Nissan Sentra. Manual - part 901

TM-240

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

SHIFT POSITION INDICATOR CIRCUIT

SHIFT POSITION INDICATOR CIRCUIT

Component Parts Function Inspection

INFOID:0000000009759488

1.

CHECK SHIFT POSITION INDICATOR

1. Start the engine.

2. Shift selector lever.

3. Check that the selector lever position and the shift position indicator on the combination meter are identi-

cal.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

TM-240, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009759489

1.

CHECK TCM INPUT/OUTPUT SIGNAL 

With CONSULT

1. Start the engine.

2. Select “Data Monitor” in “TRANSMISSION”.

3. Select “RANGE”. 

4. Shift selector lever.

5. Check that selector lever position, “RANGE” on the CONSULT screen, and shift position indicator display

on the combination meter are identical.

 Is the check result normal?

YES

>> INSPECTION END

NO-1 (“RANGE” is changed but is not displayed on the shift position indicator.>>Check  “Self  Diagnostic

Result” in “TRANSMISSION”.

NO-2 (“RANGE” and shift position indicator are different.)>>Check “Self Diagnostic Result” in “TRANSMIS-

SION”.

NO-3 (Specific“RANGE” is not displayed on the shift position indicator.)>>Check “Self Diagnostic Result” in

“METER/M&A”.

SHIFT LOCK SYSTEM

TM-241

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

SHIFT LOCK SYSTEM

Component Function Check

INFOID:0000000009759490

1.

CHECK SHIFT LOCK OPERATION (PART 1)

1. Turn ignition switch ON.

2. Shift the selector lever to park “P” position.

3. Attempt to shift the selector lever to any other position with the brake pedal released.
Can the selector lever be shifted to any other position?

YES

>> Go to 

TM-241, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK SHIFT LOCK OPERATION (PART 2)

Attempt to shift the selector lever to any other position with the brake pedal depressed.
Can the selector lever be shifted to any other position?

YES

>> Inspection End.

NO

>> Go to 

TM-241, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009759491

Regarding Wiring Diagram information, refer to 

TM-136, "Wiring Diagram"

.

1.

CHECK POWER SOURCE (PART 1)

1. Turn ignition switch OFF.

2. Disconnect stop lamp switch connector.

3. Turn ignition switch ON.

4. Check the voltage between the stop lamp switch harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 9.

2.

CHECK STOP LAMP SWITCH MOUNTING POSITION

Check stop lamp switch mounting position. Refer to 

BR-15, "Adjustment"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Adjust stop lamp switch mounting position.

3.

CHECK STOP LAMP SWITCH

Check stop lamp switch. Refer to 

TM-243, "Component Inspection (Stop Lamp Switch)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace stop lamp switch.

4.

CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 1)

1. Disconnect CVT shift selector connector.

2. Check the continuity between the stop lamp switch harness connector terminal and the CVT shift selector

harness connector terminal.

+

–

Voltage

Stop lamp switch

Connector

Terminal

E60

3

Ground

Battery voltage

TM-242

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

SHIFT LOCK SYSTEM

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 2)

Check the continuity between the stop lamp switch harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace damaged parts.

6.

CHECK GROUND CIRCUIT

Check the continuity between the CVT shift selector harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace damaged parts.

7.

CHECK PART POSITION SWITCH

1. Disconnect park position switch connector.

2. Check park position switch. Refer to 

TM-243, "Component Inspection (Park Position Switch)"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace damaged parts.

8.

CHECK SHIFT LOCK SOLENOID

1. Disconnect shift lock solenoid connector.

2. Check shift lock solenoid. Refer to 

TM-243, "Component Inspection (Shift Lock Solenoid)"

.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair or replace damaged parts.

9.

DETECT MALFUNCTIONING ITEM

Check the following items:

• Open or short circuit of the harness between ignition switch and stop lamp switch connector. Refer to 

PG-20,

"Wiring Diagram — Ignition Power Supply —"

• Ignition switch

• 10A fuse [No.5, fuse block (J/B)]. Refer to 

PG-47, "Terminal Arrangement"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

NO

>> Repair or replace damaged parts.

Stop lamp switch

CVT shift selector

Continuity

Connector

Terminal

Connector

Terminal

E60

4

M38

3

Yes

Stop lamp switch

—

Continuity

Connector

Terminal

E60

4

Ground

No

CVT shift selector

—

Continuity

Connector

Terminal

M38

4

Ground

Yes

SHIFT LOCK SYSTEM

TM-243

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Component Inspection (Shift Lock Solenoid)

INFOID:0000000009759492

1.

CHECK SHIFT LOCK SOLENOID

Apply voltage to terminals of shift lock solenoid and park position switch (shift selector) connector and check

that shift lock solenoid is activated.

CAUTION:

• Connect a fuse between the terminals when applying voltage.

• Never cause shorting between terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace CVT shift selector. Refer to 

TM-253, "Removal and Installation"

.

Component Inspection (Park Position Switch)

INFOID:0000000009759493

1.

CHECK PARK POSITION SWITCH (SHIFT SELECTOR)

Apply voltage to terminals of shift lock solenoid and park position switch (shift selector) connector and check

that shift lock solenoid is activated.

CAUTION:

• Connect a fuse between the terminals when applying voltage.

• Never cause shorting between terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace CVT shift selector. Refer to 

TM-253, "Removal and Installation"

.

Component Inspection (Stop Lamp Switch)

INFOID:0000000009759494

1.

CHECK STOP LAMP SWITCH

Check the continuity between the stop lamp switch connector terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace stop lamp switch. Refer to 

BR-22, "Exploded View"

.

+ (fuse)

-

Condition

Status

Shift lock solenoid

Terminal

3

4

Apply 12 V  between termi-
nals 3 and 4 with the park 
position switch (shift selec-
tor) in the "P" (park) posi-
tion.

Shift lock solenoid operates

+ (fuse)

-

Condition

Status

Shift lock solenoid

Terminal

3

4

Apply 12 V  between termi-
nals 3 and 4 with the park 
position switch (shift selec-
tor) in the "P" (park) posi-
tion.

Shift lock solenoid operates

Stop lamp switch

Condition

Continuity

Terminal

3 – 4

Depressed brake pedal

Yes

Released brake pedal

No