Nissan Rogue. Manual - part 1181

TM-96

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

U0102 LOST COMMUNICATION (TRANSFER)

U0102 LOST COMMUNICATION (TRANSFER)

DTC Description

INFOID:0000000011279311

DTC DETECTION LOGIC

POSSIBLE CAUSE

• AWD control unit

• Harness or connector (CAN communication line is open or shorted)

FAIL-SAFE

Not changed from normal driving

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Start the engine and wait for at least 5 seconds.

2. Check the DTC.
Is “U0102” detected?

YES

>> Go to 

TM-103, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000011279312

For the diagnosis procedure, refer to 

LAN-17, "Trouble Diagnosis Flow Chart"

. 

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

U0102

LOST COMM (TRANSFER)
(Lost Communication With Transfer Case Con-
trol Module)

When the ignition switch is ON, TCM is unable to receive the CAN com-
munications signal from AWD control unit continuously for 2 seconds or 
more.

U0140 LOST COMMUNICATION (BCM)

TM-97

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

U0140 LOST COMMUNICATION (BCM)

DTC Description

INFOID:0000000011279313

DTC DETECTION LOGIC

POSSIBLE CAUSE

• BCM

• Harness or connector (CAN communication line is open or shorted)

FAIL-SAFE

Not changed from normal driving

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Start the engine and wait for at least 5 seconds.

2. Check the DTC.
Is “U0140” detected?

YES

>> Go to 

TM-97, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000011279314

For the diagnosis procedure, refer to 

LAN-17, "Trouble Diagnosis Flow Chart"

. 

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

U0140

LOST COMM (BCM)
(Lost Communication With Body Control Mod-
ule)

When the ignition switch is ON, TCM is unable to receive the CAN com-
munications signal from BCM continuously for 2 seconds or more.

TM-98

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

U0141 LOST COMMUNICATION (BCM A)

U0141 LOST COMMUNICATION (BCM A)

DTC Description

INFOID:0000000011279315

DTC DETECTION LOGIC

POSSIBLE CAUSE

• IPDM E/R

• Harness or connector (CAN communication line is open or shorted)

FAIL-SAFE

Not changed from normal driving

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Start the engine and wait for at least 5 seconds.

2. Check the DTC.
Is “U0141” detected?

YES

>> Go to 

TM-98, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000011279316

For the diagnosis procedure, refer to 

LAN-17, "Trouble Diagnosis Flow Chart"

. 

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

U0141

LOST COMM (BCM A)
(Lost Communication With Body Control Mod-
ule A)

When the ignition switch is turned ON, TCM continues no reception of 
the CAN communication signal from IPDM E/R for 2 seconds or more. 

U0155 LOST COMMUNICATION (IPC)

TM-99

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

U0155 LOST COMMUNICATION (IPC)

DTC Description

INFOID:0000000011279317

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Combination meter

• Harness or connector (CAN communication line is open or shorted)

FAIL-SAFE

Not changed from normal driving

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Start the engine and wait for at least 5 seconds.

2. Check the DTC.
Is “U0155” detected?

YES

>> Go to 

TM-99, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000011279318

For the diagnosis procedure, refer to 

LAN-17, "Trouble Diagnosis Flow Chart"

. 

DTC

CONSULT screen terms

[Trouble diagnosis content]

DTC detection condition

U0155

LOST COMM (IPC)
[Lost Communication With Instrument Panel 
Cluster (IPC) Control Module]

When the ignition switch is ON, TCM is unable to receive the CAN com-
munications signal from the combination meter continuously for 2 sec-
onds or more.