshop.

► Switch on the compressor by moving the

switch to position "I" until the tyre pressure

reaches 2 bar. The sealant product is injected

► Connect the pipe from the bottle of sealant to

under pressure into the tyre; do not disconnect

the valve of the tyre to be repaired and tighten

the pipe from the valve during this operation (risk

firmly.

of blowback).

► Uncoil the pipe stowed under the compressor.

If after approximately 7 minutes, the

► Connect the pipe from the compressor to the

pressure of 2 bar is not reached, this

bottle of sealant.

indicates that the tyre is not repairable;

► Check that the compressor switch is in

► Drive immediately for approximately 3 miles

contact a PEUGEOT dealer or a qualified

position "O".

(5 kilometres) at reduced speed (between

workshop for assistance.

► Fully uncoil the electric cable stowed under

12 and 37 mph (20 and 60 km/h)) to plug the

the compressor.

puncture.

► Move the switch to position "O".

► Connect the compressor's electric plug to the

► Stop to check the repair and the tyre

► Disconnect the compressor's electric plug

vehicle's 12 V socket.

pressure using the kit:

from the vehicle's 12 V socket.

• If the tyre pressure is incorrect, contact a

► Affix the speed limit sticker.

► Remove the kit.

PEUGEOT dealer to have the tyre changed.

► Refit the cap on the valve.

• If the tyre pressure is correct, drive a second

► Remove and store the bottle of sealant.

time for approximately 3 miles (5 kilometres)

The sealant product is harmful if

at reduced speed (between 12 and 37 mph

swallowed and causes irritation to the

(20 and 60 km/h)), stop then check again

The speed limit sticker must be affixed

eyes.

the tyre pressure using the kit to confirm the

inside the vehicle in the area close to the

Keep this product out of the reach of children.

effective repair of the tyre.

driver, to remind them that a wheel is in

The use-by date of the fluid is marked on the

temporary use.

With a tyre repaired using this type of kit,

bottle.

do not exceed a speed of 50 mph

► Switch the ignition on.

179

CarManuals2.com

In the event of a breakdown

(80 km/h) and do not drive more than

contact a PEUGEOT dealer or a qualified

Accessing the spare wheel

125 miles (200 km).

workshop for assistance.

You must contact a PEUGEOT dealer or a

► Once the correct pressure is reached, put the

qualified workshop to have the repair checked

switch in position "O".

and the tyre changed.

► Remove the kit and stow it.

► Refit the cap on the valve.

Checking/adjusting tyre

pressures

Spare wheel

The compressor can be used, without injecting

sealant, to check and, if necessary, adjust the

Visit this link to view explanatory videos:

tyre pressures.

http://q-r.to/bagGl9

The spare wheel is stored under the boot carpet.

► Remove the valve cap from the tyre and keep

To access the spare wheel, first refer to the Tool

it in a clean place.

kit section.

► Uncoil the pipe stowed under the compressor.

► Screw the pipe onto the valve and tighten

Depending on version, the spare wheel

firmly.

may be a standard steel, non-standard or

► Check that the compressor switch is in

'space-saver' wheel.

position "O".

For more information on the Tool kit,

► Fully uncoil the electric cable stowed under

refer to the corresponding section.

Removing the spare wheel

the compressor.

► Connect the compressor's electric plug to the

Spare wheel tyre pressure

vehicle's 12 V socket.

The inflation pressure for the spare

► Switch the ignition on.

wheel is indicated on the tyre pressure label

► Start the compressor by placing the switch at

- ensure that its inflation pressure is checked

position "I" and adjust the pressure to the value

regularly.

shown on the vehicle's tyre pressure label. To

For more information on Identification

deflate: press the black button located on the

markings, particularly the tyre pressure label,

compressor pipe, near the valve connection.

refer to the corresponding section.

► Slacken the central nut.

If after 7 minutes the pressure of 2 bar is

► Remove the fastening device (nut and bolt).

not reached, the tyre is damaged;

► Lift the spare wheel towards you from the

rear.

180

CarManuals2.com

In the event of a breakdown

► Take the wheel out of the boot.

unless it is set to automatic mode, and switch

off the ignition.

Putting the spare wheel back in place

With an automatic gearbox, select mode P

to lock the wheels, apply the parking brake,

The punctured wheel cannot be put

unless it is set to automatic mode, and switch

under the boot floor.

off the ignition.

Check that the parking brake indicator lamps

on the instrument panel are on fixed.

The occupants must get out of the vehicle

and wait where they are safe.

If necessary, place a chock under the wheel

diagonally opposite the wheel to be changed.

Never go underneath a vehicle raised using a

jack; use an axle stand.

► Put the spare wheel back in place in its

Wheel with wheel trim

housing.

When removing the wheel, first remove

► Slacken the nut on the bolt by a few turns.

the wheel trim by pulling at the valve aperture

► Position the fastening device (nut and bolt) in

using the wheelbrace.

the middle of the wheel.

When refitting the wheel, refit the wheel

► Tighten the central nut sufficiently to retain

trim, starting by placing its aperture in line

the wheel correctly.

with the valve and then pushing it into place

► Depending on version, put the tool box back

in place in the middle of the wheel and clip it in

all round its edge with the palm of your hand.

- If the vehicle has steel wheels, remove the

place.

wheel trim.

- If the vehicle has alloy wheels, remove the

Removing a wheel

central bolt cover using tool 7.

- If the vehicle is so equipped, fit security bolt

Parking the vehicle

socket 2 to wheelbrace 5 to slacken the security

Immobilise the vehicle where it does

bolt.

not obstruct traffic: the ground must be level,

- Slacken the other bolts using the

stable and non-slippery.

wheelbrace 5 only.

With a manual gearbox, engage first gear

to lock the wheels, apply the parking brake,

181

CarManuals2.com

In the event of a breakdown

Never use an impact wrench on the

► Raise the vehicle until there is sufficient

Fitting a wheel

security bolt socket.

space between the wheel and the ground to

easily admit the spare (not punctured) wheel.

Fitting a steel or "space-saver" type

spare wheel

Ensure that the jack is stable. If the

ground is slippery or loose, the jack may

slip or collapse - risk of injury!

Take care to position the jack strictly at

one of the jacking points A or B under the

vehicle, ensuring that the head of the jack is

centred under the contact area on the vehicle.

If the vehicle is fitted with alloy wheels, the

Otherwise, there is a risk of damage to the

washers A do not make contact with the steel

vehicle and/or of the jack collapsing - risk of

► Place the foot of jack 6 on the ground and

or "space-saver" type spare wheel. The wheel

injury!

ensure that it is directly below the front A or

is held in place by the conical contact surface

rear B jacking point on the underbody, whichever

B of each bolt.

is closest to the wheel to be changed.

► Remove the bolts and store them in a clean

place.

► Remove the wheel.

► Extend jack 6 until its head comes into

► Fit the wheel on the hub.

contact with jacking point A or B; contact area A

► Screw in the bolts by hand as far as possible.

or B on the vehicle must be properly inserted

► Pre-tighten the security bolt using the

into the central part of the head of the jack.

wheelbrace 5 equipped with a security socket 2.

► Pre-tighten the other bolts using the

wheelbrace 5 only.

182

CarManuals2.com

In the event of a breakdown

After changing a wheel

Changing a bulb

With a non-standard or 'space-saver'

In some weather conditions (e.g. low

spare wheel

temperature or humidity), misting on the

internal surface of the glass of the headlamps

and rear lamps is normal, and will disappear

after the lamps have been on for a few

minutes.

Deactivate certain driving aid functions

Never look too closely at the light beam

(Active Safety Brake, Adaptive cruise control,

of LED technology lamps - risk of serious

► Lower the vehicle again fully.

etc.).

eye injury!

► Fold jack 6 and remove it.

Do not exceed the maximum authorised

speed of 50 mph (80 km/h) or the maximum

distance of 50 miles (80 km).

Driving with more than one spare wheel of

this type is prohibited.

The wheel trim from the replaced wheel must

not be refitted.

Go to a PEUGEOT dealer or a qualified

workshop.

The headlamps have polycarbonate

Have the tightening of the spare wheel's bolts

lenses with a protective coating:

► Tighten the security bolt using the

and its tyre pressure checked.

- Do not clean them with a dry or abrasive

wheelbrace 5 equipped with a security socket 2.

Have the punctured tyre examined. After

cloth, nor with detergent or solvent

► Tighten the other bolts using the

inspection, the technician will advise you on

products.

wheelbrace 5 only.

whether the tyre can be repaired or if it must

- Use a sponge and soapy water or a pH

► Refit the bolt covers to each of the bolts

be replaced.

neutral product.

(depending on equipment).

- When using a high-pressure washer on

► Store the tools.

persistent marks, do not keep the lance

directed towards the headlamps, lamps or

183

CarManuals2.com

In the event of a breakdown

their edges for too long, so as not to damage

- Brake lamps.

Model with LED technology

their protective coating and seals.

- Third brake lamp.

headlamps

- Number plate lamps.

Changing a bulb must only be done with

Replacement of this type of bulb

the ignition off and after the headlamp /

Contact a PEUGEOT dealer or a

lamp has been switched off for several

qualified workshop.

minutes - risk of serious burns!

Do not touch LED or Full LED technology

Do not touch the bulb directly with your

headlamps - risk of electrocution!

fingers; use a lint-free cloth.

It is essential only to use anti-ultraviolet

(UV) type bulbs, so as not to damage the

Front lamps

headlamp.

Always replace a failed bulb with a new bulb

Model with Full

of the same type and specification. To avoid

LED technology headlamps

lighting imbalance, replace the bulbs in pairs.

1. Dipped beam headlamps (LED)

2. Main beam headlamps (LED)

Refitting the lamp units

3. Direction indicators (PY21W amber).

Perform the operations in the reverse

4. Daytime running lamps / Sidelamps (LED)

order to dismantling.

Opening the bonnet/Accessing the

bulbs

Light-emitting diode (LED)

Proceed with caution when the engine is hot -

risk of burns!

headlamps and lamps

Take care with objects or clothing that could

Depending on version, the affected types of

be caught in the blades of the cooling fan -

headlamps/lamps are:

risk of strangulation!

- LED technology headlamps.

- Full LED technology headlamps.

1. Dipped beam headlamps

- Front foglamps.

2. Main beam headlamps

Direction indicators

- Offset daytime running lamps.

3. Direction indicators

- Direction indicator side repeaters.

4. Daytime running lamps / Sidelamps

Rapid flashing of a direction indicator

- Side spotlamps.

lamp (left or right) indicates that one of

– 3D rear lamps.

184

CarManuals2.com

In the event of a breakdown

the bulbs on the corresponding side has

Installing electrical accessories

3. Reversing lamps (LED)

failed.

The vehicle's electrical system is

4. Direction indicators (LED)

designed to operate with standard or optional

equipment.

Foglamp (P21W)

Before fitting other electrical equipment

or accessories to your vehicle, contact a

PEUGEOT dealer or a qualified workshop.

PEUGEOT accepts no responsibility for

the cost incurred in repairing the vehicle

► Remove the protective cover by pulling the

or for rectifying malfunctions resulting from

tab.

the installation of accessories not supplied or

► Turn the bulb holder anti-clockwise.

This bulb is replaced from outside the rear

not recommended by PEUGEOT and not

► Pull the bulb and bulb holder assembly

bumper.

installed in accordance with its

backwards.

► Pass your hand under the bumper.

recommendations, in particular when the

► Replace the bulb.

► Disconnect the connector.

combined power consumption of all of the

► Turn the bulb holder a quarter turn and

additional equipment connected exceeds 10

Amber coloured bulbs must be replaced

remove it.

milliamperes.

by bulbs with identical specifications and

► Turn the bulb a quarter turn and replace it.

colour.

When changing the bulb within a few

12 V battery / Accessory

minutes of switching off the ignition, take

Rear lamps

care not to touch the exhaust - risk of burns!

battery

Lead-acid starter batteries

Fuses

These batteries contain harmful

Changing a fuse

substances (sulphuric acid and lead).

All work must be carried out only by a

They must be disposed of in accordance

PEUGEOT dealer or a qualified workshop.

with regulations and must never under any

The replacement of a fuse by a third party

circumstances be discarded with household

1. Sidelamps / Daytime running lamps (LED)

could cause a serious malfunction of the

waste.

2. Brake lamps (LED)

vehicle.

185

CarManuals2.com

In the event of a breakdown

Dispose of used batteries at a designated

Electronic control units/LED

Symbols

collection point.

technology headlamps

No sparks or naked flames, no smoking.

Never connect the negative jump lead to the

Protect your eyes and face before

metal part of the electronic control units or at

Always protect your eyes. Explosive

handling the battery.

the back of the headlamps.

gases can cause blindness and injury.

All operations on the battery must be carried

Risk of destroying the electronic control units

Keep the vehicle's battery out of the reach

out in a well ventilated area and away from

and/or headlamps!

of children.

naked flames and sources of sparks, to avoid

Connect to the remote earth point provided

The vehicle's battery contains sulphuric

any risk of explosion or fire.

for this purpose.

acid which can make you go blind or

Wash your hands afterwards.

cause severe burns.

Automatic gearbox

For more information, refer to the

Electronic control units/LED

Never try to start the engine by pushing

handbook.

technology headlamps

the vehicle.

