Nissan Rogue. Manual - part 1259

FRONT WIPER AUTO STOP SIGNAL CIRCUIT

WW-39

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

YES

>> Replace front wiper motor. Refer to 

WW-69, "Removal and Installation"

.

NO

>> Repair or replace harness.

WW-40

< DTC/CIRCUIT DIAGNOSIS >

FRONT WIPER MOTOR GROUND CIRCUIT

FRONT WIPER MOTOR GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000011280398

Regarding Wiring Diagram information, refer to 

WW-20, "Wiring Diagram"

.

1.

 CHECK FRONT WIPER MOTOR GROUND CIRCUIT 

1. Turn the ignition switch OFF.

2. Disconnect front wiper motor.

3. Check continuity between front wiper motor harness connector and ground.

Is the inspection result normal?

YES

>> Front wiper motor ground circuit is normal.

NO

>> Repair or replace harness.

Front wiper motor

Ground

Continuity

Connector

Terminal

E20

2

Yes

WASHER MOTOR CIRCUIT

WW-41

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

WASHER MOTOR CIRCUIT

Diagnosis Procedure

INFOID:0000000011280399

Regarding Wiring Diagram information, refer to 

WW-20, "Wiring Diagram"

.

1.

 CHECK FRONT AND REAR WASHER MOTOR FUSE

1. Turn the ignition switch OFF.

2. Check that the following fuse is not blown:

Is the fuse blown?

YES

>> Replace the blown fuse after repairing the affected circuit.

NO

>> GO TO 2.

2.

 CHECK FRONT AND REAR WASHER MOTOR POWER SUPPLY

1. Disconnect front and rear washer motor.

2. Turn ignition switch ON.

3. Check voltage between front and rear washer motor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the harness or connectors.

3.

 CHECK FRONT AND REAR WASHER MOTOR CIRCUIT CONTINUITY

1. Turn the ignition switch OFF.

2. Disconnect combination switch (wiper and washer switch).

3. Check continuity between combination switch (wiper and washer switch) harness connector and front and

rear washer motor.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the harness or connectors.

4.

 CHECK WIPER AND WASHER SWITCH GROUND CIRCUIT

Check continuity between combination switch (wiper and washer switch) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the harness or connectors.

5.

 CHECK WIPER AND WASHER SWITCH

Check wiper and washer switch. Refer to 

WW-43, "Component Inspection"

.

Unit

Location

Fuse No.

Capacity

Front and rear washer motor

Fuse block (J/B)

33

15A

Front and rear washer motor

Ground

Voltage

(Approx.)

Connector

Terminal

E41

1

Battery voltage

Combination switch (wiper and washer switch) 

Front and rear washer motor

Continuity

Connector

Terminal

Connector

Terminal

M28

11

E41

1

Yes

Combination switch (wiper and washer switch)

Ground

Continuity

Connector

Terminal

M28

16

Yes

WW-42

< DTC/CIRCUIT DIAGNOSIS >

WASHER MOTOR CIRCUIT

Is the inspection result normal?

YES

>> Replace front and rear washer motor. Refer to 

WW-56, "Removal and Installation"

.

NO

>> Replace wiper and washer switch. Refer to 

BCS-76, "Removal and Installation"

.