Nissan Note E12. Manual - part 92

PARKING BRAKE SWITCH

BRC-59

< DTC/CIRCUIT DIAGNOSIS >

[ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-48, "Removal and Installation"

.

NO

>> Repair or replace malfunctioning components.

Component Inspection

INFOID:0000000009365118

1.

CHECK PARKING BRAKE SWITCH

1. Turn ignition switch OFF.

2. Disconnect parking brake switch connector.

3. Check continuity between parking brake switch terminal 1 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace parking brake switch. Refer to 

PB-6, "Exploded View"

.

Combination meter

—

Continuity

Connector

Terminal

M24 10

Ground

No

Parking brake switch terminal

—

Condition

Continuity

1

Ground

Parking brake actuated

Yes

Parking brake released

No

BRC-60

< DTC/CIRCUIT DIAGNOSIS >

[ABS]

ABS WARNING LAMP

ABS WARNING LAMP

Component Function Check

INFOID:0000000009365122

1.

CHECK ABS WARNING LAMP FUNCTION

Check that ABS warning lamp in combination meter turns ON for approximately 2 seconds after ignition switch

is turned ON.
Is the inspection result normal?

YES

>> Inspection End.

NO

>> Proceed to diagnosis procedure. Refer to 

BRC-60, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009365123

1.

PERFORM THE SELF-DIAGNOSIS

With CONSULT.

Perform self diagnostic result.
Are any DTCs detected?

YES

>> Refer to 

BRC-26, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK COMBINATION METER

Check if indication and operation of combination meter are normal. Refer to 

MWI-7, "METER SYSTEM : Sys-

tem Description"

.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-73, "Removal and Installa-

tion"

.

NO

>> Replace combination meter. Refer to 

MWI-48, "Removal and Installation"

.

BRAKE WARNING LAMP

BRC-61

< DTC/CIRCUIT DIAGNOSIS >

[ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

BRAKE WARNING LAMP

Component Function Check

INFOID:0000000009365124

1.

CHECK BRAKE WARNING LAMP FUNCTION (1)

Check that brake warning lamp in combination meter turns ON for approximately 2 seconds after ignition

switch is turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Proceed to diagnosis procedure. Refer to 

BRC-61, "Diagnosis Procedure"

.

2.

CHECK BRAKE WARNING LAMP FUNCTION (2)

Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check parking brake switch system. Refer to 

BRC-58, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009365125

1.

PERFORM THE SELF-DIAGNOSIS

With CONSULT.

Perform self diagnostic result.
Are any DTCs detected?

YES

>> Refer to 

BRC-26, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK COMBINATION METER

Check if indication and operation of combination meter are normal. Refer to 

MWI-7, "METER SYSTEM : Sys-

tem Description"

.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-73, "Removal and Installa-

tion"

.

NO

>> Replace combination meter. Refer to 

MWI-48, "Removal and Installation"

.

BRC-62

< SYMPTOM DIAGNOSIS >

[ABS]

ABS

SYMPTOM DIAGNOSIS

ABS

Symptom Table

INFOID:0000000009365130

If ABS warning lamp turns ON, perform self-diagnosis.

NOTE:
• 1: The ABS does not operate when the speed is 10 km/h (6 MPH) or less.
• 2: Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly depressed (just place a foot on it).

However, this is normal.

- When shifting gears
- When driving on slippery road
- During cornering at high speed
- When passing over bumps or grooves [approximately 50 mm (1.97 in) or more]
- When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher]

Symptom

Check item

Reference

Excessive ABS function operation fre-
quency

Brake force distribution

BRC-63, "Diagno-

sis Procedure"

Looseness of front and rear axle

Wheel sensor and rotor system

Unexpected pedal reaction

Brake pedal stroke

BRC-64, "Diagno-

sis Procedure"

Make sure the braking force is sufficient when the ABS is not operating.

The braking distance is long

Check stopping distance when the ABS is not operating.

BRC-65, "Diagno-

sis Procedure"

ABS function does not operate (Note 1)

ABS actuator and electric unit (control unit)

BRC-66, "Diagno-

sis Procedure"

Pedal vibration or ABS operation sound 
occurs (Note 2)

Brake pedal

BRC-67, "Diagno-

sis Procedure"

ABS actuator and electric unit (control unit)