Explosive gases can be present close to

Never connect the negative jump lead to the

the battery.

metal part of the electronic control units or at

Electric vehicles

Procedure for starting the engine using another

the back of the headlamps.

battery or for charging a discharged battery.

Flat accessory battery

Risk of destroying the electronic control units

It is no longer possible to start the motor

Accessing the battery

and/or headlamps!

or recharge the traction battery.

Connect to the remote earth point provided

The battery is located under the bonnet.

for this purpose.

Precautions before working on the

accessory battery

Frozen battery

Select mode P, switch off the ignition, check

Never try to charge a frozen battery - risk

that the instrument panel is off and that the

of explosion!

vehicle is not being charged.

If the battery has frozen, have it checked by a

PEUGEOT dealer or by a qualified workshop,

who will verify that the internal components

Jump-starting another vehicle

have not been damaged and that the case

Do not use the accessory battery to

For access to the (+) terminal:

has not cracked, which could lead to a risk of

jump-start another vehicle or to charge

► Release the bonnet by pulling the internal

leakage of toxic and corrosive acid.

another vehicle's battery.

release lever, then the external safety catch.

► Raise the bonnet.

186

CarManuals2.com

In the event of a breakdown

(+) Positive terminal with a quick-release

► Allow the engine to run for at least

terminal.

30 minutes, with the vehicle stationary, so that

(-) Negative terminal.

the battery reaches an adequate state of charge.

The negative terminal is a fastening bracket on

Driving immediately without having

the battery's negative terminal.

reached a sufficient level of charge may

affect some of the vehicle's functions (e.g.

Starting using another

Stop & Start).

battery

► Lift the plastic cover on the (+) terminal, if the

If the vehicle's battery is flat, the engine can be

vehicle has one.

Charging the battery using a

started using a backup battery (either external or

► Connect the red cable to the (+) terminal of

from another vehicle) and jump leads or using a

battery charger

flat battery A (at the metal elbow), then to the

battery booster.

For optimum service life of the battery, it is

(+) terminal of the backup battery B or of the

essential to maintain an adequate state of

Never start the engine by connecting a

booster.

charge.

battery charger.

► Connect one end of the green or black cable

In some circumstances, it may be necessary to

Never use a 24 V or higher battery booster.

to the (-) terminal of the backup battery B or of

charge the battery:

Check beforehand that the backup battery

the booster (or to an earth point on the assisting

- When using the vehicle mainly for short

has a nominal voltage of 12 V and a capacity

vehicle).

journeys.

at least equal to that of the discharged

► Connect the other end of the green or black

- If the vehicle is to be taken off the road for

battery.

cable to the earth point C.

several weeks.

The two vehicles must not be in contact with

► Start the engine on the assisting vehicle and

Consult a PEUGEOT dealer or a qualified

each other.

leave it running for a few minutes.

workshop.

Switch off all electricity-consuming equipment

► Operate the starter on the broken down

on both vehicles (audio system, wipers,

vehicle and let the engine run.

To charge the vehicle's battery yourself,

lighting, etc.).

If the engine does not start immediately, switch

use only a charger compatible with

Make sure that the jump leads are well away

off the ignition and wait a few moments before

lead-acid batteries with a nominal voltage of

from the engine’s moving parts (fan, belt,

trying again.

12 V.

etc.).

► Wait for it to return to idle.

Do not disconnect the (+) terminal while the

► Disconnect the jump leads in reverse order.

Follow the instructions provided by the

engine is running.

► Refit the plastic cover to the (+) terminal, if

manufacturer of the charger.

the vehicle has one.

Never reverse polarities.

187

CarManuals2.com

In the event of a breakdown

It is not necessary to disconnect the

If this label is present, use only a 12 V

Quick-release terminal clamp

battery.

charger to avoid causing irreversible

Disconnecting the (+) terminal

damage to the electrical components.

► Switch the ignition off.

► Switch off all electrical consumers (audio

24V

system, lighting, wipers, etc.).

12V

Disconnecting/reconnecting

the battery

► Depending on equipment, lift the plastic cover

In order to maintain an adequate state of

on the (+) terminal.

► Switch off charger B before connecting

charge for starting the engine, we recommend

► Raise lever A fully to release clamp B.

the cables to the battery, so as to avoid any

disconnecting the battery if the vehicle is to be

► Remove clamp B by lifting it off.

dangerous sparks.

unused for an extended period.

Reconnecting the (+) terminal

► Ensure that the charger cables are in good

Before disconnecting the battery:

condition.

► Close all openings (doors, boot, windows,

► Lift the plastic cover on the (+) terminal, if the

roof).

vehicle has one.

► Switch off all electricity-consuming devices

► Connect the cables of charger B as follows:

(audio system, wipers, lamps, etc.).

• the positive (+) red cable to the (+) terminal

► Switch off the ignition and wait for 4 minutes.

of battery A.

After accessing the battery, it is only necessary

• the negative (-) black cable to earth point C

to disconnect the (+) terminal.

on the vehicle.

► At the end of the charging operation, switch

off charger B before disconnecting the cables

from battery A.

► Raise lever A fully.

► Refit open clamp B on the (+) terminal.

► Push clamp B fully down.

188

CarManuals2.com

In the event of a breakdown

► Lower lever A to lock clamp B.

The Stop & Start system may not be

When the vehicle is towed with its engine

► Depending on equipment, lower the plastic

operational during the trip following the

off, there is no longer braking and steering

cover on the (+) terminal.

first engine start.

assistance.

In this case, the system will only be available

Do not force the lever when pressing on

again after a continuous period with the

A professional recovery service must

it, as if the clamp is not positioned

vehicle immobilised, the duration of which

be called in the following cases:

correctly, locking will then not be possible.

depends on the exterior temperature and the

- broken down on a motorway or main road;

Start the procedure again.

state of charge of the battery (up to about 8

- not possible to put the gearbox into neutral,

hours).

unlock the steering, or release the parking

Following reconnection

brake;

After reconnecting the battery, turn on the

- not possible to tow a vehicle with an

ignition and wait 1 minute before starting the

Towing the vehicle

automatic gearbox, with the engine running;

engine, to enable the electronic systems to

- towing with only two wheels on the ground;

initialise.

General recommendations

- four-wheel drive vehicle;

If minor problems nevertheless persist following

Observe the legislation in force in the

- no approved towbar available.

this operation, contact a PEUGEOT dealer or a

country where you are driving.

qualified workshop.

Check that the towing vehicle is heavier than

Before towing the vehicle, it is essential

Referring to the relevant section, reinitialise

the towed vehicle.

to put the vehicle in free-wheeling mode.

certain equipment:

The driver must remain at the wheel of the

For more information on Free-wheeling, refer

- Remote control key or electronic key

towed vehicle and must have a valid driving

to the corresponding section.

(depending on version).

licence.

- Sunroof.

When towing a vehicle with all four wheels on

Electric motor

- Electric windows.

the ground, always use an approved towbar;

An electric vehicle cannot under any

- Date and time.

ropes and straps are prohibited.

circumstances be used to tow another

- Preset radio stations.

The towing vehicle must move off gently.

vehicle.

However, it may be used, for example, to exit

a rut.

189

CarManuals2.com

In the event of a breakdown

Towing constraints

Type of vehicle

Front wheels on the

Rear wheels on the

Flatbed

4 wheels on the ground

(engine/gearbox)

ground

with towbar

Internal combustion/Manual

Internal combustion/Automatic

Electric 2WD

In case of battery or electric parking brake failure, it is essential to call a professional using flatbed recovery vehicles (excluding manual gearbox).

► Screw the towing eye in fully.

Accessing the tools

► Install the towbar.

For more information on accessing the Tool kit,

► Put the gearbox into neutral.

refer to the corresponding section.

Failure to observe this instruction could

Towing your vehicle

result in damage to certain components

To access the front screw thread:

(e.g. braking, transmission) and to the

absence of braking assistance the next time

the engine is started.

Automatic gearbox

► Unclip the cover by pressing on its left-hand

Never tow the vehicle with the driving

section.

wheels on the ground and the engine off.

► Release the cover to the right and then

► Unlock the steering and release the parking

downwards.

brake.

To be towed:

190

CarManuals2.com

Technical data

must be reduced by 10% for each additional

Engine technical data and

1,000 metres of altitude.

towed loads

The maximum authorised nose weight

corresponds to the weight permitted on the

Engines

towball.

The engine characteristics are given in the

When exterior temperatures are high, the

vehicle's registration document, as well as in

vehicle performance may be limited in

sales brochures.

order to protect the engine. When the exterior

Only the values available at the time of

temperature is higher than 37°C, reduce the

publication are presented in the tables.

towed weight.

Contact a PEUGEOT dealer or a qualified

workshop to obtain missing values.

Towing even with a lightly loaded vehicle

The maximum power corresponds to the

can adversely affect its road holding.

value type-approved on a test bed, under

Braking distances are increased when towing

conditions defined by European legislation

a trailer.

(Directive 1999/99/EC).

When using a vehicle to tow, never exceed

a speed of 62 mph (100 km/h) (observe the

For more information, contact a PEUGEOT

local legislation in force).

dealer or a qualified workshop.

Weights and towed loads

The weights and towed loads relating to

the vehicle are indicated on the registration

document, as well as in sales brochures.

These values are also indicated on the

manufacturer's plate or label.

For more information, contact a PEUGEOT

dealer or a qualified workshop.

The GTW (Gross Train Weight) and towed load

values indicated are valid up to a maximum

altitude of 1,000 metres. The towed load value

192

CarManuals2.com

Technical data

Engines and towed loads - Petrol

Engines

1.2 PureTech 100 S&S

1.2 PureTech 130

1.2 PureTech 130 S&S

Gearboxes

BVM6

EAT6

BVM6

EAT8

(Manual 6-speed)

(Auto. 6-speed)

(Manual 6-speed)

(Auto. 8-speed)

Codes

EB2ADTD MB6 STT

EB2ADTSM AT6III

EB2ADTS MB6 STT

EB2ADTS ATN8 STT

EB2ADTD_I MB6 STT

EB2ADTS_I MB6 STT

EB2ADTS_I ATN8 STT

Model codes:

HNK

HNL

HNS

UR...

Cubic capacity (cc)

1,199

Max. power: EC standard (kW)

Fuel

Unleaded

(RON 95 minimum)

(RON 91 minimum)

(RON 95 minimum)

Braked trailer (within the GTW limit) (kg)

1,200

500

1,200

on a 10% or 12% gradient

Unbraked trailer (kg)

630

500

633

640

Maximum authorised nose weight (kg)

193

CarManuals2.com

Technical data

- European whole vehicle type approval

Dimensions (mm)

number.

These dimensions have been measured on an

- Vehicle Identification number (VIN).

unladen vehicle.

- Gross vehicle weight (GVW).

- Gross train weight (GTW).

- Maximum weight on the front axle.

- Maximum weight on the rear axle.

D. Tyres/paint code label.

Affixed to the driver's door.

Bears the following information about the tyres:

Identification markings

- Tyre pressures, unladen and laden.

- Tyre specification, made up of the dimensions

Various visible markings for vehicle identification

and type as well as the load and speed indices.

and vehicle search.

- Spare tyre inflation pressure.

Also indicates the paint colour code.

The vehicle may be originally equipped

with tyres with higher load and speed

indices than those indicated on the label,

without affecting tyre pressure (on cold tyres).

In the event of a change in the type of tyres,

contact a PEUGEOT dealer for the tyre fits

approved for the vehicle.

A. Vehicle Identification Number (VIN), under

the bonnet.

Stamped on the chassis.

B. Vehicle Identification Number (VIN), on the

dashboard.

Printed on an adhesive label visible through the

windscreen.

C. Manufacturer's label.

Affixed to the right-hand door.

Bears the following information:

- Manufacturer’s name.

196

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

(short-circuit) that could lead to death

With the ignition off, a press turns the system on.

Touch screen 10" &

(electrocution)!

Increase or decrease the volume using

Bluetooth Radio &

In the event of a problem, always contact a

the wheel or the "plus" or "minus" buttons

PEUGEOT dealer or a qualified workshop.

(depending on the equipment).

Telephone

Use the buttons on either side of or below the

The system is protected so that it only

touch screen to access the menus, then press

Multimedia audio system -

operates in the vehicle.

the virtual buttons on the touch screen.

Applications - Bluetooth^®

The message Energy economy mode is

Depending on the model, use the "HOME" and

displayed when the system is about to go into

"Vehicle" buttons below the touch screen to

telephone

standby.

access the menus, then press the virtual buttons

The functions and settings described

on the touch screen.

vary according to the vehicle version and

At all times it is possible to display the rolling

The system’s Open Source Software

configuration, as well as the country of sale.

menus by pressing the screen briefly with three

(OSS) source codes are available at the

fingers.

following addresses:

On pages with multiple tabs at the bottom of the

For safety reasons and because they

https://www.groupe-psa.com/fr/oss/

screen, you can switch between pages either

require sustained attention by the driver,

https://www.groupe-psa.com/en/oss/

by tapping the tab for the desired page or by

the following operations must be carried out

swiping the pages to the left or right with your

with the vehicle stationary and the ignition

The system transmits and/or receives

finger.

on:

radio waves subject to the Directive

Press the back arrow to go back a level or

- Connecting the smartphone via Bluetooth,

2014/53/EU.

confirm.

USB or Wi-Fi.

