Nissan Rogue. Manual - part 165

 

  Index      Nissan     Nissan Rogue (2015 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  163  164  165  166   ..

 

 

Nissan Rogue. Manual - part 165

 

 

CALIBRATION OF DECEL G SENSOR

BRC-71

< BASIC INSPECTION >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

3.

CHECK DATA MONITOR

With CONSULT

1. Drive the vehicle. Steer the steering wheel to the straight-ahead position. Stop the vehicle on level sur-

face.

2. Select “ABS”, “Data Monitor”, “ECU INPUT SIGNALS” and “DECEL G SENSOR” in this order. Check that

the signal is within the specified value.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 1.

4.

ERASE SELF DIAGNOSTIC MEMORY

With CONSULT

Erase “Self Diagnosis Result” of “ABS”.
Are the memories erased?

YES

>> Inspection End.

NO

>> Check the items indicated by the “Self Diagnostic Result”.

DECEL G SENSOR

: Approx. 

± 0.01 G

BRC-72

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C1101, C1102, C1103, C1104 WHEEL SENSOR

DTC/CIRCUIT DIAGNOSIS

C1101, C1102, C1103, C1104 WHEEL SENSOR

DTC Logic

INFOID:0000000011280596

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF DIAGNOSTIC RESULT

 With 

CONSULT.

1. Start engine and drive vehicle at approximately 21 km/h (13 MPH) or more for approximately 5 minutes.

2. Perform “Self Diagnostic Result”.
Is DTC C1101, C1102, C1103 or C1104 detected?

YES

>> Proceed to diagnosis procedure. Refer to 

BRC-72, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011280597

Regarding Wiring Diagram information, refer to 

BRC-55, "Wiring Diagram"

.

1.

CONFIRM DTC

 With CONSULT

1. Perform “Self Diagnostic Result” of “ABS” and record all active DTCs.

2. Clear all DTCs.

3. Perform DTC confirmation procedure. Refer to 

BRC-72, "DTC Logic"

.

Does DTC C1101, C1102, C1103 or C1104 reset?

YES

>> GO TO 2.

NO

>> Refer to 

GI-44, "Intermittent Incident"

2.

INSPECT WHEEL SENSOR

Inspect the suspect wheel sensor for damage or deformation.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace as necessary.

3.

HARNESS AND CONNECTOR INSPECTION

DTC

Display Item

Malfunction detected condition

Possible causes

C1101

RR RH SENSOR-1

• When power supply voltage of rear wheel sensor 

RH is low.

• When an open or shorted circuit is detected in rear 

wheel sensor RH circuit.

• Harness or connector
• Wheel sensor
• ABS actuator and electric unit 

(control unit)

C1102

RR LH SENSOR-1

• When power supply voltage of rear wheel sensor 

LH is low.

• When an open or shorted circuit is detected in rear 

wheel sensor LH circuit.

C1103

FR RH SENSOR-1

• When power supply voltage of front wheel sensor 

RH is low.

• When an open or shorted circuit is detected in front 

wheel sensor RH circuit.

C1104

FR LH SENSOR-1

• When power supply voltage of front wheel sensor 

LH is low.

• When an open or shorted circuit is detected in front 

wheel sensor LH circuit.

C1101, C1102, C1103, C1104 WHEEL SENSOR

BRC-73

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

1. Disconnect ABS actuator and electric unit (control unit) connector E125 and wheel sensor connector of

suspect wheel.

2. Check harness, connectors and terminals for corrosion, deformation, disconnection, looseness or dam-

age.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace as necessary.

4.

CHECK WHEEL SENSOR OUTPUT SIGNAL

1. Connect ABS active wheel sensor tester (J-45741) to wheel sensor using appropriate adapter.

2. Turn on the ABS active wheel sensor tester power switch.

NOTE:

The green POWER indicator should illuminate. If the POWER indicator does not illuminate, replace the

battery in the ABS active wheel sensor tester before proceeding.

3. Spin the wheel of the vehicle by hand and observe the red SENSOR indicator on the ABS active wheel

sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

NOTE:

If the red SENSOR indicator illuminates but does not flash, reverse the polarity of the tester leads and

retest.

Does the ABS active wheel sensor tester detect a signal?

YES

>> GO TO 5.

NO

>> Replace the wheel sensor. Refer to 

BRC-130, "FRONT WHEEL SENSOR : Removal and Installa-

tion"

 or 

BRC-132, "REAR WHEEL SENSOR : Removal and Installation"

.

5.

CHECK WIRING HARNESS FOR SHORT TO VOLTAGE

1. Turn ignition switch ON.

2. Check voltage between wheel sensor harness connector terminals of suspect wheel and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair the circuit.

6.

CHECK WIRING HARNESS FOR SHORT TO GROUND

1. Turn ignition switch OFF.

2. Check continuity between wheel sensor harness connector terminals of suspect wheel and ground.

Wheel Sensor

Ground

Voltage

Wheel

Connector

Terminal

Front LH

E18

1

0V

2

Front RH

E43

1

2

Rear LH

B58

1

2

Rear RH

B60

1

2

Wheel Sensor

Ground

Continuity

Wheel

Connector

Terminal

BRC-74

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C1101, C1102, C1103, C1104 WHEEL SENSOR

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair the circuit.

7.

CHECK WIRING HARNESS FOR SHORT BETWEEN CIRCUITS

Check continuity between wheel sensor harness connector terminals of suspect wheel.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair the circuit.

8.

CHECK WIRING HARNESS FOR OPEN CIRCUIT

Check continuity between ABS actuator and electric unit (control unit) harness connector E125 and harness

connector of suspect wheel sensor.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair the circuit.

9.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY CIRCUIT

1. Turn ignition switch ON.

2. Check voltage between ABS actuator and electric unit (control unit) harness connector E125 terminal and

ground.

Front LH

E18

1

No

2

Front RH

E43

1

2

Rear LH

B58

1

2

Rear RH

B60

1

2

Wheel Sensor

(+)

(-)

Continuity

Wheel

Connector

Terminal

Terminal

Front LH

E18

1

2

No

Front RH

E43

Rear LH

B58

Rear RH

B60

Wheel sensor

ABS actuator and electric unit (control unit)

Wheel sensor

Continuity

Connector

Terminal

Connector

Terminal

Yes

Front LH

E125

19

E18

1

8

2

Front RH

16

E43

1

4

2

Rear LH

31

B58

1

18

2

Rear RH

17

B60

1

29

2

 

 

 

 

 

 

 

Content   ..  163  164  165  166   ..