Nissan Note E12. Manual - part 553

SEC-64

< DTC/CIRCUIT DIAGNOSIS >

P1612 CHAIN OF ECM-IMMU

P1612 CHAIN OF ECM-IMMU

DTC Logic

INFOID:0000000009567413

DTC DETECTION LOGIC

NOTE:

• If DTC P1612 is displayed with DTC U1000 (for BCM), first perform the trouble diagnosis for DTC U1000.

Refer to 

BCS-57, "DTC Logic"

.

• If DTC P1612 is displayed with DTC U1010 (for BCM), first perform the trouble diagnosis for DTC U1010.

Refer to 

BCS-58, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in Self Diagnostic Result mode of ENGINE using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-64, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009567414

1.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-67, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

Does the engine start?

YES

>> Inspection End.

NO

>> GO TO 2.

2.

REPLACE ECM

1. Replace ECM.

Refer to 

EC-338, "Removal and Installation"

.

2. Perform “ADDITIONAL SERVICE WHEN REPLACING ECM”.

Refer to 

EC-111, "Work Procedure"

.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1612

CHAIN OF ECM-IMMU

Inactive communication between ECM 
and BCM

• Harness or connectors

(The CAN communication line is open or 
shorted.)

• BCM 
• ECM

B2192 ID DISCORD, IMMU-ECM

SEC-65

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2192 ID DISCORD, IMMU-ECM

DTC Logic

INFOID:0000000009567415

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-65, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009567416

1.

PERFORM INITIALIZATION

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CONSULT

Immobilizer mode and follow the on-screen instructions.
Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> Inspection End.

NO

>> GO TO 2.

2.

CHECK SELF-DIAGNOSIS RESULT

1. Select “Self Diagnostic Result” mode of “BCM” using CONSULT.

2. Erase DTC.

3. Perform DTC CONFIRMATION PROCEDURE for DTC B2192. Refer to 

SEC-65, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 3.

NO

>> Inspection End

3.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-67, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> Inspection End.

NO

>> GO TO 4.

4.

REPLACE ECM

1. Replace ECM.

Refer to 

EC-338, "Removal and Installation"

.

2. Perform “ADDITIONAL SERVICE WHEN REPLACING ECM”.

Refer to 

EC-111, "Work Procedure"

.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2192

ID DISCORD BCM-ECM

The ID verification results between 
BCM and ECM are NG.

• BCM
• ECM

SEC-66

< DTC/CIRCUIT DIAGNOSIS >

B2193 CHAIN OF ECM-IMMU

B2193 CHAIN OF ECM-IMMU

DTC Logic

INFOID:0000000009567417

DTC DETECTION LOGIC

NOTE:

• If DTC B2193 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-57, "DTC Logic"

.

• If DTC B2193 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-58, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-66, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009567418

1.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-67, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

Does the engine start?

YES

>> Inspection End.

NO

>> GO TO 2.

2.

REPLACE ECM

1. Replace ECM.

Refer to 

EC-338, "Removal and Installation"

.

2. Perform “ADDITIONAL SERVICE WHEN REPLACING ECM”.

Refer to 

EC-111, "Work Procedure"

.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2193

CHAIN OF BCM-ECM

Inactive communication between BCM 
and ECM

• Harness or connectors

(The CAN communication line is open or 
shorted.)

• BCM 
• ECM

B2195 ANTI-SCANNING

SEC-67

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2195 ANTI-SCANNING

DTC Logic

INFOID:0000000009567419

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?

YES

>> Refer to 

SEC-67, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009567420

1.

CHECK SELF DIAGNOSTIC RESULT 1

1. Select Self Diagnostic Result mode of BCM using CONSULT.

2. Erase DTC.

3. Perform DTC CONFIRMATION PROCEDURE for DTC B2195. Refer to 

SEC-67, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 2.

NO

>> Inspection End.

2.

CHECK EQUIPMENT OF THE VEHICLE

Check that unspecified accessory part related to engine start is not installed.
Is unspecified accessory part related to engine start installed?

YES

>> GO TO 3.

NO

>> GO TO 4.

3.

CHECK SELF DIAGNOSTIC RESULT 2

1. Obtain the customers approval to remove unspecified accessory part related to engine start, and then

remove it.

2. Select Self Diagnostic Result of BCM using CONSULT.

3. Erase DTC.

4. Perform DTC CONFIRMATION PROCEDURE for DTC B2195. Refer to 

SEC-67, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> Inspection End.

4.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-67, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2195

ANTI-SCANNING

ID verification between BCM and ECM that is 
out of the specified specification is detected.

ID verification request out of the 
specified specification