The manufacturers of the mentioned system

- Using the smartphone.

declare the conformity with the Directive

The touch screen is of the "capacitive"

- Connecting to the CarPlay^® or Android

2014/53/EU.

type.

Auto applications (certain applications stop

The full text of the EU declaration of

To clean the screen, use a soft, non-abrasive

displaying when the vehicle is moving).

conformity for each system is available at the

cloth (e.g. spectacles cloth) with no additional

- Changing the system settings and

following address:

product.

configuration.

http://public.servicebox.peugeot.com/APddb/

Do not use sharp objects on the screen.

Do not touch the screen with wet hands.

Any intervention or modification on the

Certain information is displayed permanently on

vehicle's system is strictly forbidden

First steps

the main screen:

- Risk of serious burns or electric shock

With the engine running, a press mutes

the sound.

197

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

- Air conditioning status information (depending

Menus

Vol-^{Decrease volume.}

on version), and direct access to the

Mute by pressing the volume increase

corresponding menu.

and decrease buttons simultaneously

Radio Media

- Radio Media and Telephone menu status

(depending on equipment).

information.

Restore the sound by pressing one of the two

- Privacy status information.

volume buttons.

- Access to the touch screen and digital

Telephone (short press): start telephone

instrument panel settings.

call.

Audio source selection (depending on

Call in progress (short press): access

equipment):

telephone menu.

- FM/DAB/AM radio stations (depending on

Telephone (long press): reject an incoming call,

equipment).

end call; when no call is in progress, access

- Telephone connected via Bluetooth and

telephone menu.

Bluetooth multimedia broadcast (streaming).

Radio (rotate): automatic search for the

- USB Memory stick.

previous/next station.

Select an audio source or radio station.

Media (rotate): previous/next track, move

In very hot conditions, the volume may

through a list.

be limited to protect the system. It may

Short press: confirm a selection; if nothing

enter standby mode (with the screen and

Telephone

selected, access presets.

sound off) for 5 minutes or more.

Accelerated navigation.

The system will resume normal operation

when the temperature in the passenger

compartment has dropped.

The system is operational in temperatures

between -40°C and +70°C.

Steering mounted controls

Voice control: smartphone voice

commands.

Connect a mobile phone via Bluetooth^®.

Run certain applications from a

Vol+^{Increase volume.}

smartphone connected via CarPlay^® or Android

Auto.

198

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

Applications

Driving

Air conditioning

Access configurable equipment.

Activate, deactivate or configure certain

Manage various temperature and air flow

vehicle functions.

settings.

Settings

Navigation

Radio

Selecting a station

Press Radio Media to display the main

page.

Press one of the buttons to perform an

automatic search for radio stations.

Move the slider to manually search for

frequencies up or down.

Configure the navigation and select your

Configure the sound (balance, ambience,

Press the frequency to enter the FM and

destination via CarPlay^® or Android Auto.

etc.), the display (language, units, date,

AM waveband values using the virtual

time, etc.), and some system functions.

keypad.

Press "OK" to confirm.

199

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

Radio reception may be affected by the

Activating/Deactivating RDS

Playing TA messages

use of electrical equipment not approved

RDS, if activated, allows you to continue

The TA (Traffic Announcement) function gives

by the Brand, such as a USB charger

listening to the same station by automatically

priority to TA alert messages. To operate, this

connected to the 12 V socket.

retuning to alternative frequencies.

function needs good reception of a radio station

The exterior environment (hills, buildings,

Press Radio Media to display the main

that transmits this type of message. While traffic

tunnels, basement car parks, etc.) may

page.

information is being broadcast, the current

block reception, including in RDS mode.

Press the "OPTIONS" button to access the

media is automatically interrupted so that the

This phenomenon is perfectly normal in the

secondary page.

TA message can be heard. Normal play of the

context of radio wave transmission, and

Activate/deactivate "RDS".

previously playing media resumes at the end of

in no way indicative of an audio system

the message.

malfunction.

Press in the shaded area to confirm.

Press Radio Media to display the main

page.

Changing the waveband

Press the "OPTIONS" button to access the

RDS station tracking may not be

secondary page.

Press Radio Media to display the main

available nationwide, as many radio

Activate/deactivate "TA".

page.

stations do not cover 100 % of the country.

Press the "OPTIONS" button to access the

This explains the loss of reception of the

Press in the shaded area to confirm.

secondary page.

station during a journey.

Press "Band" to change waveband.

Displaying text information

Audio settings

Press in the shaded area to confirm.

The "Radio Text" function displays information

Press Radio Media to display the main

transmitted by the radio station relating to the

page.

Presetting a station

station or the currently playing song.

Press the "OPTIONS" button to access the

Press Radio Media to display the main

secondary page.

Select a radio station or frequency.

page.

Press "Audio settings".

Make a short press on the star outline. If

the star is solid, the radio station is

Press the "OPTIONS" button to access the

secondary page.

Select the "Tone", "Balance" or "Sound"

already preset.

Activate/deactivate "News".

tab to configure the sound settings.

Press the back arrow to confirm.

Select a radio station or frequency.

Press "Preset".

Press in the shaded area to confirm.

Make a long press on one of the buttons

In the "Tone" tab, the Ambience, Bass,

to preset the station.

Medium and Treble sound settings are

200

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

different and independent for each audio

Press the "OPTIONS" button to access the

If the "DAB" station being listened to is

source.

secondary page.

not available on "FM", or if "FM-DAB

In the "Balance” tab, the All passengers,

Press "Band" to select "DAB band".

Follow-up" is not activated, the sound will cut

Driver and Front only settings are common

out when the digital signal becomes too weak.

to all sources.

Press in the shaded area to confirm.

In the "Sound” tab, activate or deactivate

"Volume linked to speed", "Auxiliary input"

Media

and "Touch tones".

FM-DAB Follow-up

"DAB" does not cover 100% of the territory.

USB port

The balance/distribution (or spatialisation

When the digital radio signal is poor, the

Insert the USB memory stick into the USB

with the Arkamys^© system) uses audio

"FM-DAB Follow-up" enables you to continue

port or connect the USB device to the

processing to adjust the sound quality

listening to the same station by automatically

USB port using a suitable cable (not supplied).

according to the number of passengers in the

switching to the corresponding "FM" analogue

vehicle.

station (if there is one).

To protect the system, do not use a USB

Press Radio Media to display the main

hub.

page.

Onboard audio: Arkamys Sound Staging^©

Press the "OPTIONS" button to go to the

The system builds playlists (in temporary

optimises the sound distribution inside

secondary page.

memory); this operation can take from a

the passenger compartment.

Activate/deactivate "FM-DAB Follow-up".

few seconds to several minutes at the first

connection.

Press in the shaded area to confirm.

Reduce the number of non-music files and the

DAB (Digital Audio

number of folders to reduce the waiting time.

Broadcasting) radio

Playlists are updated whenever the ignition

If "FM-DAB Follow-up" is activated, there

is switched off or a USB memory stick is

may be a time offset of a few seconds

connected. The audio system memorises these

Terrestrial Digital Radio

when the system switches to "FM" analogue

lists, which will subsequently load faster if they

Digital radio provides higher quality sound.

radio, and in some cases a change in volume.

have not been changed.

The various "multiplexes/ensembles" offer a

When the digital signal quality is restored, the

choice of radio stations organised in alphabetical

system automatically changes back to "DAB".

Selecting the source

order.

To minimise this time lag, storing radio

Press Radio Media to display the main

stations in the "DAB" band is recommended.

page.

Press the "SOURCES" button.

Select the source.

201

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

BluetoothStreaming^®

confirm to go down through the menu to the

Use only USB memory sticks in FAT32 format

desired track.

(File Allocation Table).

Streaming allows you to listen to the audio feed

from your smartphone.

We recommend using the original USB

The version of software in the audio system may

The Bluetooth profile must be activated.

cable for the portable device.

not be compatible with the generation of the

First adjust the volume on the portable device

Apple^® player.

(to a high level). Then adjust the volume of the

system.

Information and advice

Telephone

If play does not start automatically, it may be

The system supports USB mass storage

necessary to start the audio playback from the

devices, BlackBerry^® devices or Apple^® players

Pairing a Bluetooth^®

smartphone.

via the USB ports. The adapter cable is not

Control is from the portable device or by using

telephone

supplied.

the system's touch buttons.

Devices are managed using the audio system

The services available depend on the

Once connected in Streaming mode, the

controls.

network, the SIM card and the

smartphone is considered to be a media

Other devices, not recognised on connection,

compatibility of the Bluetooth devices used.

source.

must be connected via Bluetooth streaming, if

Consult the telephone user guide and the

compatible.

service provider to check which services are

To protect the system, do not use a USB

available.

Connecting Apple^® players

hub.

Connect the Apple^® player to the USB socket

The Bluetooth function must be activated and

using a suitable cable (not supplied).

the telephone configured as "Visible to all” (in the

The audio system will only play audio files with

Play starts automatically.

telephone settings).

".wav", ".wma", ".aac", ".ogg" and ".mp3" file

Control is via the audio system.

To complete the pairing, whichever procedure is

extensions, at bit rates between 32 Kbps and

320 Kbps.

used (from the telephone or from the system),

The classifications available are those of

It also supports VBR (Variable Bit Rate) mode.

ensure that the code is the same in the system

the portable device connected (artists/

No other file types (".mp4", etc.) can be read.

and in the telephone.

albums/genres/playlists/audio books/

podcasts). It is also possible to use a

All ".wma" files must be standard WMA 9 files.

If the pairing procedure fails, we

classification structured in the form of a

The supported sampling rates are 11, 22, 44 and

recommend deactivating and then

library.

48 KHz.

reactivating the Bluetooth function on the

The default classification used is by artist. To

To avoid reading and display problems, we

telephone.

modify the classification used, return to the

recommend choosing file names less than 20

first level of the menu then select the desired

characters long that do not contain any special

classification (playlists for example) and

characters (e.g. “ ? . ; ù).

202

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

Procedure from the telephone

The ability of the system to connect just

Managing paired telephones

Select the name of the system in the list

one profile depends on the telephone.

This function lets you connect or disconnect a

of detected devices.

All three profiles may connect by default.

device or delete a pairing.

In the system, accept the connection request

Press Telephone to display the main

from the telephone.

The profiles compatible with the system

page.

are: HFP, OPP, PBAP, A2DP, AVRCP,

Press the "PHONE" button to access the

Procedure from the system

MAP and PAN.

secondary page.

Press Telephone to display the main

Press "Bluetooth connection" to

Visit the Brand's website for more information

page.

display the list of paired devices.

(compatibility, additional help, etc.).

Press "Connected Devices".

Press on the name of the telephone

The list of detected telephones is

selected in the list to disconnect it.

Automatic reconnection

displayed.

Press again to connect it.

On returning to the vehicle, if the last telephone

Press this button to start searching for

connected is present again, it is automatically

Deleting a telephone

new devices.

recognised and within about 30 seconds

Select the name of the chosen telephone

Press the basket at the top right of the

after switching on the ignition, the pairing is

in the list.

screen to display a basket alongside the

established automatically (Bluetooth activated).

Complete the pairing with the displayed code.

telephone chosen.

To modify the connection profile:

Press the basket alongside the telephone

Connection sharing

Press Telephone to display the main

chosen to delete it.

page.

The system offers to connect the telephone with

3 profiles:

Press the "PHONE" button to access the

Receiving a call

secondary page.

- "Telephone" (hands-free kit, telephone only),

An incoming call is announced by a ring and a

Press "Bluetooth connection" to

- “Streaming" (streaming: wireless playing of

superimposed display in the screen.

display the list of paired devices.

audio files on the telephone),

Make a short press on the steering

Press the "Details" button for a paired

- "Mobile internet data".

mounted PHONE button to accept an

device.

Select one or more profiles.

incoming call.

Select one or more profiles.

And

Press "OK" to confirm.

Make a long press

Press "OK" to confirm.

Depending on the type of telephone, you may by

on the steering mounted PHONE button

prompted to accept the transfer of contacts and

to reject the call.

messages.

203

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

Press "End call".

Calling a recently used

technology on the vehicle’s screen. For CarPlay^®

technology, the CarPlay^® function must first be

number

activated on the smartphone.

Making a call

Press Telephone to display the main

The smartphone can be connected via USB

page.

cable or via a wireless connection.

Using the telephone is not recommended

while driving.

Unlock the smartphone for the

Press and hold

Parking the vehicle.

communication process between the

Make the call using the steering mounted

smartphone and the system to work.

the steering mounted button.

controls.

As principles and standards are constantly

changing, we recommend keeping the

Press "Recent calls".

smartphone's operating system up-to-

Select the desired contact from the displayed list.

Calling a new number

date, together with the date and time on

Press Telephone to display the main

It is always possible to make a call

the smartphone and the system.

page.

directly from the telephone; as a safety

Enter the phone number using the digital

measure, first park the vehicle.

For the list of compatible smartphones,

keypad.

visit the Manufacturer's website in your

Press "Call" to start the call.

Setting the ringtone

country.

Press Telephone to display the main

USB sockets

Calling a contact

page.

Press the "OPTIONS" button to access the

Depending on equipment, for more information

Press Telephone to display the main

secondary page.

on the USB sockets compatible with CarPlay^® or

page.

