Nissan Quest E52. Manual - part 1086

SEC-34

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

THEFT ALM

THEFT ALM : CONSULT Function (BCM - THEFT)

INFOID:0000000009650701

WORK SUPPORT

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

P RANGE

This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation

ENGINE SW ILLUMI

This test is able to check push-button ignition switch illumination operation
• On: Operate
• Off: Non-operation

LOCK INDICATOR

This test is able to check LOCK indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation

ACC INDICATOR

This test is able to check ACC indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation

IGNITION ON IND

This test is able to check ON indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation

HORN

This test is able to check horn operation
• On: Operate
• Off: Non-operation

TRUNK/BACK DOOR

NOTE:
This item is displayed, but cannot be used

POWER SLIDE DOOR

This test is able to check automatic siding door operation
• RR PSD ON: Auto open/close operate
• RL PSD ON: Auto open/close operate

Test item

Description

Service Item

Description

SECURITY ALARM SET

This mode is able to confirm and change security alarm ON-OFF setting.

THEFT ALM TRG

The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.

Monitored Item

Description

REQ SW -DR

Indicates [ON/OFF] condition of door request switch (driver side).

REQ SW -AS

Indicates [ON/OFF] condition of door request switch (passenger side).

REQ SW -RR

NOTE:
This is displayed even when it is not equipped.

REQ SW -RL

NOTE:
This is displayed even when it is not equipped.

REQ SW -BD/TR

Indicates [ON/OFF] condition of back door request switch.

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch

UNLK SEN -DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

DOOR SW-DR

Indicates [ON/OFF] condition of front door switch (driver side).

DOOR SW-AS

Indicates [ON/OFF] condition of front door switch (passenger side).

DOOR SW-RR

Indicates [ON/OFF] condition of rear door switch RH.

DIAGNOSIS SYSTEM (BCM)

SEC-35

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

ACTIVE TEST

IMMU

IMMU : CONSULT Function (BCM - IMMU)

INFOID:0000000009650702

WORK SUPPORT

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

DOOR SW-RL

Indicates [ON/OFF] condition of rear door switch LH.

DOOR SW-BK

Indicates [ON/OFF] condition of back door switch.

CDL LOCK SW

Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.

CDL UNLOCK SW

Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.

KEY CYL LK-SW

Indicates [ON/OFF] condition of lock signal from door key cylinder.

KEY CYL UN-SW

Indicates [ON/OFF] condition of unlock signal from door key cylinder.

TR/BD OPEN SW

Indicates [ON/OFF] condition of back door opener switch.

TRNK/HAT MNTR

NOTE:
This is displayed even when it is not equipped.

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

NOTE:
This is displayed even when it is not equipped.

Monitored Item

Description

Test Item

Description

THEFT IND

This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.

VEHICLE SECURITY HORN

This test is able to check horns operation.
Horns are activated for 0.5 seconds after “ON” on CONSULT screen is touched.

HEADLAMP(HI)

This test is able to check headlamp operation.
Headlamps are activated for 0.5 seconds after “ON” on CONSULT screen is touched.

FLASHER

This test is able to check hazard warning lamp operation.
Hazard warning lamps are activated after “ON” on CONSULT screen is touched.

Service item

Description

CONFIRM DONGLE ID

It is possible to check that dongle unit is applied to the vehicle.

Monitor item 

Content

CONFRM ID ALL

Indicates [YET] at all time.
Switches to [DONE] when a registered Intelligent Key backside is contacted to push-button igni-
tion switch.

CONFIRM ID4

CONFIRM ID3

CONFIRM ID2

CONFIRM ID1

NOT REGISTERED

Indicates [ID OK] when key ID that is registered is received or is not yet received.
Indicates [ID NG] when key ID that is not registered is received.

SEC-36

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST

TP 4

Indicates the number of IDs that are registered.

TP 3

TP 2

TP 1

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

Monitor item 

Content

Test item

Description

THEFT IND

This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.

DIAGNOSIS SYSTEM (IPDM E/R)

SEC-37

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

DIAGNOSIS SYSTEM (IPDM E/R)

CONSULT Function (IPDM E/R)

INFOID:0000000009982301

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with IPDM E/R.

SELF DIAGNOSTIC RESULT

Refer to 

PCS-24, "DTC Index"

.

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Diagnosis mode

Description

Ecu Identification

Allows confirmation of IPDM E/R part number.

Self Diagnostic Result

Displays the diagnosis results judged by IPDM E/R.

Data Monitor

Displays the real-time input/output data from IPDM E/R input/output data.

Active Test

IPDM E/R can provide a drive signal to electronic components to check their operations.

CAN Diag Support Monitor

The results of transmit/receive diagnosis of CAN communication can be read.

Monitor Item

[Unit]

MAIN SIG-

NALS

Description

MOTOR FAN REQ
[1/2/3/4]

×

Displays the value of the cooling fan speed signal received from ECM via CAN com-
munication.

AC COMP REQ
[Off/On]

×

Displays the status of the A/C compressor request signal received from ECM via 
CAN communication.

TAIL&CLR REQ
[Off/On]

×

Displays the status of the position light request signal received from BCM via CAN 
communication.

HL LO REQ
[Off/On]

×

Displays the status of the low beam request signal received from BCM via CAN com-
munication.

HL HI REQ
[Off/On]

×

Displays the status of the high beam request signal received from BCM via CAN 
communication.

FR FOG REQ
[Off/On]

×

Displays the status of the front fog light request signal received from BCM via CAN 
communication.

FR WIP REQ
[Stop/1LOW/Low/Hi]

×

Displays the status of the front wiper request signal received from BCM via CAN 
communication.

WIP AUTO STOP
[STOP P/ACT P]

×

Displays the status of the front wiper stop position signal judged by IPDM E/R.

WIP PROT
[Off/BLOCK]

×

Displays the status of the front wiper fail-safe operation judged by IPDM E/R.

IGN RLY1 -REQ
[Off/On]

Displays the status of the ignition switch ON signal received from BCM via CAN com-
munication.

IGN RLY
[Off/On]

×

Displays the status of the ignition relay judged by IPDM E/R.

PUSH SW
[Off/On]

Displays the status of the push-button ignition switch judged by IPDM E/R.

INTER/NP SW
[Off/On]

Displays the status of the shift position judged by IPDM E/R.

ST RLY CONT
[Off/On]

Displays the status of the starter relay status signal received from BCM via CAN 
communication.

IHBT RLY -REQ
[Off/On]

Displays the status of the starter control relay signal received from BCM via CAN 
communication.