Press "Ring volume" to display the

Android Auto applications, refer to the "Ease of

Or press and hold

volume bar.

use and comfort" section.

Press the arrows or move the slider to set

Wireless connection

the steering mounted PHONE button.

the ring volume.

Before using CarPlay^® or Android Auto

Press "Contacts".

Using CarPlay^® or Android

wirelessly, ensure the Wi-Fi regulatory

Select the desired contact from the displayed list.

restrictions of your geographic location are

Press "Call".

Auto

Synchronising a smartphone enables users

to display applications that support the

smartphone’s CarPlay^® or Android Auto

204

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

met, as indicated by a message on the touch

CarPlay^® smartphone

The CarPlay^® navigation can be accessed

screen.

at any time by pressing the system's

connection

If the 5 GHz Wi-Fi network frequency is not

Navigation button.

allowed in your location, select 2.4 GHz at the

The availability of the application depends on the

Wireless connection

first connection.

country.

First activate the smartphone’s Bluetooth^®

Check the Wi-Fi restrictions again when you

USB connection

function.

travel to different locations and set the Wi-Fi

From the system, press "Telephone" to

frequency accordingly.

On connecting the USB cable, the

display the main page.

The regulations of the 5 GHz frequency

CarPlay^® function deactivates the

If the device has already been connected to the

are specific to each country. Refer to the

system's Bluetooth^® mode.

system via Bluetooth^®, select the device settings

regulation in force in your country.

The "CarPlay" function requires the use of

from the list of known devices and choose

a compatible smartphone and compatible

CarPlay^® as the wireless connection mode.

applications.

When using CarPlay^® with 5 GHz

If the device has never been connected to the

frequency activated, there may be

Connect the USB cable.

system before, it will have to be paired (refer to

interference with certain devices (tolls,

the corresponding section).

parking...) resulting in a disconnection. To

The smartphone charges when connected by the

The system detects if the smartphone is

prevent this from happening, it is

USB cable.

compatible with CarPlay^® and offers to connect

recommended to disable the 5 GHz function.

From the system, press "Telephone" to

to it following the pairing process.

display the main page.

Subsequent automatic connection of the

Difficulties in connecting wirelessly your

Press "CarPlay" to display the CarPlay^®

smartphone requires activation of the Bluetooth^®

smartphone may happen, due to:

interface.

on your device.

- Interference with other Wi-Fi networks.

As soon as the connection is established,

CarPlay^® interface may appear

- Interference with certain devices (tolls,

press "CarPlay" to display the CarPlay^®

automatically.

parking) when using Android Auto.

interface.

- An unsuitable configuration of the

Press and hold this steering-mounted

smartphone.

When the USB cable is disconnected

control button and say "Siri" to initiate the

In these cases, it is recommended to connect

and the ignition is switched off then back

smartphone voice commands.

the smartphone with its original cable.

on, the system will not automatically switch to

Radio Media mode; the source must be

Android Auto smartphone

changed manually.

connection

The availability of the application depends on the

country.

205

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

On the smartphone, download the

Wireless connection

There may be a pause before

Android Auto application.

First activate the smartphone’s Bluetooth^®

applications become available,

function.

depending on the quality of the network.

The "Android Auto" function requires the

Connect a USB cable.

use of a compatible smartphone and

applications.

From the system, press "Telephone" to

Applications

display the main page.

The first connection of Android Auto to

If the device has already been connected to the

the system should be made by USB

Viewing photos

system via Bluetooth^®, select the device settings

cable.

Insert a USB memory stick in the USB port.

from the list of known devices and choose

Android Auto^® as the wireless connection mode.

To protect the system, do not use a USB

USB connection

If the device has never been connected to the

hub.

Connect a USB cable.

system before, it will have to be paired (refer to

The system can read folders and image files in

the corresponding section).

the formats: .tiff; .gif; .jpg/jpeg; .bmp and .png.

The system detects if the smartphone is

The smartphone charges when connected by a

Press Applications to display the main

USB cable.

compatible with Android Auto and offers to

page.

From the system, press "Telephone" to

connect to it following the pairing process.

Press "Photos".

display the main page.

Subsequent automatic connection of the

Press "Android Auto" to start the

smartphone requires activation of the Bluetooth^®

Select a folder.

application in the system.

on your device.

Depending on the smartphone, it may be

As soon as the connection is established,

Select an image to view.

necessary to activate the "Android Auto"

press "Android Auto" to display the

function.

Android Auto interface.

Press this button to display the details of

During the procedure, several screen

Press and hold this steering-mounted

the photo.

pages relating to certain features are

control button and say "OK Google" to

Press the back arrow to go back a level.

displayed.

initiate the smartphone voice commands.

Accept to start and complete the connection.

Access to the different audio sources remains

When connecting a smartphone to the

available in the margin of the Android Auto

Managing messages

system, we recommend enabling

display, using the touch buttons located in the

upper bar.

Press Applications to display the main

Bluetooth^® on the smartphone.

Access to the menus for the system is possible

page.

at any time using the dedicated buttons.

Press "SMS".

206

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

Select the "SMS” tab.

Move the slider to adjust the brightness of

- "Only data sharing”

the screen and/or the instrument panel

- "Data and vehicle position sharing"

Press this button to select the display

(depending on version).

Press the back arrow to confirm.

settings for messages.

Press in the shaded area to confirm.

Press this button to search and select a

Press Settings to display the main page.

recipient.

Select the "Quick messages” tab.

Modifying system settings

Press "Configuration" to access the

Press Settings to display the main page.

secondary page.

Press this button to select the display

Press "Screen configuration".

settings for messages.

Press "Configuration" to access the

Press this button to write a new message.

secondary page.

Press "Brightness".

Press "System configuration".

Move the slider to adjust the brightness of

Press the bin alongside the selected

the screen and/or the instrument panel

message to delete it.

Press the "Units" tab to change the units of

(depending on version).

Press this button alongside the selected

distance, fuel consumption and temperature.

Press the back arrow to confirm.

message to display the secondary page.

Press the "Factory settings" tab to restore the

Press this button to edit and modify the

initial settings.

Press "Animation".

existing text.

Activate or deactivate: “Automatic

Returning the system to factory settings

Press this button to write a new message.

scrolling”.

activates the English language by default

Select "Animated transitions".

(depending on version).

Press the bin to delete the message.

Press the back arrow to confirm.

Press the "System info" tab to display the

versions of the various modules installed in the

Settings

system.

Selecting the language

Press the "Privacy" tab,

Press Settings to display the main page.

Adjusting the brightness

Press Settings to display the main page.

Press "Configuration" to access the

Press "Privacy" to activate or deactivate

secondary page.

Press Brightness.

Select "Language" to change the

the private data mode.

Activate or deactivate:

language.

Press the back arrow to confirm.

- "No sharing (data, vehicle position)".

207

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

Setting the time

Press "Date and time".

Difficulties in connecting wirelessly your

smartphone may happen, due to:

Press Settings to display the main page.

Select "Date".

- Interference with other Wi-Fi networks.

Press this button to set the date.

- Interference with certain devices (tolls,

Press "Configuration" to access the

parking) when using Android Auto.

secondary page.

Press the back arrow to save the date.

- An unsuitable configuration of the

Press "Date and time".

smartphone.

Select the display format for the date.

In these cases, it is recommended to connect

Select "Time".

the smartphone with its original cable.

Press this button to set the time using the

Press the back arrow again to confirm.

virtual keypad.

Press "OK" to save the time.

The regulations of the 5 GHz frequency

are specific to each country.

Time and date setting is only available if

Press this button to set the time zone.

"GPS Synchronisation:" is deactivated.

Refer to the regulation in force in your

country.

Select the display format for the time

Wifi settings

(12h/24h).

Activate or deactivate summer time (+1

Press Settings to display the main page.

Frequently asked

hour).

questions

Press the back arrow to save the settings.

Press "Wifi" to access network frequency

setting.

The following information groups together the

Activate or deactivate the 5 GHz Wifi

answers to the most frequently asked questions

The system may not automatically

function.

concerning the system.

manage the change between winter and

summer time (depending on the country of

Android Auto uses the 5 GHz frequency.

Radio

sale).

CarPlay^® uses the 2,4 and 5 GHz

The reception quality of the tuned radio

frequency.

station gradually deteriorates or the station

Setting the date

presets are not working (no sound, 87.5 MHz

When using CarPlay^® with 5 GHz

is displayed, etc.).

Press Settings to display the main page.

frequency activated, there may be

The vehicle is too far from the selected station’s

interference with certain devices (tolls,

transmitter, or no transmitter is present in the

Press "Configuration" to access the

parking...) resulting in a disconnection. To

geographical area.

secondary page.

prevent this from happening, it is

recommended to disable the 5 GHz function.

208

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

► Activate the "RDS" function in the upper bar

stick (multiplication by 10 of the cataloguing

Android Auto and/or CarPlay do not work.

to enable the system to check whether there is

time).

Android Auto and CarPlay may not activate if the

a more powerful transmitter in the geographical

► Delete the files supplied with the memory

USB cables are of poor quality.

area.

stick and limit the number of sub-folders in the

► Use genuine USB cables to ensure

The environment (hills, buildings, tunnels,

file structure on the memory stick.

compatibility.

basement car parks, etc.) is blocking reception,

Some characters in information about the

Android Auto and/or CarPlay do not work.

including in RDS mode.

currently playing media are not displayed

Android Auto and CarPlay are not available in all

This is a perfectly normal phenomenon, and is

correctly.

countries.

not indicative of an audio system malfunction.

The audio system is unable to process certain

► Check the Google Android Auto or Apple

The aerial is missing or has been damaged

types of character.

website to see which countries are supported.

(for example while entering a car wash or

► Use standard characters to name tracks and

The volume of the telephone connected in

underground car park).

folders.

Bluetooth mode is inaudible.

► Have the aerial checked by a dealer.

Playback of streaming files does not start.

The volume depends on both the system and the

I cannot find some radio stations in the list of

The connected device does not automatically

telephone.

received stations.

launch playback.

► Increase the volume of the audio system, to

The name of the radio station changes.

► Start playback from the device.

maximum if required, and increase the volume of

The station is no longer received or its name has

Track names and playing times are not

the telephone if necessary.

changed in the list.

displayed on the audio streaming screen.

Ambient noise affects the quality of the

► Press the round arrow on the "List" tab on the

The Bluetooth profile does not allow the transfer

telephone call.

"Radio" page.

of this information.

► Reduce ambient noise (close windows, turn

Some radio stations send other information

down ventilation, slow down, etc.).

in place of their name (the title of the song for

Telephone

The contacts are not listed in alphabetical

example).

I cannot connect my Bluetooth telephone.

order.

The system interprets these details as the station

The telephone's Bluetooth function may be

Some telephones offer display options.

name.

switched off or the device may not be visible.

Depending on the settings chosen, contacts can

► Press the round arrow on the "List" tab on the

► Check that the telephone has Bluetooth

be transferred in a specific order.

"Radio" page.

switched on.

► Modify the telephone directory display

► Check in the telephone settings that it is

settings.

Media

"visible to all".

Playback of my USB memory stick starts only

The Bluetooth telephone is not compatible with

Settings

after a very long wait (around 2 to 3 minutes).

the system.

When the treble and bass settings are

Some files supplied with the memory stick may

► Check the compatibility of the telephone on

changed, the ambience is deselected.

greatly slow down access to reading the memory

the Brand's website (services).

209

CarManuals2.com

Touch screen 10" & Bluetooth Radio & Telephone

When the ambience is changed, the treble

► Start the vehicle’s engine to increase the

and bass settings are reset.

charge of the battery.

Selecting an ambience imposes the treble and

bass settings, and vice versa.

► Modify the treble and bass or ambience

settings to obtain the desired musical ambience.

When the balance settings are changed, the

distribution is deselected.

When the distribution setting is changed, the

balance settings are deselected.

Selecting a distribution setting imposes the

balance settings, and vice versa.

► Modify the balance setting or the distribution

setting to obtain the desired sound quality.

There is a difference in sound quality

between audio sources.

To allow for optimal listening quality, the sound

settings can be tailored to different audio

sources, which can generate audible differences

when changing source.

► Check that the sound settings are appropriate

to the sources listened to. Adjust the sound

functions to the middle position.

When the engine is off, the system switches

off after several minutes of use.

When the engine is switched off, the system's

operating time depends on the state of charge of

the battery.

The switch-off is normal: the system

automatically goes into energy economy mode

and switches off to maintain an adequate charge

in the battery.

210

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

The message Energy economy mode is

- Audio equipment and telephone controls with

PEUGEOT i-Connect

displayed when the system is about to go

display of associated information.

Advanced - PEUGEOT

into standby.

- Connected services and display of associated

For more information on Energy economy

information.

i-Connect

mode, refer to the "Practical information"

- Navigation system controls and display

section.

of associated information (depending on

GPS navigation -

equipment).

Applications - Multimedia

The AM radio selection mode is not

- Voice recognition (depending on equipment).

available on electric vehicles.

- Time and outside temperature.

audio system - Bluetooth^®

- Heating/air conditioning system controls and

telephone

reminders of settings.

Warning

- Settings for driving aid functions, comfort

The functions and settings described

Navigation is a driving aid. It cannot

and safety functions, extended head-up display

vary according to the version and

replace the driver. All guidance instructions

(depending on equipment and version), audio

configuration of the vehicle, and according to

should be carefully checked by the user.

equipment and digital instrument panel.

the country of sale.

By using the navigation, you accept the

- Settings for functions specific to electric

following terms and conditions:

vehicles.

https://www.tomtom.com/en_gb/legal/

For safety reasons and because they

- Display of visual manoeuvring aid functions.

eula-automotive/?388448

require continued attention on the part of

- Interactive handbook.

the driver, the following operations must be

- Video tutorials (e.g. screen management,

carried out with the vehicle stationary and

driving aids, voice recognition).

the ignition on:

First steps

Upper banner

- Pairing the smartphone with the system via

The system starts when the ignition is

Bluetooth^®.

Certain information is displayed permanently in

switched on.

- Using the smartphone.

the upper banner of the touch screen:

Short press, ignition off: system on/off.

- Connecting to Mirror Screen

- Outside temperature from the vehicle's

Short press, ignition on: mute/restore sound.

(Apple^®CarPlay^® or Android Auto).

sensors (associated with a blue symbol if there is

Long press, ignition on: start standby mode

- Changing the system settings and

a risk of ice).

(mute sound, screens and clock display off).

configuration.

- Temperature setting reminder for the air

Rotation: volume adjustment.

conditioning on the driver's and passenger sides.

Information

- Charge level of the connected smartphone.

This system gives access to the following

- System connection status (Bluetooth^®, Wi-Fi,

elements:

mobile telephone network).

211

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

- Time.

Access to additional information about the

- Screen configuration, appearance, i-Toggles

- Quick access to the Mirror Screen^® functions

function.

(depending on equipment).

(associated with a connected smartphone).

Access to a function’s settings.

- Audio settings, favourite radio stations.

Swipe down from the upper edge of the touch

- Lighting, interior ambience (refer to the "Ease

screen to access the notifications centre and

Add/delete shortcuts.

of use and comfort" section).

display a list of quick settings :Guest, Privacy

- Navigation history, favourite points of interest

Settings, Brightness, My Devices, night mode,

(POIs), navigation settings.

etc.

Configuring profiles

- Some driving aids and the list of favourites.

Press the "Settings" application.

To delete a profile, select it from the list of

Principles

profiles then press the bin.

► Use this button (HOME) to display the

In the list, select the "Profile" tab.

most recent home page used; a second

The screen displays a "Guest" profile built

Privacy Settings

press displays the first home page, then press

into the system and allows you to create and

The "Privacy Settings" management is

the virtual buttons displayed on the touch screen.

personalise several new profiles with or without

associated with each profile. This function is

Scroll through the home pages by sliding

an associated mobile device.

used with:

your finger along the screen to the right or

The "Guest" profile has a default display

a "Guest" profile configured by default in "Private

to the left.

with the possibility of adding to it and/or

Mode",

returning it to its initial configuration. This profile

Principle of movement in the system

is built into the system and cannot be deleted.

a profile to be created in the system, with or

Depending on the pages displayed on the

Each profile created can be associated

without connection to a mobile device.

screen, scroll through the text or the menu (on

with a mobile device of your choice

For each profile (even "Guest"), the last privacy

the left side of the screen) by sliding your finger,

connected via Bluetooth^®; the Bluetooth^® function

mode saved value will be restored.

as with a smartphone.

of the mobile device must first be activated. This

"Sharing Data and Location"

Touch buttons

association allows the system to detect your

This mode allows the vehicle to externally

Display/hide the context menu.

presence in the vehicle when it starts and to

transmit all the personal data needed for each

propose the activation of your personalised

valid available connected service.

Return to the previous page.

profile.

The personal data required to use the

If a profile is not connected to the mobile device,

connected services is sent to the

► To change the status of a function, press the

the last profile used will be highlighted.

providers of these services.

description for the corresponding line (change

Select "Create Profile", then follow the

confirmed by the slider moving to the right/left:

procedure.

"Sharing Data"

function activated/deactivated).

Creating a new profile allows you to personalise:

This mode allows the vehicle to externally

– Language, units, Privacy Settings.

transmit all the data needed for each valid

212

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

available connected service, with the exception

To change mode, swipe down from the upper

an access key to saved personal information.

of vehicle location data (e.g. GPS coordinates).

edge of the touch screen to display all of the

First activate the mobile device’s Bluetooth^®

quick settings.

function.

Some connected services may not

Press this button and select the chosen

Select the desired application, authentication will

function without the vehicle location data.

mode. The mode is highlighted.

be requested if necessary. This authentication

will be saved for future uses via the mobile

This mode will not be applied to the

Press the "Settings" application.

device connected to the current profile.

emergency call function or to specific

An authentication will be requested at each use if

services to which the user has consented

In the list, select the "Connectivity" tab.

the mobile device is not connected to the current

under the terms of commercial contracts

Select "Privacy Settings".

profile or if the Guest profile is used.

(e.g. Connected alarm).

With the use of the “Guest” profile, an

Choose the mode.

identification will be requested for each

"Private Mode"

use.

This mode does not allow the vehicle to

transmit personal data outside the vehicle.

Internet portal

Updating the system

Connected services will only perform

During the first use, upon acquisition of the

Managing devices remotely and

local processing inside the vehicle with

vehicle, the user is invited to select the country

remote updating of software and

limited functions.

of residence for the use of the Internet portal.

firmware.

If the country is not selected, the notification is

Being an integral part of the service used to

This mode will not be applied to the

stored in the notification centre and disappears

provide connected services contract(s), the

emergency call function or to specific

once the country is selected. Slide a finger on

required management of devices as well as

services to which the user has consented

the touch screen from top to bottom to display all

the required updating of the software and

under the terms of commercial contracts

the notifications.

firmware associated with the aforementioned

(e.g. Connected alarm).

The selection of a country is necessary to use

connected service will be carried out remotely,

the available internet applications.

in particular using "Over the Air" technology.

Professional purposes

Press the "Settings" application.

To do this, a secure connection via radio

If the vehicle is used for professional

network is established between the vehicle

purposes or under the terms of specific

In the list, select the "Connected Services".

and the Manufacturer's device management

contracts (e.g. corporate fleet, government

Choose the country.

server each time the ignition is switched on,

assignment), some privacy modes will not

when a mobile telephone network is available.

be available for the user on the screen,

The first time you use it, via a connected

Depending on the vehicle's equipment,

depending on the data sharing needs of the

mobile device, the system links to your

the connection configuration must be set

services.

profile. The connected mobile device serves as

213

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

to "Connected vehicle" to enable to the

minutes. A notification will give an estimate of the

Personalisation

connection to the radio network.

duration and a description of the update.

Press and hold the screen from one of the

Irrespective of a valid subscription to a

Update information is available through the

system's home pages.

connected service, the remote management

"Settings" application.

of devices relating to or connected with

Press the "Settings" application.

the security of devices, and the updating

of software and firmware, will be carried

In the list, select the "Updates" tab.

out when necessary in order to comply

This button allows you to change the

In the list, select the "Customization" tab.

Press the "Displays" field.

with a legal requirement applicable to the

authorisation for automatic downloading

A page divided into 2 parts is displayed.

Manufacturer (e.g. the applicable law in terms

of updates via an exterior Wi-Fi network.

Press the HOME button at any time to leave this

of product liability, the regulations governing

For safety reasons and because it

page.

e-call) or when necessary to protect the

requires sustained attention on the part

respective vital interests of the vehicle's users

of the driver, the installation must be carried

Personalising the screen

and passengers.

out with the ignition on but without starting the

The establishment of a secure connection via

Press the pencil in the "Customize

engine.

radio network and the corresponding remote

Touchscreen" part.

The installation cannot be carried out in the

updates are not affected by the privacy

A representation of the organisation of the

following cases:

settings and are intended to be carried out

different home page (HOME) Widgets is

- engine running.

after being initialised by the user in response

displayed.

- emergency call in progress.

to a related notification.

- insufficient battery level.

A Widget is a reduced window of an

- when charging for electric vehicles.

application or service.

The system can notify the receipt of an update

when it is connected to an exterior Wi-Fi network

If an update has failed or has expired, contact a

or a mobile telephone network.

Adding a Widget

dealer or a qualified workshop.

Large updates are downloaded only via the Wi-Fi

To add a Widget, press "Widget" on the

network.

The Manufacturer does not charge for

left of the screen.

The availability of an update is notified on the

the use of this service.

screen at the end of the journey with an option

However, the use of Wi-Fi and/or mobile

Press one of these buttons on the screen.

of immediate installation or postponement of

telephone networks by your smartphone may

installation.

incur extra charges if you exceed the data

Select the desired Widget.

The installation time is variable and can take

allowance included in your contract.

Press the back arrow to return to the

several minutes with a maximum of about 30

Any associated costs will be billed to you by

previous page.

your mobile telephone operator.

214

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

Organising the Widgets on a home

Select the desired Widget.

Mirror Screen^® connected (short press): access

page (HOME)

Press the back arrow to return to the

the projected view of the telephone application of

previous page.

your Mirror Screen^® equipment.

To move a Widget, press and hold it, then drag it

Radio: automatic search for the previous/

to the desired location.

Deleting a Widget

next station (in the list of radio stations

Adding a page

To move a Widget to the bin, press and

sorted by name or by frequencies).

hold it, then drag it to the bin.

Media: previous/next track, movement in the

To add a page, press "Page" on the left of

lists.

the screen.

Short press: validate a selection. Out of

Press the back arrow to return to the

Steering-mounted

selection, display the favourite lists.

previous page.

controls

Media (short press): change the

Deleting a Widget

multimedia source.

Voice control:

Radio: display the list of favourite

To move a Widget to the bin, press and

Short press, system voice commands

stations.

hold it, then drag it to the bin.

(depending on equipment).

Media: display the list of tracks.

Long press, voice commands of the smartphone

Personalising the

connected using Bluetooth^® or Mirror Screen^®

(Apple^®CarPlay^®/Android Auto) via the system.

Applications

instrument panel

Increase volume.

Press the pencil in the "Customize

From the home page, press this button to

Driver Information" part.

access the applications wall.

Decrease volume.

The modification of the organisation of the

Mute the sound: long press on the

From any page, press the touch screen

different Widget is displayed on the instrument

decrease volume button.

with three or more fingers to display the

panel in real time.

Restore the sound by pressing one of the two

applications wall.

A Widget is a reduced window of an

volume buttons.

application or service.

Incoming call (short press): accept the

Help

Access the handbook and watch tutorials.

call.

Media

Call in progress (short press): hang up.

Adding a Widget

Select an audio source or radio station.

Incoming call (long press): refuse the incoming

To add a Widget, press "Widget" on the

Mirror Screen^®

call.

left of the screen.

Smartphone connected with Mirror

Out of call (short press): access the call log of

Screen^®: access to the projected view of

the telephone connected via Bluetooth^®.

Press one of these buttons on the screen.

Apple^®CarPlay^® or Android Auto.

215

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

Smartphone not connected: access the menu

Brazilian, Chinese, Danish, Spanish, Hebrew,

If the system has not taken your command into

allowing you to connect a smartphone.

Italian, Japanese, Dutch, Norwegian, Polish,

account, it will indicate this by a voice message

Navigation

Portuguese, Russian, Swedish, Czech, Turkish)

and an on-screen display.

(depending on equipment)

available with the cellular network and in line

Press the "Settings" application.

Enter navigation settings and choose a

with the language chosen and previously

destination.

configured in the system.

In the list, select the "Voice Assistant" tab.

Use services available in real time, depending on

The system supports two languages for cases

Activate/Deactivate:

equipment.

where the area in which the vehicle is travelling

Voice commands

is not covered by the cellular network.

- "Listen for (OK Peugeot)": to invoke the

(depending on equipment)

These languages, referred to as on-board

voice recognition using the keyword "OK

Use the system or smartphone voice recognition

languages, are downloaded into the system.

Peugeot".

via the system.

If the chosen language has not been

- "Data Usage": to authorise our supplier to

Phone

downloaded, a message on the screen appears

re-use your data in order to let him globally

Telephone not connected: access the

as soon as the cellular network is not connected

improve its capabilities in term of voice

menu allowing you to connect a telephone.

for the first time and offers to download it.

recognition and voice assistance.

Telephone connected: access the call log,

To use this new language in all areas, download

Voice Assistant/Data Usage

contacts and telephone settings.

it beforehand (ignition on without starting the

Vehicle's location and voice recordings

Two connected telephones: access the contents

engine) via the Wi-Fi network.

are not concerned; only textual transcriptions

of the priority telephone with the possibility of

Apply the download procedure displayed on the

of your conversations with the voice assistant

changing the priority of the telephone.

screen.

are kept after to be pseudonymised.

Settings

Downloading this new language removes the

Main settings for the audio system, touch

least used on-board language.

screen and digital instrument panel.

Opening voice recognition

Information - Using the

Voice commands can be used on

Voice commands

system

any screen page, provided there

When voice commands are

are no other sources which take priority in use

activated, say your command after

(reverse, emergency or assistance call,

First steps

the audible signal.

telephone call, other smartphone voice

(depending on equipment)

For commands in several stages, interaction

recognition already launched).

The voice recognition service offers a

takes place with the system to complete the

Choice of opening voice recognition:

choice of 20 languages minimum (French,

initial request.

► Say "OK Peugeot".

German, English (UK), English (US), Arabic,

Some commands self-validate after 7 seconds.

216

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

► Press the button located on the steering

"tune to 88.5"

Navigation

wheel.

Media voice commands are only

available with an USB connection.

Navigation home screen

► Press the touch screen button.

Voice command example for

(depending on equipment)

To ensure that voice commands are

navigation:

always recognised by the system, please

Access to additional videos

"navigate home"

follow these recommendations:

"Navigate me to gabrielle's house"

- Use natural language in a normal tone

"search for public parking nearby"

without breaking up words or raising your

voice.

Depending on the country, give

- After opening voice recognition with the

destination (address) instructions in the

steering wheel-mounted button or the button

language configured for the system.

https://www.tomtom.com/

on the touch screen, always wait for the

PSAGroup-Connected-Nav

"beep" (audible signal) before talking. No

Voice command example for

Press the "Navigation" application to

"beep" sounds when voice recognition is

telephone:

display the navigation home screen.

opened using "OK Peugeot".

"Call Matthew's mobile"

Press "Search" to enter an address or a

- For optimal operation, it is recommended

"call 0113 345 9869"

name.

that you close the windows and the sunroof

"Call jonathan"

Press this button to display the main

(depending on equipment) to avoid any

If there is no telephone connected by

menu for the various options.

external interference, and switch the

Bluetooth^®, a pop-up window appears:

Press this button to display the 3D/2D

ventilation off.

"Connect a telephone by Bluetooth^®", and

mode.

- Before speaking the voice commands, ask

the voice session will be closed.

Select "Sound activated", "Alerts only"

the other passengers not to speak.

and "Silent" with successive presses on

Voice command example for the

this button.

Voice command example for air

weather:

Press the "plus"/"minus" buttons to zoom

conditioning:

"do i need a raincoat"

in/out, or use two fingers on the screen.

"raise the fan speed"

"how is the weather tonight"

"Turn on air conditioning"

"what is today's humidity level"

Main menu

"i'm too hot"

Press the "Navigation" application to

Voice command example for radio

display the navigation home screen.

and media:

Press this button to display the main

"I want to listen to michael jackson"

menu for the various options.

"switch to radio"

217

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

Select "Search" to enter an address,

Regular connection to a secure Wi-Fi

The mobile device is in charging mode when

name or some points of interest.

access point automatically updates the

connected with the USB cable.

Select "Go home" using an address

installed mapping globally.

It is recommended that you use your

previously saved in "Add home".

The mapping is also updated using a cellular

device's original USB cables, preferably

Select "Go to work" using an address

network, depending on version, country of

with a short cable to ensure optimum

previously saved in "My places".

sale, the vehicle's level of equipment, as well

performance.

Select "Recent destinations" to display

as the subscription to connected services and

the latest destinations searched.

options.

To protect the system, do not use a USB

Select "Current trip" to open another

However, using your smartphone's Wi-Fi

hub.

menu and perform various actions for the

and/or cellular networks may incur additional

current planned route.

charges if you exceed your data plan.

Select "My places" for quick access to

These charges, if any, will be passed on to

Bluetooth^® connection

saved places as well as favourite

your telephone operator's bill.

Connecting a mobile device to the vehicle's

destinations.

system via Bluetooth^® provides access to its

Select "My trips" to display your favourite

contents and its "Media" streaming. It also

routes.

Connectivity

enables the Phone function to be activated.

Select "Parking" to display the various

The connection can be initiated either from the

parking options in the area.

Connecting a wired device

mobile device's Bluetooth^® menu or from the

Select "Service station" to display the

vehicle's system, which requires opening the "My

different service stations on the current

by USB

Devices" menu for the first connection.

route or near the current location.

The USB connection of a mobile device allows it

Select "TomTom service" to check the

to be recharged. It makes its authorised media

In some cases, you will need to unlock

network status.

content available to the system (Media content

your device and check the authorisation

Select "Settings" to enter the vehicle type

of iPod^® type).

to synchronise contacts and recent calls.

and to personalise the display, voice

Only one USB socket will allow a Mirror

Some features may not be supported by your

instructions, map options, trip planning, sounds

Screen connection (Apple^®CarPlay^® or

device.

and alerts, and system information.

Android Auto) for the compatible connected

For information on the partial or full

Select this button to display details on

mobile devices and to use some of the device's

compatibility of device models or

software versions as well as legal

applications on the touch screen.

smartphones, please connect to the Brand’s

information. Details of the Open Source software

For more information on the USB socket

national website.

libraries used and their licence URLs.

compatible with the Mirror Screen^® function,

refer to the "Ease of use and comfort - Fittings"

section.

218

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

Pairing procedure from a device

This is to allow the system to make its

allowed to connect. WPA2 encryption level,

Bluetooth^® visible for the connection of a new

equivalent to a domestic level, is required.

From the Bluetooth^® menu on your mobile

device.

device, select the system’s name from the

list of detected devices.

The system is disconnected when the driver’s

Any network already connected to the

door is opened and the ignition is switched

system will reconnect automatically as

In order to make your system’s

off.

soon as it is detected by the system and after

Bluetooth^® visible, first open the "My

having previously activated the Wi-Fi function.

Devices" menu on the system.

Automatic reconnection

Continue the first connection procedure

The Wi-Fi connection of the system to a

The system allows automatic reconnection of

proposed by the system and on the device.

device already connected using a Mirror

devices already connected and detected when a

For example: validating pairing codes.

Screen^® wireless connection is not possible.

user profile is selected.

In this case, favour a Mirror

Pairing procedure from the system

The priority reconnected devices are those which

Screen^® connection using the USB socket.

have been linked to the selected user profile or,

Press the "Settings" application.

failing this, the last connected devices.

In the list, select the "Connectivity" tab.

Device management

Wi-Fi connection

Select "My Devices".

For each device already connected to the

The system has an external Wi-Fi connection

system using a wireless connection (Bluetooth^®

mode for performing system updates.

Select the name of the mobile device that

or wireless Mirror Screen^® connection), it is

Press the "Settings" application.

you want to connect, from:

possible to determine a preferred connection

- The list of known devices (if the device has

mode (depending on the functions the device

already been connected to the system).

In the list, select the "Connectivity" tab.

can support). It is therefore possible to determine

Select "Wi-Fi".

whether the device should be connected using

- The list of detected devices (if the device

a wireless Bluetooth^® connection or a wireless

Activate/Deactivate "Wi-Fi".

has never been connected to the system or

Mirror Screen^® connection each time the system

The system starts a search for

previously deleted from the system).

is started once the profile is chosen.

nearby Wi-Fi networks. This may take a few

Press the "Settings" application.

A mobile device already connected to the

seconds.

system will be able to reconnect

Select the Wi-Fi network to connect to and enter

In the list, select the "Connectivity".

automatically when the vehicle is started,

its password.

Select "My Devices" to display the list of

once the user profile has been selected.

To protect your system, only networks

paired devices.

Automatic reconnection is put on hold as

with a sufficient level of security are

Press this button to manage the

soon as the "My Devices" menu is opened.

connection of a device.

219

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

Choose a connection type then confirm this

First activate the Siri^® function on your

The wireless connection of an Apple^®CarPlay^®

choice by pressing “APPLY".

Apple^® smartphone.

smartphone can be initiated from the "My

If the device fails to connect, refer to the

Devices" menu.

Deleting a device

Apple website to check that the device is

First activate the smartphone’s CarPlay^®

Press the "Settings" application.

compatible with this function.

function.

If the problem persists, delete all saved

In the Bluetooth menu, click on the "i" next to

In the list, select the "Connectivity".

connections on the smartphone and on the

the relevant vehicle and activate CarPlay.

Select "My Devices" to display the list of

system before attempting a new connection.

Press the "Settings" application.

paired devices.

The cable connection requires that you

Press this button.

In the list, select the "Connectivity".

deactivate the CarPlay function in the Settings,

Select "My Devices" to display the device

Bluetooth menu of your smartphone.

Press "DELETE".

to be connected to Apple^®CarPlay^®.

In the Bluetooth menu, click on the "i" next to

Confirm by pressing “YES”.

If the device has already been connected to the

the relevant vehicle and deactivate CarPlay.

system via Bluetooth^®, select the device settings

Some devices that have just been

Connect the smartphone to the system

from the list of known devices and choose

deleted from the system request a

using the USB socket compatible with

Apple^®CarPlay^® as the wireless connection

connection, refuse this request.

Mirror Screen.

mode.

Apple^®CarPlay^® is automatically launched a few

If the device has never been connected to the

seconds after the USB connection has been

system before, it will have to be paired (refer to

Mirror Screen^®

established. In some cases, it may be necessary

the "Bluetooth^® connection" section).

to unlock your device.

The system detects if the smartphone is

When a smartphone is connected using

The smartphone charges when connected by the

compatible with Apple^®CarPlay^® and offers to

Mirror Screen^®, the vehicle's location and

USB cable.

connect to it following the pairing process.

some vehicle data is sent to the smartphone

The cable connection allows you to avoid

Subsequent automatic connection of the

(e.g. brand, left-hand or right-hand drive, day/

disconnections, especially when passing through

smartphone requires activation of the Bluetooth^®

night mode, physical speed).

toll booths.

on your device.

Only one USB socket enables the Mirror

As soon as the connection is established,

Apple^®CarPlay^® smartphone

Screen^® connection (Apple^®CarPlay^®);

press this button to display the

refer to the "Ease of use and comfort

"Apple^®CarPlay^®" interface.

connection

To initiate the smartphone voice

- Fittings" section.

Connecting just one Apple^®CarPlay^® smartphone

commands, press and hold the steering-

It is recommended that you use the device's

can be carried out either by USB cable or using

mounted control button.

original USB cables, preferably with a short

a wireless connection.

cable to ensure optimum performance.

220

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

Android Auto smartphone

smartphone has to be followed for the first

If the device has already been connected to the

connection, with the vehicle stationary.

system via Bluetooth^®, select the device settings

connection

The smartphone charges when connected by the

from the list of known devices and choose

Connecting just one Android Auto smartphone

USB cable.

Android Auto as the wireless connection mode.

can be carried out either by USB cable or using

The cable connection allows you to avoid

The subsequent automatic connection of the

a wireless connection.

disconnections, especially when passing through

smartphone requires activation of Bluetooth^® on

toll booths.

your device.

First install the "Android Auto"

As soon as the connection is established,

application via "Play Store" on your

Only one USB socket enables the Mirror

press this button to display the "Android

smartphone.

Screen^® connection (Android Auto); refer

Auto" interface.

The "Android Auto" function requires a

to the "Ease of use and comfort - Fittings"

To initiate the smartphone voice

compatible smartphone.

section.

commands, press and hold the steering-

If the device fails to connect, refer to the

It is recommended that you use the device's

mounted control button.

Android Auto website to check that the device

original USB cables, preferably with a short

is compatible with this function.

cable to ensure optimum performance.

If the problem persists, delete all saved

Media

connections on the smartphone and on the

The wireless connection of an Android Auto

system before attempting a new connection.

smartphone can be initiated from the "My

Changing source

To ensure an optimum wireless connection,

Devices" menu.

we recommend avoiding placing your

First activate the smartphone’s Android Auto^®

Press the "Media" application.

smartphone too close to other Wi-Fi networks

wireless function, in the Settings menu of the

to which it can connect automatically.

"Android Auto" application of your smartphone.

Press this button to change source (radio,

Press the "Settings" application.

audio streaming via a USB socket,

The cable connection requires that you

Bluetooth^® or Mirror Screen^®).

deactivate the Android Auto wireless function,

Using the steering-mounted controls,

In the list, select the "Connectivity" tab.

in the Settings menu of the "Android Auto"

Select "My Devices" to display the device

press this button to change source.

application of your smartphone.

to be connected to Android Auto.

Connect the smartphone to the system

Selecting a radio station

If the device has never been connected to the

using the USB socket compatible with

system before, it will have to be paired (refer to

Press the "Media" application.

Mirror Screen^®.

the "Bluetooth^® connection" section).

Android Auto is automatically launched a few

The system detects if the smartphone is

In the list, select the "Player" tab.

seconds after the USB connection has been

compatible with Android Auto and offers to

Press one of the buttons to

established. A validation procedure on the

connect to it following the pairing process.

perform an automatic search for

radio stations.

221

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

Storing takes place via a short or long

Press this button to change the waveband

Move the slider to manually search for

press on one of these buttons, or a long

(FM - AM - DAB) according to the country

frequencies up or down.

press on an existing favourite radio station,

of sale.

which will be replaced.

Press this button.

Press this button to return to the previous

Activating traffic

page.

announcements

Enter the frequency values using the

This function gives priority to listening to Traffic

virtual keypad.

Automatic search for radio

announcements alert messages. To be active,

Press this button to confirm.

stations

this function needs good reception of a radio

Via the "Media" application.

station that transmits this type of message.

A list of stations is available by pressing the

Press the "Media" application.

While traffic information is being broadcast, the

“Stations” tab.

current radio station is automatically interrupted

Press “Mute” to activate/deactivate the

In the list, select the "Stations" tab.

so that the message can be heard. Normal radio

sound.

The search is carried out automatically.

listening resumes as soon as the message is

Radio reception may be affected by the

finished.

use of electrical equipment not approved

Activating radio station

Press the "Media" application.

by the Brand, such as a charger with USB

tracking

socket connected to the 12 V socket.

In the list, select the "Settings” tab.

The system changes frequency automatically to

The exterior environment (hills, buildings,

Activate “Traffic Announcement (TA)”.

obtain better reception.

tunnels, basement car parks, etc.) may block

Press the "Media" application.

reception, including in RDS mode. This

The lighting of the slider confirms that the

phenomenon is normal in the propagation

function is activated.

In the list, select the "Settings” tab.

of radio waves and does not indicate any

Activate “Radio Station Tracking”.

malfunction of the system.

Audio streaming

The streaming function allows you to listen to

The lighting of the slider confirms that the

the audio stream coming from the smartphone(s)

Storing a radio station

function is activated.

connected via Bluetooth^®, USB (iPod^® type) or

Select a station.

Mirror Screen^®.

Changing the waveband

Press the "Media" application.

First adjust the volume on the portable device (to

Press the "Media" application.

a high level).

In the list, select the "Player” tab.

Then adjust the volume of the system.

Press the "Radio Favorites" button.

In the list, select the "Player" tab.

222

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

If playback does not start, it may be necessary to

Press the "Media" application.

We recommend using the original USB

start the audio playback from the smartphone.

cable for the portable device.

Control is from the portable device or by using

In the list, select the "Settings" tab.

the system's touch buttons.

Via the Settings application

Phone

Once connected in streaming mode, the

Press the "Settings" application.

smartphone is considered to be a media

source.

Receiving a call

In the list, select the "Audio and Radio" tab.

An incoming call is announced by a ring and a

It is possible to configure:

display overlaid on the screen.

Playing a track

- Sound Settings.

Accepting the call:

- Radio Settings.

Press the "Media" application.

briefly press the telephone button on the

- Volume Settings.

steering-mounted controls to accept an

If several devices are connected, press

Information and advice

incoming call.

this button to select one.

Once the device is connected, browsing through

The system supports USB Mass Storage devices

Press this touch screen button.

the files is possible by pressing the "Playlist" or

or Apple^® devices via the USB sockets. The

"Library" button.

adapter cable is not supplied.

Ending the call:

Short press: go to the previous/

Devices are managed using the audio system

press and hold

next track.

controls.

Long press: fast-forward/rewind in a track.

The system will only play audio files with ".wma,

...the telephone button on the steering-

Repeat the current title or the list of

.aac, .flac, .ogg, .mp3" file extensions, at bit rates

mounted controls to refuse the call.

selected titles.

between 32 Kbps and 320 Kbps.

Random track playback.

It also supports VBR (Variable Bit Rate) mode.

Press this touch screen button.

No other file types (".mp4", etc.) can be read.

Sound deactivation/reactivation.

".wma" files must be of the WMA 9 standard.

Press this button on the touch screen to

The supported sampling rates are 32, 44 and

send an automatic message indicating

48 KHz.

that you are driving.

Configuring audio and radio

To avoid reading and display problems, we

recommend choosing file names less than 20

settings

Making a call

characters long that do not contain any special

Audio settings can be accessed in 2 different

characters (e.g. “ ? . ; ù).

Using the telephone is strongly

ways.

Use only USB memory sticks in FAT32 format

discouraged while driving.

Via the Media application

(File Allocation Table).

Park the vehicle.

223

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

Making a call using the numeric

Organising the contact list

It is possible to configure:

keypad

- the screen colours associated with the interior

Press the "Phone" application.

ambient lighting. Refer to the "Ease of use and

Press the "Phone" application.

comfort" section.

In the list, select the “Settings” tab to display the

- the sound ambience.

In the list, select the “Keypad” tab then dial the

telephone-related settings.

- the visual welcome and goodbye animations.

number.

Choose to list the contacts starting with

- the screen transition animations.

Press this button to make the call.

their first or last name.

Managing the system

Connecting two phones

Making a call using the list of recent

connectivity

calls

The system allows two phones to be

Press the "Settings" application.

connected simultaneously:

Press the "Phone" application.

- 2 via Bluetooth^® connection.

In the list, select the "Connectivity" tab.

In the list, select the "Calls" tab.

It is possible to manage:

- 1 via Bluetooth^® connection and 1 via Mirror

- The Bluetooth^® connection.

Screen^® connection.

Briefly press

- The Mirror Screen^® smartphone connections

Display and content priority is given to the last

...the telephone button on the steering-

(Apple^®CarPlay^®/Android Auto).

phone used.

mounted controls.

- The Wi-Fi connection.

Select and call one of the most recent numbers

- The privacy mode.

To change the priority of the phone:

called in the list.

Press the "Phone" application.

Configuring the system

It is always possible to make a call

Press this button to change the priority of

Press the "Settings" application.

directly from the telephone; as a safety

measure, first park the vehicle.

the phone.

In the list, select the "System” tab.

It is possible to configure:

Calling a contact

Settings

- the language.

Press the "Phone" application.

- the date & time.

Configuring the screen

- the unit of distance and consumption

In the list, select the "Contacts” tab.

(kWh/100 miles - miles, mi/kWh - miles, km/kWh

display

Select the desired contact in the displayed list.

- km).

Press the "Settings" application.

Call the contact by selecting one of the

- the temperature unit (Fahrenheit, Celsius).

contact's phone numbers.

In the list, select the "Customization" tab.

224

CarManuals2.com

PEUGEOT i-Connect Advanced - PEUGEOT i-Connect

It is also possible to reset the system

The system does not automatically

Access to sections dedicated to the various

configuration.

change between winter and summer time

audio equipment and telematics systems.

(depending on the country of sale).

Contents

Selecting the language

Access to subjects via the main sections

Select "Language" to change the

of the handbook.

language.

Help

Press the desired language.

Visual search

Press the "Help" application.

Press Visual search.

Press the back arrow to return to the

In the list, select the “User Manual” tab to

previous page.

Press one of the pictures located at the bottom

consult the vehicle’s handbook.

of the screen.

Setting the date and time

Press one of the bullet points in the

In the list, select the “Tutorials” tab to watch

Select “Date and Time” to modify the date and

enlarged view.

explanatory videos for a quick start on screen

time.

There are two cases:

management, certain driving aids and voice

“Automatic Date and Time” is activated

- Direct display of the subject, if only one

recognition.

by default, so that the setting is made

subject is associated with the bullet point.

automatically according to your geolocation.

- Display of a list of subjects, if several subjects

User Manual

To adjust manually, deactivate “Automatic Date

are associated with the bullet point.

Select the display language.

and Time”.

Press the “Select Time Zone” field then define

Indicator lamps

a time zone.

The handbook home page is displayed.

Press Indicator lamps.

It presents the different possibilities for accessing

Press the back arrow to return to the

the information sought:

previous page.

The mosaic of warning/indicator lamps is

Visual search

Press the “Time Settings” line then set the time.

displayed.

Access to subjects via pictures

Press "OK" to confirm.

The warning/indicator lamps are sorted by

representing the exterior and interior of the

colour.

vehicle.

Press the “Date” line then set the date.

Press the warning/indicator lamp concerned; the

Indicator lamps

Press "OK" to confirm.

corresponding content is displayed.

Access to the descriptions/operation of

Back to the mosaic of warning/indicator

the instrument panel warning/indicator lamps.

Select the Time Format (12h/24h).

lamps.

System

Select the Date Format.

225

CarManuals2.com

Vehicle data recording and privacy

- Environmental conditions (e.g. temperature,

identification number and used if necessary.

Vehicle data recording

rain sensor, distance sensor).

The personnel working for the servicing network

and privacy

As a general rule, this data is temporary, is

(e.g. garages, manufacturers) or third parties

Electronic control units are installed in your

not stored for longer than one operating cycle

(e.g. roadside assistance agents) may read

vehicle. These control units process data

and is only used within the vehicle itself. The

the vehicle's data. This also applies to work

received from the vehicle's sensors, for example,

control units often record this data (including the

carried out under warranty and quality assurance

or data they generate themselves or exchange

vehicle's key). This function allows either the

measures.

with each other. Some of these control units are

temporary or permanent storage of information

This data is generally read via the OBD

required for the correct operation of your vehicle,

about the state of the vehicle, stresses on

(On-Board Diagnostics) port fitted by law to

some others assist you while driving (driving or

components, servicing requirements, as well as

the vehicle. It is used to report on the technical

manoeuvring aids), while others provide comfort

events and technical errors.

state of the vehicle or its components and

or infotainment functions.

Depending on the vehicle's equipment level, the

facilitates the diagnosis of malfunctions, in

The following contains general information about

data stored is as follows:

compliance with warranty obligations and for

how data is processed within the vehicle.

- Operating state of system components

quality improvement. This data, in particular the

You will find additional information about the

(e.g. filling level, tyre pressures, battery charge

information relating to stress on components,

specific data which is downloaded, stored

status).

technical events, operator errors and other

and transmitted to third parties and what it is

- Faults and malfunctions in important system

malfunctions, is sent to the Manufacturer, if

used for in your vehicle under the keyword

components (e.g. lamps, brakes).

necessary, along with the vehicle's identification

"Data protection". This information is directly

- System reactions in specific driving situations

number. The Manufacturer's liability may also be

associated with the references for the functions

(e.g. deployment of an airbag, triggering of

engaged. The Manufacturer may also use the

in question contained in the corresponding

stability control and braking systems).

operating data taken from the vehicle for product

vehicle handbook, or in the general terms and

- Information about events which have

recalls. This data may also be used to check the

conditions of sale.

damaged the vehicle.

customer's warranty and any claims made under

This information is also available online.

- For electric and rechargeable hybrid vehicles,

warranty.

the traction battery charge level and the

Any malfunctions stored in the vehicle may be

Vehicle operating data

estimated driving range.

reset by an after-sales service company during

In particular circumstances (e.g. if the vehicle

servicing or repair work, or at your request.

The control units process the data used for the

has detected a malfunction), it may be necessary

operation of the vehicle.

to record data which would otherwise simply not

This data includes, for example:

be stored.

- Information about the state of the vehicle

When taking your vehicle in for servicing

(e.g. speed, travel time, lateral acceleration,

(e.g. repairs, maintenance), the stored operating

wheel rotation rate, fastened seat belts display).

data may be read along with the vehicle's

227

CarManuals2.com

Vehicle data recording and privacy

Comfort and infotainment

online services in line with the settings that you

Online services

have selected.

If your vehicle is connected to a wireless

functions

network, data can be exchanged between

Comfort settings and personalised settings

Smartphone integration

your vehicle and other systems. Connection

may be saved in the vehicle and modified or

(e.g. Android Auto^® or

to a wireless network is made possible via a

reinitialised at any time.

transmitter located in your vehicle or a mobile

Depending on the vehicle's equipment level, this

Apple^®CarPlay^®)

device that you have provided (e.g. smartphone).

may include:

If your vehicle is equipped accordingly, you can

The online services can be used via this wireless

- Seat and steering wheel position settings.

connect your smartphone or another mobile

connection. These include online services and

- Chassis and air conditioning settings.

device to the vehicle in order to operate it using

applications (apps) provided to you by the

- Personalised settings such as the interior

the vehicle's integrated controls. Images and

Manufacturer or other suppliers.

lighting.

sounds from the smartphone can be transmitted

You can enter your own data into the functions

through the audio and telematics system.

Exclusive services

of your vehicle's audio and telematic system, as

Specific information is simultaneously sent

As regards the Manufacturer's online services,

part of the selected functionalities.

to your smartphone. Depending on the type

the corresponding functions are described by

Depending on the vehicle's equipment level, this

of integration, this includes data such as location,

the Manufacturer in an appropriate medium

may include:

day/night mode and other general information

(e.g. handbook, Manufacturer's website) and the

- Multimedia data such as music, videos or

about the vehicle. For more information, please

information about data protection is provided.

photos to be read by an integrated multimedia

refer to the user instructions for the vehicle or the

Personal data may be used for online services.

system.

audio and telematics system.

The exchange of data for this purpose takes

- Address book data to be used with an

Integrating a smartphone allows you to use

place over a secure connection, using for

integrated hands-free system or with an

its applications, such as a navigation app or

example the Manufacturer's dedicated computer

integrated navigation system.

music player. No other integration between

systems. The collection, processing and use of

- Entered destinations.

the smartphone and the vehicle is possible, in

personal data for the development of services

- Data regarding the use of online services.

particular active access to vehicle data. How the

are carried out solely on the basis of a legal

This data for the comfort and infotainment

data is processed subsequently is determined

authorisation, for example in the case of a

functions may be stored locally in the vehicle

by the supplier of the application being used.

legal emergency call system or a contractual

or saved to a device that you have connected

The ability the change settings depends on the

agreement or else under a consent agreement.

to the vehicle (e.g. smartphone, USB memory

application in question and on the operating

You can activate or deactivate the services and

stick or MP3 player). Data that you have entered

system installed on your smartphone.

functions (some may be chargeable) and, in

yourself may be deleted at any time.

some cases, the vehicle's entire connection to

This data may also be transmitted outside the

the wireless network. This does not include the

vehicle at your request, particularly when using

228

CarManuals2.com

Alphabetical index

3D digital instrument panel 

Airbags, lateral 

 79-80

Braking 

 104

Air conditioning 

 48-49, 52

Braking assistance system 

 72-73

Air conditioning, automatic 

Braking, automatic emergency 

 131-133

Air conditioning, dual-zone automatic 

Braking, dynamic emergency 

 97-98

Air intake 

Brightness 

 207

ABS 

Air vents 

Bulbs (changing) 

 183-185

Accelerated charging unit (Wallbox) 

 149

Alarm 

 38-39

Accessories 

Anti-lock braking system (ABS) 

 72-73

Accessories, electrical 

Antitheft / Immobiliser 

Active Safety Brake 

 131-133

Applications 

AdBlue® 

 21, 170

Assistance call 

 70-71

Capacity, fuel tank 

 144

AdBlue® tank 

 171

Assistance, emergency braking 

 73, 133

Cap, fuel filler 

 144

Additive, Diesel 

 168

Audio streaming (Bluetooth) 

 202, 222

Care of the bodywork 

 173

Adjusting headlamps 

Central locking 

Adjusting head restraints 

Changing a bulb 

 183-185

Adjusting seat 

 43-44

Changing a fuse 

 185

Adjusting the air distribution 

Changing a wheel 

 180

Adjusting the air flow 

Battery, 12 V 

 163, 168, 185-188

Changing a wiper blade 

 65-66

Adjusting the date 

 208

Battery, ancillaries 

 185-186

Changing the remote control battery 

Adjusting the headlamp beam height 

Battery, charging 

 186-187

Changing to free-wheeling 

 172, 189

Adjusting the height and reach

Battery, remote control 

Charge level indicator (Electric) 

of the steering wheel 

Blanking screen (snow shield) 

 162

Charger, induction 

Adjusting the lumbar support 

Blind 

 41-42

Charger, wireless 

Adjusting the seat angle 

Blind spot monitoring 

 129

Charging cable 

 151

Adjusting the temperature 

BlueHDi 

 21, 167, 176

Charging cable (Electric) 

 149

Adjusting the time 

 208, 225

Bluetooth (hands-free) 

 202-203, 219

Charging connector

Advanced Grip Control 

Bluetooth (telephone) 

 202-203, 219-220

(Electric) 

 149, 154, 156-157

Advice on care and maintenance 

 147, 173

Bodywork 

 173

Charging flap (Electric) 

 149, 154, 156-157

Advice on driving 

 8, 91-92

Bonnet 

 164-165

Charging system (Electric) 

 5, 9, 146, 166

Airbags 

 78, 80, 82

Boot 

 38, 58

Charging the traction battery

Airbags, curtain 

 79-80

Brake discs 

 169

(Electric) 

 146, 154, 156-157

Airbags, front 

 79-80, 82

Brakes 

 169

230

CarManuals2.com

Alphabetical index

Charging the traction battery (Rechargeable

Control stalk, wipers 

 64-67

Display screen, instrument panel 

 10-11

hybrid) 

Control unit 

 149, 151

Domestic charging 

 151

CHECK 

Courtesy lamp, front 

Domestic charging (Electric) 

 156-157, 195

Checking the engine oil level 

Courtesy lamps 

 56-57

Doors 

Checking the levels 

 166-167

Cruise control 

 115, 117-119

Drive Assist Plus 

 119

Checking tyre pressures

Cruise control, adaptive 

 119

Drive,

(using the kit) 

 178, 180

Cruise control, adaptive with Stop function 

 115

electric 

 5, 9, 28, 146, 159, 166, 186, 189, 195

Checks 

 165, 168-170

Cruise control by speed limit recognition 

 115

Driver’s attention warning 

 135

Checks, routine 

 168-169

Drive selector (Electric) 

 103

Child lock 

Driving 

 91-92

Children 

 77, 83-84

Driving aids camera (warnings) 

 110

Children (safety) 

Driving aid shortcuts 

 111

Child seats 

 77, 80-82, 84

DAB (Digital Audio Broadcasting) -

Driving aids (recommendations) 

 110

Child seats, conventional 

 84, 86, 88

Digital radio 

 201

Driving economically 

Child seats, i-Size 

 84, 86, 88

Date (setting) 

 208, 225

Driving modes 

 75, 104

Child seats, ISOFIX 

 83-84, 86, 88

Daytime running lamps 

 60, 184

Driving modes (Electric) 

 105

Cleaning (advice) 

 147, 173-174

Deactivating the passenger airbag 

 79, 82

Dynamic stability control (DSC) 

Closing the boot 

 33, 38

Deadlocking 

 31, 33

Closing the doors 

 33-34, 37

Deferred charging 

Collision Risk Alert 

 131-132

Deferred charging (Electric) 

 28, 149, 154, 157

Configuration, vehicle 

 11, 26-27

Deferred charging (Rechargeable hybrid) 

Connection, Android Auto 

 205

Defrosting 

 46, 52

EBFD 

Connection, Apple CarPlay 

 205

Defrosting, front 

Eco-driving (advice) 

Connection, Bluetooth 

 202-203, 219-220

Defrosting, rear screen 

ECO mode 

 104-105

Connectivity 

 224

Demisting 

 46, 52

Electric windows 

Consumptions 

Demisting, front 

Electronic brake force distribution

Container, AdBlue® 

 170-171

Demisting, rear 

(EBFD) 

 72-73

Control, emergency boot release 

Diagnosis, vehicle 

Emergency braking assistance (EBA) 

Control, emergency door 

Dials and gauges 

 10-11

Emergency call 

 70-71

Control, heated seats 

Dimensions 

 196

Emergency switching off 

 95-96

Controls, steering mounted 

 101-102

Dipstick 

 20, 166

Emergency warning lamps 

 69, 176

Control stalk, lighting 

 59-60

Direction indicators (turn signals) 

 60, 184

Emissions control system, SCR 

 22, 170

231

CarManuals2.com

Alphabetical index

Energy economy (mode) 

 163

Floor, boot, adjustable 

Headlamps, main beam 

 63, 184

Energy economy mode 

 163

Fluid, brake 

 167

Head restraints, front 

Energy flows 

Fluid, engine coolant 

 167

Head restraints, rear 

 47-48

Energy recovery 

 22, 104

Foglamp, rear 

Heating 

Engine 

 170

Foglamps, rear 

 185

Heating, programmable 

 28, 53

Engine compartment 

 165

Folding the rear seats 

 47-48

High voltage 

 146

Engine, Diesel 

 144, 165, 176, 194

Frequency (radio) 

 222

Hill Assist Descent Control (HADC) 

Engine, petrol 

 165, 193

Fuel 

 8, 144

Hill start assist 

 105-106

Engines 

 192-194

Fuel consumption 

 8, 22

Histogramme, fuel consumption 

Environment 

 8, 36, 92

Fuel level, low 

 144

Horn 

ESC (electronic stability control) 

Fuel (tank) 

 144-145

Event data recorder 

Fuses 

 185

Expanded traffic sign recognition 

 115

Exterior lighting 

Ignition 

 95, 224

Ignition on 

Gauge, fuel 

 144

Immobiliser, electronic 

Gearbox, automatic 

 99, 101-103, 169, 186

Indicator, AdBlue® range 

Fatigue detection 

 134-135

Gearbox, manual 

 99, 169

Indicator, coolant temperature 

Favourite driving functions 

 111

Gear lever 

 106

Indicator, engine oil level 

Filling the AdBlue® tank 

 167, 171

Gear lever, manual gearbox 

Indicators, direction 

 60, 184

Filling the fuel tank 

 144-145

Gear shift indicator 

 106

Indicator, service 

Filter, air 

 168

Glove box 

Inflating tyres 

 169, 196

Filter, oil 

 168

Inflating tyres and accessories

Filter, particle 

 168

(using the kit) 

 178, 180

Filter, passenger compartment 

 48, 168

Information, vehicle 

 227

Fitting a wheel 

 181-182

Infrared camera 

 110

Fitting roof bars 

 161-162

Hazard warning lamps 

 69, 176

Instrument panel 

 10-11, 25, 111

Fittings, boot 

Headlamps (adjustment) 

Instrument panel, matrix 

Fittings, interior 

 53-54

Headlamps, automatic dipping 

 63-64

ISOFIX mountings 

 83, 86, 88

Flap, fuel filler 

 144-145

Headlamps, automatic operation 

Flashing indicators 

 60, 184

Headlamps, dipped beam 

 184

232

CarManuals2.com

Alphabetical index

Level, engine coolant 

 21, 167

Menu, main 

Level, engine oil 

 20, 166

Menus (audio) 

 198-199

Jack 

 177-178, 180

Levels and checks 

 165-167

Menu, shortcuts 

Jump starting 

 187

Level, screenwash fluid 

 65, 167

Minimum traction battery charge level

Light-emitting diodes - LEDs 

 60, 184

(Electric) 

Lighting, boot 

Mirror, rear view 

Lighting dimmer 

 24-25

Mirrors, door 

 45, 52, 129

Lighting, exterior 

 59, 62

Mirror, vanity 

Key 

 30, 32, 35

Lighting, guide-me home 

 31, 62

Misfuel prevention 

 145

Key, electronic 

 33-34

Lighting, interior 

 56-57

Mobile application 

 28, 53, 157

Keyless Entry and Starting 

 32-33, 94-95

Lighting, mood 

Motor, electric 

 95, 166, 195

Key not recognised 

 95-96

Lighting, welcome 

Mountings, ISOFIX 

 83, 86, 88

Key with remote control 

 30, 93

 161

Kit, hands-free 

 202-203, 219

Load reduction mode 

 164

Kit, puncture repair 

 177

Locating your vehicle 

Kit, temporary puncture repair 

 176-178, 180

Locking 

 31-33

Klaxon 

Locking from the inside 

Normal mode 

 105

Locking the doors 

 34-35

Log, alerts 

Lumbar 

Labels, identification 

 196

Obstacle detection 

 136

Lamps, parking 

Oil change 

 166

Lamps, rear 

 185

Oil consumption 

 166

Lamps with Full LED technology 

Mains socket (domestic network) 

 149

Oil, engine 

 166

Lane keeping assist 

 127

Maintenance (advice) 

 147, 173

On-board tools 

 58, 176-177

Lane positioning assist 

 119, 123-125

Maintenance, routine 

 111, 168-170

Opening the bonnet 

 164-165

Leather (care) 

 174

Manoeuvring aids (recommendations) 

 110

Opening the boot 

 33, 38

LEDs - Light-emitting diodes 

 60, 184

Map reading lamps 

Opening the doors 

 33, 37

Level, AdBlue® 

 167

Markings, identification 

 196

Level, brake fluid 

 167

Massage function 

Level, Diesel additive 

 168

Mat 

 55, 111

233

CarManuals2.com

Alphabetical index

Removing a wheel 

 181-182

Removing the mat 

Pads, brake 

 169

Radar (warnings) 

 110

Replacing bulbs 

 183-185

Paint 

 173, 196

Radio 

 199-200, 221-222

Replacing fuses 

 185

Paint colour code 

 196

Radio,

Replacing the air filter 

 168

Parking brake 

 96, 169

digital (Digital Audio Broadcasting - DAB) 

 201

Replacing the oil filter 

 168

Parking brake, electric 

 96-98, 169

Range, AdBlue® 

 21, 167

Replacing the passenger

Parking (sensors) 

 136

RDS 

 200

compartment filter 

 168

Parking sensors, audible and visual 

 136

Reading lamps 

Reservoir, screenwash 

 167

Parking sensors, front 

 137

Reading lamps, touch-sensitive 

 56-57

Resetting the trip 

Parking sensors, rear 

 136

Rear bench seat 

Reversing camera 

 110, 138-140

Parking sensors, side 

 137

Rear screen (demisting) 

Road sign recognition 

 112

Passenger compartment temperature

Rechargeable hybrid engine 

Roof bars 

 161-162

pre-conditioning (Electric) 

 28, 53

Rechargeable hybrid system 

Roof, opening 

 41-42

Pedestrian horn (Electric) 

 69, 92

Recharging the battery 

 186-187

Running out of fuel (Diesel) 

 176

Personalisation 

Recharging the traction battery 

 151

Plates, identification 

 196

Recharging the traction battery

Player, Apple® 

 202

(Electric) 

 146, 154, 156-157

Player, USB 

 201

Recirculation, air 

Port, USB 

 54, 201, 204

Recorder, trip distance 

Safety, children 

 79-84

Power 

Reduction of electrical load (mode) 

 164

Saturation of the particle filter (Diesel) 

 168

Power indicator (Electric) 

Regeneration of the particle filter 

 168

Screens, very cold conditions 

 162

Power indicator (Rechargeable hybrid) 

Regenerative braking (deceleration by engine

Screenwash 

Pressures, tyres 

 169, 178, 180, 196

braking) 

 103-104

Screenwash, front 

Pre-tensioning (seat belts) 

Reinitialising the remote control 

Screenwash, rear 

Priming the fuel system 

 176

Reinitialising the under-inflation

SCR (Selective Catalytic Reduction) 

 22, 170

Profiles 

 212

detection system 

 109

Seat angle 

Protecting children 

 79-84

Reminder, key in ignition 

Seat belts 

 76-77

Proximity Keyless Entry and Start 

Reminder, lighting on 

Seat belts, rear 

Public fast charging station 

 149, 156

Remote control 

 30-35

Seats, electric 

Puncture 

 178, 180

Remotely operable functions

Seats, front 

 43-44

(Electric) 

 28, 53, 157

Seats, heated 

234

CarManuals2.com

Peugeot 2008 (2024 year). Manual in english - page 3